Showing papers in "Journal of Materials Research in 2006"

Mechanical properties of nacre constituents and their impact on mechanical performance

Abstract: The mechanical properties of nacre constituents from red abalone were investigated. Electron microscopy studies revealed that the tablets are composed of single-crystal aragonite with nanograin inclusions. Both nanoasperities and aragonite bridges are present within the interfaces between the tablets. By means of nanoindentation and axial compression tests, we identified single tablet elastic and inelastic properties. The elastic properties are very similar to those of single-crystal aragonite. However, their strength is higher than previously reported values for aragonite. A finite element model of the interface accounting for nanoasperities and the identified properties revealed that the nanoasperities are strong enough to withstand climbing and resist tablet sliding, at least over the initial stages of deformation. Furthermore, it was observed that the model over-predicts strength and under-predicts ductility. Therefore, we conclude that other interface features must be responsible for the enhanced performance of nacre over its constituents.

Atomistic and continuum modeling of mechanical properties of collagen: Elasticity, fracture, and self-assembly

Abstract: We report studies of the mechanical properties of tropocollagen molecules under different types of mechanical loading including tension, compression, shear, and bending. Our modeling yields predictions of the fracture strength of single tropocollagen molecules and polypeptides, and also allows for quantification of the interactions between tropocollagen molecules. Atomistic modeling predicts a persistence length of tropocollagen molecules ξ ≈ 23.4 nm, close to experimental measurements. Our studies suggest that to describe large-strain or hyperelastic properties, it is critical to include a correct description of the bond behavior and breaking processes at large bond stretch, information that stems from the quantum chemical details of bonding. We use full atomistic calculations to derive parameters for a mesoscopic bead-spring model of tropocollagen molecules. We demonstrate that the mesoscopic model enables one to study the finite temperature, long-time scale behavior of tropocollagen fibers, illustrating the dynamics of solvated tropocollagen molecules for different molecular lengths.

Monolithic nanoporous copper by dealloying Mn–Cu

Abstract: Monolithic nanoporous copper was synthesized by dealloying Mn0.7Cu0.3 by two distinct methods: potentiostatically driven dealloying and free corrosion. Both the ligament size and morphology were found to be highly dependent on the dealloying methods and conditions. For example, ligaments from 16 nm–125 nm were obtained by dealloying either electrochemically or by free corrosion, respectively. Optimization of the starting Mn–Cu alloy microstructure allowed us to synthesize uniform porous structures; but we found cracking to be unavoidable. Despite the presence of unavoidable defects, the nanoporous material still exhibits higher than expected yield strength.

Sliding wear, viscoelasticity, and brittleness of polymers

Abstract: We have connected viscoelastic recovery (healing) in sliding wear to free volume in polymers by using pressure-volume-temperature (P-V-T) results and the Hartmann equation of state. A linear relationship was found for all polymers studied with a wide variety of chemical structures, except for polystyrene (PS). Examination of the effect of the indenter force level applied in sliding wear on the healing shows that recovery is practically independent of that level. Strain hardening in sliding wear was observed for all materials except PS, the exception attributed to brittleness. Therefore, we have formulated a quantitative definition of brittleness in terms of elongation at break and storage modulus. Further, we provide a formula relating the brittleness to sliding wear recovery; the formula is obeyed with high accuracy by all materials including PS. High recovery values correspond to low brittleness, and vice versa. Our definition of brittleness can be used as a design criterion for choosing polymers for specific applications.

Contact creep compliance of viscoelastic materials via nanoindentation

Abstract: The creep compliance of viscoelastic materials such as synthetic polymers is an established metric of the rate at which strain increases for a constant applied stress and can, in principle, be implemented at the nanoscale to compare quantitatively bulk or thin film polymers of different structures or processing histories. Here, we outline the evolution of contact creep compliance analysis and application for both conical and spherical indenter geometries. Through systematic experiments on four amorphous (glassy) polymers, two semi-crystalline polymers and two epoxies, we show that assumptions of linear viscoelasticity are not maintained for any of these polymers when creep compliance is measured via conical indentation at the nanoscale, regardless of the rate of stress application (step or ramp). Further, we show that these assumptions can be maintained to evaluate the contact creep compliance Jc(t) of these bulk polymers, regardless of the rate of stress application, provided that the contact strains are reduced sufficiently through spherical indentation. Finally, we consider the structural and physical properties of these polymers in relation to Jc(t), and demonstrate that Jc(t) correlates positively with molecular weight between entanglements or crosslinks of bulk, glassy polymers.

Cellulose micro/nanocrystals reinforced polyurethane

Abstract: Nano- and micron-sized cellulose crystals were prepared and utilized as reinforcements for polyurethane composites. The cellulose crystals obtained from microcrystalline cellulose (MCC) were incorporated into a polar organic solvent, dimethylformamide (DMF), and ultrasonicated to obtain a stable suspension. The suspension was an effective means for incorporating the cellulose crystals into the polyol-isocyanate mixture, utilized to produce polyurethane composite films. The use of DMF presents an interesting alternative for the use of cellulose crystals as reinforcement of a broad new range of polymers. Moreover, the rheology of the uncured liquid suspensions was investigated, and analysis of the results indicated the formation of a filler structure pervading the liquid suspension. Besides, films were prepared by casting and thermal curing of the stable suspensions. Thermomechanical and mechanical testing of the films were carried out to analyze the performance of the composites. The results indicated that a strong filler-matrix interaction was developed during curing as a result of a chemical reaction occurring between the crystals and the isocyanate component.

Mesoscale modeling of mechanics of carbon nanotubes: Self-assembly, self-folding, and fracture

Abstract: Using concepts of hierarchical multiscale modeling, we report development of a mesoscopic model for single-wall carbon nanotubes with parameters completely derived from full atomistic simulations. The parameters in the mesoscopic model are fit to reproduce elastic, fracture, and adhesion properties of carbon nanotubes, in this article demonstrated for (5,5) carbon nanotubes. The mesoscale model enables modeling of the dynamics of systems with hundreds of ultralong carbon nanotubes over time scales approaching microseconds. We apply our mesoscopic model to study self-assembly processes, including self-folding, bundle formation, as well as the response of bundles of carbon nanotubes to severe mechanical stimulation under compression, bending, and tension. Our results with mesoscale modeling corroborate earlier results, suggesting a novel self-folding mechanism, leading to creation of racket-shaped carbon nanotube structures, provided that the aspect ratio of the carbon nanotube is sufficiently large. We find that the persistence length of the (5,5) carbon nanotube is on the order of a few micrometers in the temperature regime from 300 to 1000 K.

Spherical indentation load-relaxation of soft biological tissues

Abstract: Elastic-viscoelastic correspondence was used to generate displacement–time solutions for spherical indentation testing of soft biological materials with time-dependent mechanical behavior. Boltzmann hereditary integral operators were used to determine solutions for indentation load-relaxation following a constant displacement rate ramp. A “ramp correction factor” approach was used for routine analysis of experimental load-relaxation data. Experimental load-relaxation tests were performed on rubber, as well as kidney tissue and costal cartilage, two hydrated soft biological tissues with vastly different mechanical responses. The experimental data were fit to the spherical indentation ramp-relaxation solutions to obtain values of short- and long-time shear modulus and of material time constants. The method is used to demonstrate linearly viscoelastic responses in rubber, level-independent indentation results for costal cartilage, and age-independent indentation results for kidney parenchymal tissue.

Micromechanical properties of biological silica in skeletons of deep-sea sponges

Abstract: The silica skeleton of the deep-sea sponge Euplectella aspergillum was recently shown to be structured over at least six levels of hierarchy with a clear mechanical functionality. In particular, the skeleton is built of laminated spicules that consist of alternating layers of silica and organic material. In the present work, we investigated the micromechanical properties of the composite material in spicules of Euplectella aspergillum and the giant anchor spicule of Monorhaphis chuni. Organic layers were visualized by backscattered electron imaging in the environmental scanning electron microscope. Raman spectroscopic imaging showed that the organic layers are protein-rich and that there is an OH-enrichment in silica near the central organic filament of the spicule. Small-angle x-ray scattering revealed the presence of nanospheres with a diameter of only 2.8 nm as the basic units of silica. Nanoindentation showed a considerably reduced stiffness of the spicule silica compared to technical quartz glass with different degrees of hydration. Moreover, stiffness and hardness were shown to oscillate as a result of the laminate structure of the spicules. In summary, biogenic silica from deep-sea sponges has reduced stiffness but an architecture providing substantial toughening over that of technical glass, both by structuring at the nanometer and at the micrometer level.

Mechanical response of human red blood cells in health and disease: Some structure-property-function relationships

Abstract: Aspects of mechanical deformability and biorheology of the human red blood cell are known to play a pivotal role in influencing organ function as well as states of overall health and disease. In this article, consequences of alterations to the membrane and cytoskeletal molecular structure of the human red blood cell are considered in the context of an infectious disease, Plasmodium falciparum malaria, and several hereditary hemolytic disorders: spherocytosis, elliptocytosis, and sickle cell anemia. In each of these cases, the effects of altered cell shape or molecular structure on cell elasticity, motility, and biorheology are examined. These examples are used to gain broad perspectives on the connections among cell and subcellular structure, properties, and disease at the intersections of engineering, biology, and medicine.

Boron nitride nanotubes/polystyrene composites

Abstract: Boron nitride nanotube (BNNT)/polystyrene (PS) composite films were fabricated for the first time using high-quality BNNTs synthesized via a chemical-vapor-deposition method. The composite films exhibited good transparency. Tensile tests indicated that the elastic modulus of the films was increased by ∼21% when a ∼1 wt% soluble BNNT fraction was in use. Dispersion of BNNTs in PS and interfacial interactions between them were investigated using transmission electron microscopy. The film thermal properties, such as stability to oxidation and glass transition temperatures were measured. The experimental results and simple theoretical estimates indicate that BNNTs is a promising additive material for polymeric composites.

Mechanical modulation at the lamellar level in osteonal bone

Abstract: The secondary osteon is the fundamental building block of compact cortical bone at the tissue level. Light and scanning electron microscopy have shown that the osteon consists of a laminated cylindrical composite of mineralized collagen fibril lamellae ∼5–7 μm thick. Using scanning nanoindentation and quantitative backscattered electron imaging on secondary osteons from the human femoral midshaft, we found that the indentation modulus shows a periodic variation between ∼24 GPa and ∼27 GPa within a single lamella. The average lamellar value remains nearly constant across the osteon and increases abruptly to more than 30 GPa at the interstitial bone interface. The local mineral content, determined from quantitative backscattered electron imaging at the indented locations, shows also a lamellar level modulation and is positively correlated with the indentation modulus at the same tissue position. We propose that such a mechanically and compositionally modulated structure may be an effective crack-stopping mechanism in bone.

On the determination of spherical nanoindentation stress-strain curves

Abstract: Instrumented nanoindentation experiments, especially with sharp tips, are a well-established technique to measure the hardness and moduli values of a wide range of materials. However, and despite the fact that they can accurately delineate the onset of the elasto-plastic transition of solids, spherical nanoindentation experiments are less common. In this article we propose a technique in which we combine (i) the results of continuous stiffness measurements with spherical indenters–with radii of 1 μm and/or 13.5 μm, (ii) Hertzian theory, and (iii) Berkovich nanoindentations, to convert load/depth of indentation curves to their corresponding indentation stress–strain curves. We applied the technique to fused silica, aluminum, iron and single crystals of sapphire and ZnO. In all cases, the resulting indentation stress–strain curves obtained clearly showed the details of the elastic-to-plastic transition (i.e., the onset of yield, and, as important, the steady state hardness values that were comparable with the Vickers microhardness values obtained on the same surfaces). Furthermore, when both the 1 μm and 13.5 μm indenters were used on the same material, for the most part, the indentation stress–strain curves traced one trajectory. The method is versatile and can be used over a large range of moduli and hardness values.

Hybrid carbon nanotubes : Strategy, progress, and perspectives

Abstract: We introduce the concept of meta-nanotubes, among which are hybrid carbon nanotubes (X@CNTs), which are CNTs whose hollow core is filled—fully or partially—with foreign atoms, molecules, or compounds. The article focuses on the latter, describing their potential interest and the various ways currently available to synthesize them, while providing examples of the resulting materials mainly taken from the author’s works but also from literature, as characterized by means of high-resolution microscopy and related techniques. We discuss advantages and drawbacks of the various synthesis routes to help willing scientists and engineers to define a strategy for X@CNT synthesis with respect to their specific goals and expectations. Some examples of peculiar properties and behaviors of X@CNTs will be provided as well, although such related investigations are still scarcely reported because we are dealing with quite new nanomaterials.

Nanoindentation and contact-mode imaging at high temperatures

Abstract: Technical issues surrounding the use of nanoindentation at elevated temperatures are discussed, including heat management, thermal equilibration, instrumental drift, and temperature-induced changes to the shape and properties of the indenter tip. After characterizing and managing these complexities, quantitative mechanical property measurements are performed on a specimen of standard fused silica at temperatures up to 405 °C. The extracted values of hardness and Young’s modulus are validated against independent experimental data from conventional mechanical tests, and accuracy comparable to that obtained in standard room-temperature nanoindentation is demonstrated. In situ contact-mode images of the surface at temperature are also presented.

Novel technique for measuring the mechanical properties of porous materials by nanoindentation

Abstract: A new technique for measuring the elastic-plastic properties of porous thin films by means of nanoindentation is proposed. The effects of porosity on indentation hardness and modulus are investigated through finite element analyses based on the Gurson model for plastic deformation of ductile porous materials. Intrinsic mechanical properties of the thin film are obtained by eliminating both substrate and densification effects. The technique is applied to the special case of a porous, low-permittivity dielectric thin film. The results are in good agreement with those obtained independently using the plane-strain bulge test.

Localized heating and fracture criterion for bulk metallic glasses

Abstract: In this study, we demonstrated that the failure of bulk metallic glasses (BMGs) results from a sudden temperature rise within a shear band. Using a shear transformation zone model, we successfully calculated the temperature within a shear band and found it consistent with the observation from an in situ infrared thermographic system. The instantaneous temperature within a shear band at fracture agrees remarkably well with the glass transition temperature (Tg providing a new criterion to determine the strength of BMGs from their Tg. This agreement also discloses the fact that catastrophic failure of BMG is caused by the sudden drop in viscosity inside the shear band when the instantaneous temperature within a shear band approaches Tg.

Novel metallurgical process for titanium production

Abstract: In this work, a consumable anode composed of a solid solution of titanium carbide and titanium monoxide was prepared via carbothermic reduction of TiO2. Upon electrolysis, the anode fed Ti2+ into solution and carbon monoxide was generated; no excess carbon remained to contaminate the melt. On the cathode, high-purity titanium (>99.9%) was produced. Our results suggest anode and cathode current efficiencies of 93.5% and 89% respectively, indicating that the method is viable and extremely cost-effective, potentially dropping the cost of titanium to near that of aluminum.

The mechanical properties of freestanding electroplated Cu thin films

Abstract: The plane-strain bulge test is used to investigate the mechanical behavior of freestanding electroplated Cu thin films as a function of film thickness and microstructure. The stiffness of the films increases slightly with decreasing film thickness because of changes in the crystallographic texture and the elastic anisotropy of Cu. Experimental stiffness values agree well with values derived from single-crystal elastic constants and the appropriate orientation distribution functions. No modulus deficit is observed. The yield stress of the films varies with film thickness and heat treatment as a result of changes in the grain size of the films. The yield stress follows typical Hall-Petch behavior if twins are counted as distinct grains, indicating that twin boundaries are effective barriers to dislocation motion. The Hall-Petch coefficient is in good agreement with values reported for bulk Cu. Film thickness and crystallographic texture have a negligible effect on the yield stress of the films.

Nanomechanical properties of nacre

Abstract: Nacre, the inner iridescent layer of seashells is a model biomimetic system composed of 95% of inorganic (aragonite) phase and 5% of organic phase. Nacre exhibits an interlocked layered “brick and mortar” structure where the bricks are made up of aragonitic calcium carbonate and mortar is an organic phase. Here, we report the role of indentation load and penetration depth on measurement of nanomechanical properties of nacre. A range of loads from 10 μN to 10,000 μN were applied to obtain the response from different depths of nacre. The values of hardness and elastic modulus decrease with increasing load (i.e., increase in penetration depth). The variation in these values is significant at lower loads and decreases with increase in indentation load. From our results, it appears that the nanoindentation tests done at lower loads are highly influenced by micro and nanostructure in nacre. The indentation experiments performed at low loads indicate an elastic modulus of about 15 GPa for the organic phase. The low load, low penetration experiments appear to be better indicators of nanomechanical behavior. Also, we have observed a step-like behavior in the load-displacement curves at high load indentations on nacre. These features are attributed to the organic layer between the aragonite platelets. The indentation tests with penetration depths more than ~250-300 nm often disrupt the organic layer and the behavior is not recovered in the unloading part of the curve. The microarchitecture and the composition of nacre contribute to the decrease in hardness values with increasing depth along with the indentation size effects.

Nanoscale control of silica morphology and three-dimensional structure during diatom cell wall formation

Abstract: We present a unique approach combining biological manipulation with advanced imaging tools to examine silica cell wall synthesis in the diatom Thalassiosira pseudonana. The innate capabilities of diatoms to form complex 3D silica structures on the nano- to micro-scale exceed current synthetic approaches because they use a fundamentally different formation process. Understanding the molecular details of the process requires identifying structural intermediates and correlating their formation with genes and proteins involved. This will aid in development of approaches to controllably alter structure, facilitating the use of diatoms as a direct source of nanostructured materials. In T. pseudonana, distinct silica morphologies were observed during formation of different cell wall substructures, and three different scales of structural organization were identified. At all levels, structure formation correlated with optimal design properties for the final product. These results provide a benchmark of measurements and new insights into biosilicification processes, potentially also benefiting biomimetic approaches.

Nanoindentation: Application to dental hard tissue investigations

Abstract: In the last decade, most publications on the mechanical properties of dental calcified tissues were based on nanoindentation investigation. This technique has allowed a better understanding of the mechanical behavior of enamel, dentin, and cementum at a nanoscale. The indentations are normally carried out using pointed or spherical indenters. Hardness and elastic modulus are measured as a function of indenter penetration depth and from the elastic recovery upon unloading. The unique microstructure of each calcified tissue significantly contributes to the variations in the mechanical properties measured. As complex hydrated biological composites, the relative proportions of the composite components, namely, inorganic material (hydroxyapatite), organic material, and water, determines the mechanical properties of the dental hard tissues. Many pathological conditions affecting dental hard tissues cause changes in mineral levels, crystalline structures, and mechanical properties that may be probed by nanoindentation. This review focuses on relevant nanoindentation techniques and their applications to enamel, dentin, and cementum investigations.

Nanosphere lithography fabricated plasmonic materials and their applications

Abstract: Nanosphere lithography fabricated nanostructures have highly tunable localized surface plasmons, which have been used for important sensing and spectroscopy applications. In this work, the authors focus on biological applications and technologies that utilize two types of related plasmonic phenomena: localized surface plasmon resonance (LSPR) spectroscopy and surface-enhanced Raman spectroscopy (SERS). Two applications of these plasmonic materials are presented: (i) the development of an ultrasensitive nanoscale optical biosensor based on LSPR wavelength-shift spectroscopy and (ii) the SERS detection of an anthrax biomarker.

Inorganic nanotubes and fullerene-like nanoparticles

Abstract: We have proposed in 1992 that nanoparticles of layered compounds will be unstable against folding and close into fullerene-like structures and nanotubes (IF). Nanotubes and fullerene-like structures were prepared from numerous compounds with layered and recently also non-layered structure by various groups. Much progress has been achieved in the synthesis of inorganic nanotubes and fullerene-like nanoparticles of WS2 and MoS2 and many other metal dichalcogenides over the last few years. Substantial progress has been accomplished in the use of such nanoparticles for tribological applications and lately for impact resilient nanocomposites. These tests indicated that IF-MoS2 and IF-WS2 are heading for large scale applications in the automotive, machining, aerospace, electronics, defense, medical and numerous other kinds of industries. A few products based on these nanoparticles have been recently commercialized by “ApNano Materials, Inc”. Novel applications of inorganic nanotubes and fullerene-like nanoparticles in the fields of catalysis; microelectronics; Li rechargeable batteries; medical and opto-electronics will be discussed.

Strong Zn concentration effect on the soldering reactions between Sn-based solders and Cu

Abstract: The acute Zn concentration sensitivity of the reaction between Sn-based solders and Cu substrate is reported and explained in this article. Three Sn-xZn solders (x = 0.5, 0.7, and 2 wt%) were reacted with Cu substrates at 250 °C for 2–10 min. A slight variation in the Zn concentration changed the reaction product formed at the interface. When the Zn concentration was low (x = 0.5 wt%), the reaction product was Cu6Sn5. When the Zn concentration was slightly increased to 2 wt%, the reaction product became Cu5Zn8. When Zn concentration was in-between (x = 0.7 wt%), Cu6Sn5 and CuZn co-existed. The above findings are explained using the Cu–Sn–Zn phase diagram. The implication is that the type of compound forms at the interface can be controlled by adjusting the Zn concentration of the Sn-based solders.

Hydration effects on the micro-mechanical properties of bone

Abstract: Bone is a composite material with hydroxyapatite mineral, collagen, and water as primary components. Water plays an important role in maintaining the mechanical integrity of the composite, but the manner in which water interacts within the collagen and mineral at ultrastructural length-scales is poorly understood. The current study examined changes in the mechanical properties of bone as a function of hydration state. Tissues were soaked in different solvents and solutions, with different polarities, to manipulate tissue hydration. Mineralized bone was characterized using nanoindentation creep tests for quantification of both the elastic and viscoelastic mechanical responses, which varied dramatically with tissue bathing solution. The results were considered within the context of solution physical chemistry. Selectively removing and then replacing water provided insights into the ultrastructure of the tissues via the corresponding changes in the experimentally determined mechanical responses.

Hardness and elastic properties of dehydrated cuticle from the lobster Homarus americanus obtained by nanoindentation

Abstract: The mechanical properties of biological materials are well adjusted to their function. An excellent example for such materials is the cuticle or exoskeleton of arthropods. In this study, dehydrated cuticle of the American lobster Homarus americanus was examined as a model for a mineralized biological composite material. Nanoindentation testing is a powerful method for revealing gradients and anisotropy in the hardness and the elastic properties of such materials. The air-dried test specimens stem from different parts of the crusher claw with different biological functions. Both the exocuticle and the endocuticle were probed in normal and in the transverse direction to the cuticle surface. For estimating variations in the grade of mineralization, the samples which were tested as cross-sections of the cuticle were analyzed by the use of energy dispersive x-ray mapping. The microstructure of fracture surfaces of the test specimens was investigated using scanning electron microscopy. Due to the use of dehydrated samples, our results do not reflect the exact properties of lobster cuticle in the natural hydrated state, but they can be regarded as a fairly good approximation to the in vivo state.

High glass-forming ability and good mechanical properties of new bulk glassy alloys in Cu–Zr–Ag ternary system

Abstract: The addition of Ag to Cu–Zr alloys is very effective for the increase in the stability of supercooled liquid as well as the glass-forming ability (GFA). The large supercooled liquid region (ΔTx) exceeding 60 K in Cu–Zr–Ag ternary system was obtained in a wide range of 25–55 at.% Cu, 40–65 at.% Zr, and 5–25 at.% Ag. The best GFA was obtained around Cu45Zr45Ag10, and glassy alloy rods with diameters up to 6.0 mm were formed by copper mold casting. The bulk glassy alloys exhibit good mechanical properties, i.e., compressive fracture strength of 1780–1940 MPa, Young’s modulus of 106–112 GPa, compressive plastic elongation of 0.2–2.9%, and Vickers hardness of 534–599. The finding of the new Cu–Zr–Ag ternary glassy alloy system with high GFA and good mechanical properties is important for development and scientific studies of bulk glassy alloys.

Photoelectrochemical properties of N-doped self-organized titania nanotube layers with different thicknesses

Abstract: The present work reports nitrogen doping of self-organized TiO2 nanotubular layers. Different thicknesses of the nanotubular layer architecture were formed by electrochemical anodization of Ti in different fluoride-containing electrolytes; tube lengths were 500 nm, 2.5 μm, and 6.1 μm. As-formed nanotube layers were annealed to an anatase structure and treated in ammonia environment at 550 °C to achieve nitrogen doping. The crystal structure, morphology, composition and photoresponse of the N-doped were characterized by scanning electron microscopy, x-ray diffraction, x-ray photoelectron spectroscopy, and photoelectrochemical measurements. Results clearly show that successful N-doping of the TiO2 nanotubular layers can be achieved upon ammonia treatment. The magnitude of the photoresponse in ultraviolet and visible light is strongly dependent on the thicknesses of the layers. This effect is ascribed to recombination effects along the tube length.

Dynamic nanomechanical response of nacre

Abstract: Nacre, the shiny inner layer of mollusk shells is a model biomimetic nanocomposite system. Its exceptional mechanical properties have been the inspiration for materials scientists for several decades. Nacre exhibits a layered brick and mortar structure. It is composed of 95% inorganic (aragonitic CaCO3) phase and 5% organic (mainly proteins and polysaccharides) phase that are arranged in interlocked brick and mortar architecture with the mineral as bricks and organics as the mortar. In the current work, we describe the dynamic nanomechanical behavior of nacre using dynamic nanoindentation (nano-DMA) experiments. Two sets of loads were applied to obtain the dynamic response from varying depths in nacre. These tests were performed at three different frequencies (25, 50, and 100 Hz) to study the effect of frequency on the dynamic properties of nacre. The loss modulus (E″) and the loss factor (tan δ) were measured. Both of these parameters were observed to increase with increase in depth. Significant increase in tan δ was observed with the increase in frequency. Photoacoustic Fourier transform infrared spectroscopic studies on nacre indicate the presence of water in nacre. This water may be present at nanograin interfaces in nacre platelets, at organic–inorganic interfaces, and also in the organic phase in nacre. We believe that water is one of the significant contributors to the viscoelasticity of nacre. Our results indicate that the aragonite platelets in nacre may also contribute to viscoelasticity.