Showing papers in "arXiv: Materials Science in 2012"

Observation of tightly bound trions in monolayer MoS2

Abstract: Two-dimensional (2D) atomic crystals, such as graphene and transition-metal dichalcogenides, have emerged as a new class of materials with remarkable physical properties. In contrast to graphene, monolayer MoS2 is a non-centrosymmetric material with a direct energy gap. Strong photoluminescence, a current on-off ratio exceeding 10^8 in field-effect transistors, and efficient valley and spin control by optical helicity have recently been demonstrated in this material. Here we report the spectroscopic identification in doped monolayer MoS2 of tightly bound negative trions, a quasi-particle composed of two electrons and a hole. These quasi-particles, which can be created with valley and spin polarized holes, have no analogue in other semiconducting materials. They also possess a large binding energy (~ 20 meV), rendering them significant even at room temperature. Our results open up new avenues both for fundamental studies of many-body interactions and for opto-electronic and valleytronic applications in 2D atomic crystals.

Enhanced Catalytic Activity in Strained Chemically Exfoliated WS2 Nanosheets for Hydrogen Evolution

Abstract: The ability to efficiently evolve hydrogen via electrocatalysis at low overpotentials holds tremendous promise for clean energy. Hydrogen evolution reaction (HER) can be easily achieved from water if a voltage above the thermodynamic potential of the HER is applied. Large overpotentials are energetically inefficient but can be lowered with expensive platinum based catalysts. Replacement of Pt with inexpensive, earth abundant electrocatalysts would be significantly beneficial for clean and efficient hydrogen evolution. Towards this end, promising HER characteristics have been reported using 2H (trigonal prismatic) XS2 (where X = Mo or W) nanoparticles with a high concentration of metallic edges as electrocatalysts. The key challenges for HER with XS2 are increasing the number and catalytic activity of active sites. Here we report atomically thin nanosheets of chemically exfoliated WS2 as efficient catalysts for hydrogen evolution with very low overpotentials. Atomic-resolution transmission electron microscopy and spectroscopy analyses indicate that enhanced electrocatalytic activity of WS2 is associated with high concentration of strained metallic 1T (octahedral) phase in the as-exfoliated nanosheets. Density functional theory calculations reveal that the presence of strain in the 1T phase leads to an enhancement of the density of states at the Fermi level and increases the catalytic activity of the WS2 nanosheet. Our results suggest that chemically exfoliated WS2 nanosheets could be interesting catalysts for hydrogen evolution.

Evolution of Electronic Structure in Atomically Thin Sheets of WS2 and WSe2

Abstract: Geometrical confinement effect in exfoliated sheets of layered materials leads to significant evolution of energy dispersion with decreasing layer thickness. Molybdenum disulphide (MoS2) was recently found to exhibit indirect to direct gap transition when the thickness is reduced to a single monolayer. This leads to remarkable enhancement in the photoluminescence efficiency, which opens up new opportunities for the optoelectronic applications of the material. Here we report differential reflectance and photoluminescence (PL) spectra of mono- to few-layer WS2 and WSe2 that indicate that the band structure of these materials undergoes similar indirect to direct transition when thinned to a single monolayer. Strong enhancement in PL quantum yield is observed for monoayer WS2 and WSe2 due to exciton recombination at the direct band edge. In contrast to natural MoS2 crystals extensively used in recent studies, few-layer WS2 and WSe2 show comparatively strong indirect gap emission along with distinct direct gap hot electron emission, suggesting high quality of synthetic crystals prepared by chemical vapor transport method. Fine absorption and emission features and their thickness dependence suggest strong effect of Se p-orbitals on the d electron band structure as well as interlayer coupling in WSe2.

Covalent Hybrid of Spinel Manganese-Cobalt Oxide and Gra-phene as Advanced Oxygen Reduction Electrocatalysts

Abstract: Through direct nanoparticle nucleation and growth on nitrogen doped, reduced graphene oxide sheets and cation substitution of spinel Co3O4 nanoparticles, a manganese-cobalt spinel MnCo2O4/graphene hybrid was developed as a highly efficient electrocatalyst for oxygen reduction reaction (ORR) in alkaline conditions. Electrochemical and X-ray near edge structure (XANES) investigations revealed that the nucleation and growth method for forming inorganic-nanocarbon hybrid results in covalent coupling between spinel oxide nanoparticles and N-doped reduced graphene oxide (N-rmGO) sheets. Carbon K-edge and nitrogen K-edge XANES showed strongly perturbed C-O and C-N bonding in the N-rmGO sheet, suggesting the formation of C-O-metal and C-N-metal bonds between N-doped graphene oxide and spinel oxide nanoparticles. Co L-edge and Mn L-edge XANES suggested substitu-tion of Co3+ sites by Mn3+, which increased the activity of the catalytic sites in the hybrid materials, further boosting the ORR activity compared to the pure cobalt oxide hybrid. The covalently bonded hybrid afforded much greater activity and durability than the physi-cal mixture of nanoparticles and carbon materials including N-rmGO. At the same mass loading, the MnCo2O4/N-graphene hybrid can outperform Pt/C in ORR current density at medium overpotentials with superior stability to Pt/C in alkaline solutions.

Epitaxial Growth of a Silicene Sheet

Abstract: Using atomic resolved scanning tunneling microscopy, we present here the experimental evidence of a silicene sheet (graphene like structure) epitaxially grown on a close-packed silver surface (Ag(111)). This has been achieved via direct condensation of a silicon atomic flux onto the single-crystal substrate in ultra-high vacuum conditions. A highly ordered silicon structure, arranged within a honeycomb lattice is synthesized and presenting two silicon sub-lattices occupying positions at different heights (0.02 nm) indicating possible sp2-sp3 hybridizations.

Structure identification methods for atomistic simulations of crystalline materials

Abstract: We discuss existing and new computational analysis techniques to classify local atomic arrangements in large-scale atomistic computer simulations of crystalline solids. This article includes a performance comparison of typical analysis algorithms such as Common Neighbor Analysis, Centrosymmetry Analysis, Bond Angle Analysis, Bond Order Analysis, and Voronoi Analysis. In addition we propose a simple extension to the Common Neighbor Analysis method that makes it suitable for multi-phase systems. Finally, we introduce a new structure identification algorithm, the Neighbor Distance Analysis, that is designed to identify atomic structure units in grain boundaries.

Photonic Analogue of Two-dimensional Topological Insulators and Helical One-Way Edge Transport in Bi-Anisotropic Metamaterials

Abstract: Recent progress in understanding the topological properties of condensed matter has led to the discovery of time-reversal invariant topological insulators. Because of limitations imposed by nature, topologically non-trivial electronic order seems to be uncommon except in small-band-gap semiconductors with strong spin-orbit interactions. In this Article we show that artificial electromagnetic structures, known as metamaterials, provide an attractive platform for designing photonic analogues of topological insulators. We demonstrate that a judicious choice of the metamaterial parameters can create photonic phases that support a pair of helical edge states, and that these edge states enable one-way photonic transport that is robust against disorder.

Spin transfer torque devices utilizing the giant spin Hall effect of tungsten

Abstract: We report a giant spin Hall effect (SHE) in {\beta}-W thin films. Using spin torque induced ferromagnetic resonance with a {\beta}-W/CoFeB bilayer microstrip we determine the spin Hall angle to be |\theta|=0.30\pm0.02, large enough for an in-plane current to efficiently reverse the orientation of an in-plane magnetized CoFeB free layer of a nanoscale magnetic tunnel junction adjacent to a thin {\beta}-W layer. From switching data obtained with such 3-terminal devices we independently determine |\theta|=0.33\pm0.06. We also report variation of the spin Hall switching efficiency with W layers of different resistivities and hence of variable ({\alpha} and {\beta}) phase composition.

Graphene -- Based Nanocomposites as Highly Efficient Thermal Interface Materials

Abstract: We found that an optimized mixture of graphene and multilayer graphene - produced by the high-yield inexpensive liquid-phase-exfoliation technique - can lead to an extremely strong enhancement of the cross-plane thermal conductivity K of the composite. The "laser flash" measurements revealed a record-high enhancement of K by 2300 % in the graphene-based polymer at the filler loading fraction f =10 vol. %. It was determined that a relatively high concentration of single-layer and bilayer graphene flakes (~10-15%) present simultaneously with thicker multilayers of large lateral size (~ 1 micrometer) were essential for the observed unusual K enhancement. The thermal conductivity of a commercial thermal grease was increased from an initial value of ~5.8 W/mK to K=14 W/mK at the small loading f=2%, which preserved all mechanical properties of the hybrid. Our modeling results suggest that graphene - multilayer graphene nanocomposite used as the thermal interface material outperforms those with carbon nanotubes or metal nanoparticles owing to graphene's aspect ratio and lower Kapitza resistance at the graphene - matrix interface.

PDFgetX3: A rapid and highly automatable program for processing powder diffraction data into total scattering pair distribution functions

Abstract: PDFgetX3 is a new software application for converting X-ray powder diffraction data to atomic pair distribution function (PDF). PDFgetX3 has been designed for ease of use, speed and automated operation. The software can readily process hundreds of X-ray patterns within few seconds and is thus useful for high-throughput PDF studies, that measure numerous datasets as a function of time, temperature or other environment parameters. In comparison to the preceding programs, PDFgetX3 requires fewer inputs, less user experience and can be readily adopted by novice users. The live-plotting interactive feature allows to assess the effects of calculation parameters and select their optimum values. PDFgetX3 uses an ad-hoc data correction method, where the slowly-changing structure independent signal is filtered out to obtain coherent X-ray intensities that contain structure information. The outputs from PDFgetX3 have been verified by processing experimental PDFs from inorganic, organic and nanosized samples and comparing them to their counterparts from previous established software. In spite of different algorithm, the obtained PDFs were nearly identical and yielded highly similar results when used in structure refinement. PDFgetX3 is written in Python language and features well documented, reusable codebase. The software can be used either as standalone application or as a library of PDF-processing functions that can be called on from other Python scripts. The software is free for open academic research, but requires paid license for commercial use.

Thermodynamic Oxidation and Reduction Potentials of Photocatalytic Semiconductors in Aqueous Solution

Abstract: We introduce an approach to calculate the thermodynamic oxidation and reduction potentials of semiconductors in aqueous solution. By combining a newly-developed ab initio calculation for compound formation energy and band alignment with electrochemistry experimental data, this approach can be used to predict the stability of almost any compound semiconductor in aqueous solution. 30 photocatalytic semiconductors have been studied, and a graph (a simplified Pourbaix diagram) showing their valence/conduction band levels and oxidation/reduction potentials is produced. Based on this graph, we have studied the stabilities and trends against the oxidative and reductive photocorrosion for compound semiconductors. We found that, only metal oxides can be thermodynamically stable when used as the n-type photoanodes. All the non-oxides are unstable due to easy oxidation by the photogenerated holes, but they can be resistant to the reduction by electrons, thus stable as the p-type photocathodes.

Topological crystalline insulator states in Pb(1-x)Sn(x)Se

Abstract: Topological insulators are a novel class of quantum materials in which time-reversal symmetry, relativistic (spin-orbit) effects and an inverted band structure result in electronic metallic states on the surfaces of bulk crystals. These helical states exhibit a Dirac-like energy dispersion across the bulk bandgap, and they are topologically protected. Recent theoretical proposals have suggested the existence of topological crystalline insulators, a novel class of topological insulators in which crystalline symmetry replaces the role of time-reversal symmetry in topological protection [1,2]. In this study, we show that the narrow-gap semiconductor Pb(1-x)Sn(x)Se is a topological crystalline insulator for x=0.23. Temperature-dependent magnetotransport measurements and angle-resolved photoelectron spectroscopy demonstrate that the material undergoes a temperature-driven topological phase transition from a trivial insulator to a topological crystalline insulator. These experimental findings add a new class to the family of topological insulators. We expect these results to be the beginning of both a considerable body of additional research on topological crystalline insulators as well as detailed studies of topological phase transitions.

Theory of Chemical Kinetics and Charge Transfer based on Nonequilibrium Thermodynamics

Abstract: Classical theories of chemical kinetics assume independent reactions in dilute solutions, whose rates are determined by mean concentrations In condensed matter, strong interactions alter chemical activities and create inhomogeneities that can dramatically affect the reaction rate The extreme case is that of a reaction coupled to a phase transformation, whose kinetics must depend on the order parameter -- and its gradients, at phase boundaries This Account presents a general theory of chemical kinetics based on nonequilibrium thermodynamics The reaction rate is a nonlinear function of the thermodynamic driving force (free energy of reaction) expressed in terms of variational chemical potentials The Cahn-Hilliard and Allen-Cahn equations are unified and extended via a master equation for non-equilibrium chemical thermodynamics For electrochemistry, both Marcus and Butler-Volmer kinetics are generalized for concentrated solutions and ionic solids The theory is applied to intercalation dynamics in the phase separating Li-ion battery material Li$_x$FePO$_4$

Graphene Oxide vs. Reduced Graphene Oxide as saturable absorbers for Er-doped passively mode-locked fiber laser

Abstract: In this work we demonstrate comprehensive studies on graphene oxide (GO) and reduced graphene oxide (rGO) based saturable absorbers (SA) for mode-locking of Er-doped fiber lasers. The paper describes the fabrication process of both saturable absorbers and detailed comparison of their parameters. Our results show, that there is no significant difference in the laser performance between the investigated SA. Both provided stable, mode-locked operation with sub-400 fs soliton pulses and more than 9 nm optical bandwidth at 1560 nm center wavelength. It has been shown that GO might be successfully used as an efficient SA without the need of its reduction to rGO. Taking into account simpler manufacturing technology and the possibility of mass production, GO seems to be a good candidate as a cost-effective material for saturable absorbers for Er-doped fiber lasers.

Colossal electroresistance in metal/ferroelectric/semiconductor tunnel diodes for resistive switching memories

Abstract: We propose a tunneling heterostructure by replacing one of the metal electrodes in a metal/ferroelectric/metal ferroelectric tunnel junction with a heavily doped semiconductor. In this metal/ferroelectric/semiconductor tunnel diode, both the height and the width of the tunneling barrier can be electrically modulated due to the ferroelectric field effect, leading to a colossal tunneling electroresistance. This idea is implemented in Pt/BaTiO3/Nb:SrTiO3 heterostructures, in which an ON/OFF conductance ratio above 10$^4$ can be readily achieved at room temperature. The colossal tunneling electroresistance, reliable switching reproducibility and long data retention observed in these ferroelectric tunnel diodes suggest their great potential in non-destructive readout nonvolatile memories.

Domain wall motion governed by the spin Hall effect

Abstract: Perpendicularly magnetized materials have attracted tremendous interest due to their high anisotropy, which results in extremely narrow, nano-sized domain walls. As a result, the recently studied current-induced domain wall motion (CIDWM) in these materials promises to enable a novel class of data, memory, and logic devices. In this letter, we propose the spin Hall effect as a radically new mechanism for CIDWM. We are able to carefully tune the net spin Hall current in depinning experiments on Pt/Co/Pt nanowires, offering unique control over CIDWM. Furthermore, we determine that the depinning efficiency is intimately related to the internal structure of the domain wall, which we control by small fields along the nanowire. This new manifestation of CIDWM offers a very attractive new degree of freedom for manipulating domain wall motion by charge currents, and sheds light on the existence of contradicting reports on CIDWM in perpendicularly magnetized materials.

Error estimates for solid-state density-functional theory predictions: an overview by means of the ground-state elemental crystals

Abstract: Predictions of observable properties by density-functional theory calculations (DFT) are used increasingly often in experimental condensed-matter physics and materials engineering as data. These predictions are used to analyze recent measurements, or to plan future experiments. Increasingly more experimental scientists in these fields therefore face the natural question: what is the expected error for such an ab initio prediction? Information and experience about this question is scattered over two decades of literature. The present review aims to summarize and quantify this implicit knowledge. This leads to a practical protocol that allows any scientist - experimental or theoretical - to determine justifiable error estimates for many basic property predictions, without having to perform additional DFT calculations. A central role is played by a large and diverse test set of crystalline solids, containing all ground-state elemental crystals (except most lanthanides). For several properties of each crystal, the difference between DFT results and experimental values is assessed. We discuss trends in these deviations and review explanations suggested in the literature. A prerequisite for such an error analysis is that different implementations of the same first-principles formalism provide the same predictions. Therefore, the reproducibility of predictions across several mainstream methods and codes is discussed too. A quality factor Delta expresses the spread in predictions from two distinct DFT implementations by a single number. To compare the PAW method to the highly accurate APW+lo approach, a code assessment of VASP and GPAW with respect to WIEN2k yields Delta values of 1.9 and 3.3 meV/atom, respectively. These differences are an order of magnitude smaller than the typical difference with experiment, and therefore predictions by APW+lo and PAW are for practical purposes identical.

On the feasibility of pentamode mechanical metamaterials

Abstract: Following the theoretical suggestion by Milton and Cherkaev in 1995, we fabricate pentamode metamaterials by dip-in direct-laser-writing optical lithography. Using finite element calculations and geometrical parameters corresponding to our fabricated three-dimensional microstructures, we find that the figure of merit, i.e., the ratio of bulk modulus to shear modulus, can realistically be made as large as about 1,000. This result opens new horizons for transformation acoustics.

Stability and Hydrolyzation of Metal Organic Frameworks with Paddle-Wheel SBUs upon Hydration

Abstract: Instability of most prototypical metal organic frameworks (MOFs) in the presence of moisture is always a limita- tion for industrial scale development. In this work, we examine the dissociation mechanism of microporous paddle wheel frameworks M(bdc)(ted)0.5 [M=Cu, Zn, Ni, Co; bdc= 1,4-benzenedicarboxylate; ted= triethylenediamine] in controlled humidity environments. Combined in-situ IR spectroscopy, Raman, and Powder x-ray diffraction measurements show that the stability and modification of isostructual M(bdc)(ted)0.5 compounds upon exposure to water vapor critically depend on the central metal ion. A hydrolysis reaction of water molecules with Cu-O-C is observed in the case of Cu(bdc)(ted)0.5. Displacement reactions of ted linkers by water molecules are identified with Zn(bdc)(ted)0.5 and Co(bdc)(ted)0.5. In contrast,. Ni(bdc)(ted)0.5 is less suscept- ible to reaction with water vapors than the other three compounds. In addition, the condensation of water vapors into the framework is necessary to initiate the dissociation reaction. These findings, supported by supported by first principles theoretical van der Waals density functional (vdW-DF) calculations of overall reaction enthalpies, provide the necessary information for de- termining operation conditions of this class of MOFs with paddle wheel secondary building units and guidance for developing more robust units.

Optical and Luminescence Properties of Zinc Oxide

Abstract: We generalize and systematize basic experimental data on optical and luminescence properties of ZnO single crystals, thin films, powders, ceramics, and nanocrystals. We consider and study mechanisms by which two main emission bands occur, a short-wavelength band near the fundamental absorption edge and a broad long-wavelength band, the maximum of which usually lies in the green spectral range. We determine a relationship between the two luminescence bands and study in detail the possibility of controlling the characteristics of ZnO by varying the maximum position of the short-wavelength band. We show that the optical and luminescence characteristics of ZnO largely depend on the choice of the corresponding impurity and the parameters of the synthesis and subsequent treatment of the sample. Prospects for using zinc oxide as a scintillator material are discussed. Additionally, we consider experimental results that are of principal interest for practice.

High Mobility in a Stable Transparent Perovskite Oxide

Abstract: We discovered that La-doped BaSnO3 with the perovskite structure has an unprecedentedly high mobility at room temperature while retaining its optical transparency. In single crystals, the mobility reached 320 cm^2(Vs)^-1 at a doping level of 8x10^19 cm^-3, constituting the highest value among wide-band-gap semiconductors. In epitaxial films, the maximum mobility was 70 cm^2(Vs)^-1 at a doping level of 4.4x10^20 cm^-3. We also show that resistance of (Ba,La)SnO3 changes little even after a thermal cycle to 530 Deg. C in air, pointing to an unusual stability of oxygen atoms and great potential for realizing transparent high-frequency, high-power functional devices.

Microscopic theory of singlet exciton fission. II. Application to pentacene dimers and the role of superexchange

Abstract: In the preceding paper, we assembled the theoretical components necessary for a unified framework of singlet fission, a type of multiexciton generation producing two triplet excitons from one singlet exciton. In this paper, we apply our methodology to molecular dimers of pentacene, a widely studied material that exhibits singlet fission. We address a longstanding theoretical issue, namely whether singlet fission proceeds via two sequential electron transfer steps mediated by a charge-transfer state or via a direct two-electron transfer process. We find evidence for a superexchange mediated mechanism, whereby the fission process proceeds through virtual charge-transfer states which may be very high in energy. In particular, this mechanism predicts efficient singlet fission on the sub-picosecond timescale, in reasonable agreement with experiment. We investigate the role played by molecular vibrations in mediating relaxation and decoherence, finding that different physically reasonable forms for the bath relaxation function give similar results. We also examine the competing direct coupling mechanism and find it to yield fission rates slower in comparison with the superexchange mechanism for the dimer. We discuss implications for crystalline pentacene, including the limitations of the dimer model.

Group-IV graphene- and graphane-like nanosheets

Abstract: We performed a first principles investigation on the structural and electronic properties of group-IV (C, SiC, Si, Ge, and Sn) graphene-like sheets in flat and buckled configurations and the respective hydrogenated or fluorinated graphane-like ones. The analysis on the energetics, associated with the formation of those structures, showed that fluorinated graphane-like sheets are very stable, and should be easily synthesized in laboratory. We also studied the changes on the properties of the graphene-like sheets, as result of hydrogenation or fluorination. The interatomic distances in those graphane-like sheets are consistent with the respective crystalline ones, a property that may facilitate integration of those sheets within three-dimensional nanodevices.

Micro-Raman Spectroscopy of Mechanically Exfoliated Few-Quintuple Layers of Bi(2)Te(3), Bi(2)Se(3) and Sb(2)Te(3) Materials

Abstract: Bismuth telluride - Bi(2)Te(3)- and related compounds have recently attracted strong interest owing to the discovery of the topological insulator properties in many members of this family of materials. The few-quintuple films of these materials are particularly interesting from the physics point of view. We report results of the micro-Raman spectroscopy study of the "graphene-like" exfoliated few-quintuple layers of Bi(2)Te(3), Bi(2)Se(3) and Sb(2)Te(3). It is found that crystal symmetry breaking in few-quintuple films results in appearance of A1u-symmetry Raman peaks, which are not active in the bulk crystals. The scattering spectra measured under the 633-nm wavelength excitation reveals a number of resonant features, which could be used for analysis of the electronic and phonon processes in these materials. In order to elucidate the influence of substrates on the few-quintuple-thick topological insulators we examined the Raman spectra of these films placed on mica, sapphire and hafnium-oxide substrates. The obtained results help to understand the physical mechanisms of Raman scattering in the few-quintuple-thick films and can be used for nanometrology of topological insulator films on various substrates.

PASCal: A principal-axis strain calculator for thermal expansion and compressibility determination

Abstract: We describe a web-based tool (PASCal; Principal Axis Strain Calculator) aimed at simplifying the determination of principal coefficients of thermal expansion and compressibilities from variable-temperature and variable-pressure lattice parameter data. In a series of three case studies, we use PASCal to re-analyse previously-published lattice parameter data and show that additional scientific insight is obtainable in each case. First, the two-dimensional metal-organic framework Cu-SIP-3 is found to exhibit the strongest area-negative thermal expansion (NTE) effect yet observed; second, the widely-used explosive HMX exhibits much stronger mechanical anisotropy than had previously been anticipated, including uniaxial NTE driven by thermal changes in molecular conformation; and, third, the high-pressure form of the mineral malayaite is shown to exhibit a strong negative linear compressibility (NLC) effect that arises from correlated tilting of SnO6 and SiO4 coordination polyhedra.

Magnetic Properties of Single Transition-Metal Atom Absorbed Graphdiyne and Graphyne Sheet

Abstract: The electronic and magnetic properties of single 3d transition-metal(TM) atom (V, Cr, Mn, Fe, Co, and Ni) adsorbed graphdiyne (GDY) and graphyne (GY) are systematically studied using first-principles calculations within the density functional framework. We find that the adsorption of TM atom not only efficiently modulates the electronic structures of GDY/GY system, but also introduces excellent magnetic properties, such as half-metal and spin-select half-semiconductor. Such modulation originates from the charge transfer between TM adatom and the GDY/GY sheet as well as the electron redistribution of the TM intra-atomic s, p, and d orbitals. Our results indicate that the TM adsorbed GDY/GY are excellent candidates for spintronics.

Tuning the Gate Opening Pressure of Metal Organic Frameworks (MOFs) for the Selective Separation of Hydro-carbons

Abstract: Separation of hydrocarbons is one of the most energy demanding processes. The need to develop materials for the selective adsorption of hydrocarbons, under reasonable conditions, is therefore of paramount importance. This work unveils unexpected hydrocarbon selectivity in a flexible Metal Organic Framework (MOF), based on differences in their gate opening pressure. We show selectivity dependence on both chain length and specific framework-gas interaction. Combining Raman spectroscopy and theoretical van der Waals Density Functional (vdW-DF) calculations, the separation mechanisms governing this unexpected gate opening behavior are revealed.

Resonant Elastic Soft X-Ray Scattering

Abstract: Resonant (elastic) soft x-ray scattering (RSXS) offers a unique element, site, and valence specific probe to study spatial modulations of charge, spin, and orbital degrees of freedom in solids on the nanoscopic length scale It cannot only be used to investigate single crystalline materials This method also enables to examine electronic ordering phenomena in thin films and to zoom into electronic properties emerging at buried interfaces in artificial heterostructures During the last 20 years, this technique, which combines x-ray scattering with x-ray absorption spectroscopy, has developed into a powerful probe to study electronic ordering phenomena in complex materials and furthermore delivers important information on the electronic structure of condensed matter This review provides an introduction to the technique, covers the progress in experimental equipment, and gives a survey on recent RSXS studies of ordering in correlated electron systems and at interfaces

Aluminum nitride as a new material for chip-scale optomechanics and nonlinear optics

Abstract: Silicon photonics has offered a versatile platform for the recent development of integrated optomechanical circuits However, silicon is limited to wavelengths above 1100 nm and does not allow device operation in the visible spectrum range where low noise lasers are conveniently available The narrow band gap of silicon also makes silicon optomechanical devices susceptible to strong two-photon absorption and free carrier absorption, which often introduce strong thermal effect that limit the devices' stability and cooling performance Further, silicon also does not provide the desired lowest order optical nonlinearity for interfacing with other active electrical components on a chip On the other hand, aluminum nitride (AlN) is a wideband semiconductor widely used in micromechanical resonators due to its low mechanical loss and high electromechanical coupling strength Here we report the development of AlN-on-silicon platform for low loss, wideband optical guiding, as well as its use for achieving simultaneous high optical quality and mechanical quality optomechanical devices Exploiting AlN's inherent second order nonlinearity we further demonstrate electro-optic modulation and efficient second-harmonic generation in AlN photonic circuits Our results suggest that low cost AlN-on-silicon photonic circuits are excellent substitutes for CMOS-compatible photonic circuits for building new functional optomechanical devices that are free from carrier effects

Single-layer MoS2 as efficient photocatalyst

Abstract: The potential application of the single-layer MoS2 as photocatalyst was revealed in this work based on first-principles calculations. It is found that the pristine single-layer MoS2 is a good candidate for photocatalyst, and its catalyzing ability can be tuned by the applied mechanical strain. Furthermore, the p-type doping could improve the catalyzing ability more efficiently: first, the p-type doping makes the direct transition of electron from valence band maximum (VBM) to conduction band minimum (CBM) viable; second, it separates the water splitting reaction sites by having reduction in Mo sites and oxidation in P dopant sites; third, it improves the efficiency by equalizing the reducing power {\Delta}1 and oxidizing power {\Delta}2, as well as by enhancing the light absorption in long wavelength end of the visible light. Thus enables the single-layer MoS2 to be a efficient visible-light photocatalyst.