Showing papers in "Curved and Layered Structures in 2016"

Abstract: Abstract In the present manuscript, free vibration response of circular cylindrical shells with functionally graded material (FGM) is investigated. The method of discrete singular convolution (DSC) is used for numerical solution of the related governing equation of motion of FGM cylindrical shell. The constitutive relations are based on the Love’s first approximation shell theory. The material properties are graded in the thickness direction according to a volume fraction power law indexes. Frequency values are calculated for different types of boundary conditions, material and geometric parameters. In general, close agreement between the obtained results and those of other researchers has been found.

Abstract: Abstract A Fourier-Ritz method for predicting the free vibration of composite laminated circular panels and shells of revolution subjected to various combinations of classical and non-classical boundary conditions is presented in this paper. A modified Fourier series approach in conjunction with a Ritz technique is employed to derive the formulation based on the first-order shear deformation theory. The general boundary condition can be achieved by the boundary spring technique in which three types of liner and two types of rotation springs along the edges of the composite laminated circular panels and shells of revolution are set to imitate the boundary force. Besides, the complete shells of revolution can be achieved by using the coupling spring technique to imitate the kinematic compatibility and physical compatibility conditions of composite laminated circular panels at the common meridian with θ = 0 and 2π. The comparisons established in a sufficiently conclusive manner show that the present formulation is capable of yielding highly accurate solutions with little computational effort. The influence of boundary and coupling restraint parameters, circumference angles, stiffness ratios, numbers of layer and fiber orientations on the vibration behavior of the composite laminated circular panels and shells of revolution are also discussed.

Abstract: Abstract The present paper shows an innovative multirotor Unmanned Aerial Vehicle (UAV) which is able to easily and quickly change its configuration. In order to satisfy this feature, the principal structure is made of an universal plate, combined with a circular ring, to create a rail guide able to host the arms, in a variable number from 3 to 8, and the legs. The arms are adjustable and contain all the avionic and motor drivers to connect the main structure with each electric motor. The unique arm design, defined as all-in-one, allows classical single rotor configurations, double rotor configurations and amphibious configurations including inflatable elements positioned at the bottom of the arms. The proposed multi-rotor system is inexpensive because of the few universal pieces needed to compose the platform which allows the creation of a kit. This modular kit allows to have a modular drone with different configurations. Such configurations are distinguished among them for the number of arms, number of legs, number of rotors and motors, and landing capability. Another innovation feature is the introduction of the 3D printing technology to produce all the structural elements. In this manner, all the pieces are designed to be produced via the Fused Deposition Modelling (FDM) technology using desktop 3D printers. Therefore, an universal, dynamic and economic multi-rotor UAV has been developed.

Abstract: Abstract The Fused Deposition Modelling (FDM) technology is widely used in rapid prototyping. 3D printers for home desktop applications are usually employed to make non-structural objects. When the mechanical stresses are not excessive, this technology can also be successfully employed to produce structural objects, not only in prototyping stage but also in the realization of series pieces. The innovative idea of the present work is the application of this technology, implemented in a desktop 3D printer, to the realization of components for aeronautical use, especially for unmanned aerial systems. For this purpose, the paper is devoted to the statistical study of the performance of a desktop 3D printer to understand how the process performs and which are the boundary limits of acceptance. Mechanical and geometrical properties of ABS (Acrylonitrile Butadiene Styrene) specimens, such as tensile strength and stiffness, have been evaluated. ASTM638 type specimens have been used. A capability analysis has been applied for both mechanical and dimensional performances. Statistically stable limits have been determined using experimentally collected data.

Abstract: In the present paper, a General Algorithm is applied to the analysis of high-rise structures. This algorithm is to be used as a calculation tool in preliminary design; it allows to define the interaction between closed and open, straight or curved shear-walls, and the forces exchanged in structures subject to mainly horizontal loads. The analysis can be performed in both static and dynamic regimes, the mode shapes and the natural frequencies being assessed. This general formulation allows analyses of high-rise structures by taking into account the torsional rigidity and the warping deformations of the elements composing the building without gross simplifications. In thisway it is possible to model the structure as a single equivalent cantilever, thus minimising the degrees of freedom of the system, and consequently the calculation time. Finally, potentials of the method proposed are demonstrated by a numerical example which emphasizes the link between global displacements and stresses in the elements composing the structure.

Abstract: Abstract In the present study non-linear free vibration analysis is performed on a tapered Axially Functionally Graded (AFG) beam resting on an elastic foundation with different boundary conditions. Firstly the static problem is carried out through an iterative scheme using a relaxation parameter and later on the subsequent dynamic problem is solved as a standard eigen value problem. Minimum potential energy principle is used for the formulation of the static problem whereas for the dynamic problem Hamilton’s principle is utilized. The free vibrational frequencies are tabulated for different taper profile, taper parameter and foundation stiffness. The dynamic behaviour of the system is presented in the form of backbone curves in dimensionless frequency-amplitude plane.

Abstract: Abstract Bases of asymptotic theory of beams, plates and shells are stated. The comparison with classic theory is conducted. New classes of thin bodies problems, for which hypotheses of classic theory are not applicable, are considered. By the asymptotic method effective solutions of these problems are obtained. The effectiveness of the asymptotic method for finding solutions of as static, as well as dynamic problems of beams, plates and shells is shown.

Abstract: Abstract In this work the attention is focused to the numerical simulation of the experimental bending tests carried out on a total of six reinforced concrete r.c. plates the latter aimed to provide a basic understanding of the its performance when strengthened by Fiber Reinforced Cementitius Matrix (FRCM) Composites. Three of those were used as control specimens. The numerical simulation was carried out by LUSAS software. A good correlation between the FE results and data obtained from the test, both in the load–deformation behavior and the failure load was highlighted. This permits to prove that applied strengthening system gives back an enhancement 2.5 times greater in respect of the unreinforced case. A greater energy dissipation ability and a residual load-bearing capacity makes the proposed system very useful in the retrofitting as well as in the case of strengthening of bridge structures. Based on the validation of the FE results in bending, the numerical analysis was also extended to characterize the behavior of this strengthening system in tensile.

Abstract: Abstract The second order statistics of mixed mode stress intensity factors (MSIF) of single edge V-notched angle ply laminated composite plate subjected to uniaxial tensile load with uncertinity in the system properties using displacement correlation method (DCM) is evaluated. The random system properties such as material properties, crack opening and crack length are modelled as combined uncorrelated and correlated random system variables. A C0 finite element method (FEM) based on higher order shear deformation plate theory (HSDT) is used for basic formulation. The Taylor series based first order perturbation technique (FOPT), second order perturbation technique (SOPT) are used and direct Monte Carlo simulation (MCS) is performed to evaluate the statistics (mean and coefficient of variance) of the mixed mode SIFs. The present work signifies the accurate analysis of frature behaviour by influence of different random variables and fibre orientations on the fracture behaviour in angle ply laminates.

Abstract: Abstract In this paper, the buckling load optimisation is performed on sandwich cylindrical panels. A finite element program is developed in MATLAB to solve the governing differential equations of the global buckling of the structure. In order to find the optimal solution, the genetic algorithm Toolbox in MATLAB is implemented. Verifications are made for both the buckling finite element code and also the results from the genetic algorithm by comparisons to the results available in literature. Sandwich cylindrical panels are optimised for the buckling strength with isotropic or orthotropic cores with different boundary conditions. Results are presented in terms of stacking sequence of fibers in the face sheets and core to face sheet thickness ratio.

Abstract: Abstract This paper deals with the study of transverse vibrations in piezothermoelastic beam resonators with fractional order derivative. The fractional order theory of thermoelasticity developed by Sherief et al. [1] has been used to study the problem. The expressions for frequency shift and damping factor are derived for a thermo micro-electromechanical (MEM) and thermo nano-electromechanical (NEM) beam resonators clamped on one side and free on another. The effect of fractional order derivative on the derived expressions is observed analytically and shown graphically in the case of Lead Zirconate Titanate (PZT)-5A material. For α = 1, our results agree with those that are obtained by Grover and Sharma [20] and other particular cases of interest are also discussed.

Abstract: Abstract Inclined, shallow, elastic cables under static 3D loads, arbitrarily distributed, are studied. Cables having natural length both larger or smaller than the distance between the supports (i.e. suspended or taut cables, respectively), are considered. Kinematically exact equations are derived, and projected onto an orthonormal basis intrinsic to the chord. A perturbation procedure is proposed, which extrapolates the solution relevant to the taut string, up to the desired order, and leads to a closed-form solution. Lower-order solutions are consistent with the hypotheses normally adopted in technical environment. Emphasis is given to the mechanical interpretation of the cable behavior. The asymptotic solution is compared to the explicit (not in closed-form) solution of the literature.

Abstract: Abstract In the critical state of a beam under central compression a flexural-torsional equilibrium shape becomes possible in addition to the fundamental straight equilibrium shape and the Euler bending. Particularly, torsional configuration takes place in all cases where the line of shear centres does not correspond with the line of centres of mass. This condition is obtained here about a z-axis highly variable section beam; with the assumptions that shear centres are aligned and line of centres is bound to not deform. For the purpose, let us evaluate an open thin wall C-cross section with flanges width and web height linearly variables along z-axis in order to have shear centres axis approximately aligned with gravity centres axis. Thus, differential equations that govern the problem are obtained. Because of the section variability, the numerical integration of differential equations that gives the true critical load is complex and lengthy. For this reason, it is given an energetic formulation of the problem by the theorem of minimum total potential energy (Ritz-Rayleigh method). It is expected an experimental validation that proposes the model studied.

Abstract: Abstract Two type of numerical approach namely, Radial Basis Function and Spline approximation, used to analyse the free vibration of anti-symmetric angle-ply laminated plates under clamped boundary conditions. The equations of motion are derived using YNS theory under first order shear deformation. By assuming the solution in separable form, coupled differential equations obtained in term of mid-plane displacement and rotational functions. The coupled differential is then approximated using Spline function and radial basis function to obtain the generalize eigenvalue problem and parametric studies are made to investigate the effect of aspect ratio, length-to-thickness ratio, number of layers, fibre orientation and material properties with respect to the frequency parameter. Some results are compared with the existing literature and other new results are given in tables and graphs.

Abstract: Abstract Nonlinear dynamic behavior of fixed-fixed shallow and deep curved beams is studied experimentally using non-contact type of electromagnetic shaker and acceleration measurements. The frequency response obtained from acceleration measurements is found to be in fairly good agreement with the computational response. The travellingwave phenomenon along with participation of higher harmonics and softening nonlinearity are observed. The experimental results on the internal resonance of curved beams due to direct excitation of anti-symmetric mode are reported for the first time. The deep curved beam depicts chaotic response at higher excitation amplitude.

Abstract: Abstract The analysis of monolithic and sandwich plates is illustrated for those cases where the boundary conditions are not uniform along the thickness direction, and run at a given position along the thickness direction. For instance, a sandwich plate constrained at the bottom or top face can be considered. The approach relies upon a sublaminate formulation,which is applied here in the context of a Ritz-based approach. Due to the possibility of dividing the structure into smaller portions, viz. the sublaminates, the constraints can be applied at any given location, providing a high degree of flexibility in modeling the boundary conditions. Penalty functions and Lagrange multipliers are introduced for this scope. Results are presented for free-vibration and bending problems. The close matching with highly refined finite element analyses reveals the accuracy of the proposed formulation in determining the vibration frequencies, as well as the internal stress distribution. Reference results are provided for future benchmarking purposes.

Abstract: Abstract This paper deals with the dynamic behavior of curved-in-plane bridges where the effect of the bridge curvature radius, the moving load (vehicle) speed, the truck cant angle, the deck surface conditions and, mainly, the response accuracy depending on the vehicle model used are investigated. Besides the above parameters, the influence of several loading models is studied as well, especially the models of a concentrated load, a damped mass-load, a sequence of two concentrated loads and a real vehicle aswell as a damped vehicle,where its width is taken into account. A 3-DOF model is considered for the analysis of the bridge, while the theoretical formulation is based on a continuum approach, which has been widely used in the literature to analyze such bridges.

Abstract: Abstract A review of literature reveals that bending analysis of laminated composite stiffened hypar shells with cutout have not received due attention. Being a doubly ruled surface, a skewed hypar shell fulfils aesthetic as well as ease of casting requirements. Further, this shell allows entry of north light making it suitable as civil engineering roofing units. Hypar shell with cutout subjected to uniformly distributed load exhibits improved performances with stiffeners. Hence relative performances of antisymmetric angle-ply laminated composite stiffened hypar shells in terms of displacements and stress resultants are studied in this paper under static loading. A curved quadratic isoparametric eight noded element and three noded beam elements are used to model the shell surface and the stiffeners respectively. Results obtained from the present study are compared with established ones to check the correctness of the present approach. A number of additional problems of antisymmetric angle-ply laminated composite stiffened hypar shells are solved for various fibre orientations, number of layers and boundary conditions. Results are interpreted from practical application standpoints and findings important for a designer to decide on the shell combination among a number of possible options are highlighted.

Abstract: Abstract The aim of this study was to show the influence of locational states of submicron fibers added into epoxy matrix on mechanical properties of modified plane-woven carbon fiber reinforced plastic (CFRP). To change the locational states of submicron fibers, two kinds of fabrication processes were applied in preparing specimen by hand lay-up method. Submicron fibers were simply added into epoxy resin with ethanol after they were stirred by a dispersion process using homogenizer to be located far from the interface between reinforcement and matrix. In contrast, submicron fibers were attached onto the carbon fibers by injecting from a spray nozzle accompanying with ethanol to be located near the interface, after they were tentatively contained in ethanol. The plain-woven CFRP plates were fabricated by hand lay-up method and cured at 80 degree-C for 1 hour and then at 150 degree-C for 3 hours. After curing, the plain-woven CFRP plates were cut into the dimension of specimen. Tensile shear strength and Mode-II fracture toughness of CFRP were determined by tensile lap-shear test and End-notched flexure(ENF) test, respectively. When submicron fibers were located far from the interface between carbon fibers and epoxy resin, tensile shear strength and Mode-II fracture toughness of CFRP were improved 30% and 18% compared with those of unmodified case. The improvement ratio in modified case was rather low (about few percentages) in the case where submicron fibers were located near the interface. The result suggested that crack propagation should be prevented when submicron fibers were existed far from the interface due to the effective stress state around the crack tip.

Abstract: Abstract One of the main goal in aircraft structures designing isweight decreasing and stiffness increasing. Composite structures recently became popular in aircraft because of their mechanical properties and wide range of optimization possibilities.Weight distribution and lay-up are keys to creating lightweight stiff strictures. In this paperwe discuss optimization of specific structure that undergoes the non-uniform air pressure at the different flight conditions and reduce a level of noise caused by the airflowinduced vibrations at the constrained weight of the part. Initial model was created with CAD tool Siemens NX, finite element analysis and post processing were performed with COMSOL Multiphysicsr and MATLABr. Numerical solutions of the Reynolds averaged Navier-Stokes (RANS) equations supplemented by k-w turbulence model provide the spatial distributions of air pressure applied to the shell surface. At the formulation of optimization problem the global strain energy calculated within the optimized shell was assumed as the objective. Wall thickness has been changed using parametric approach by an initiation of auxiliary sphere with varied radius and coordinates of the center, which were the design variables. To avoid a local stress concentration, wall thickness increment was defined as smooth function on the shell surface dependent of auxiliary sphere position and size. Our study consists of multiple steps: CAD/CAE transformation of the model, determining wind pressure for different flow angles, optimizing wall thickness distribution for specific flow angles, designing a lay-up for optimal material distribution. The studied structure was improved in terms of maximum and average strain energy at the constrained expense ofweight growth. Developed methods and tools can be applied to wide range of shell-like structures made of multilayered quasi-isotropic laminates.