Materials and Structures 

About: Materials and Structures is an academic journal published by Springer Science+Business Media. The journal publishes majorly in the area(s): Compressive strength & Cement. It has an ISSN identifier of 1359-5997. Over the lifetime, 4695 publications have been published receiving 154592 citations. The journal is also known as: Matériaux et constructions.

Compressive behaviour of concrete at high strain rates

Abstract: Experimental techniques commonly used for high strain-rate testing of concrete in compression, together with the methods used for measurement and recording of stress and strain, are critically assessed in the first part of this paper. The physical capability of each loading method is discussed and some consideration is given to the definitions used for specifying the loading rate. The second part reviews the dynamic compressive strength (mostly uniaxial rather than bi- or triaxial) of plain concrete, while in the third part a review on deformation behaviour indicates that uncertainty and disagreement exist concerning changes in axial strain at high strain rates.

Mix design and fresh properties for high-performance printing concrete

Abstract: This paper presents the experimental results concerning the mix design and fresh properties of a high-performance fibre-reinforced fine-aggregate concrete for printing concrete. This concrete has been designed to be extruded through a nozzle to build layer-by-layer structural components. The printing process is a novel digitally controlled additive manufacturing method which can build architectural and structural components without formwork, unlike conventional concrete construction methods. The most critical fresh properties are shown to be extrudability and buildability, which have mutual relationships with workability and open time. These properties are significantly influenced by the mix proportions and the presence of superplasticiser, retarder, accelerator and polypropylene fibres. An optimum mix is identified and validated by the full-scale manufacture of a bench component.

RILEM TC 162-TDF: Test and design methods for steel fibre reinforced concrete' - sigma-epsilon-design method - Final Recommendation

Abstract: General information Publication status: Published Organisations: Section for Structural Engineering, Department of Civil Engineering Contributors: Vandewalle, L., Nemegeer, D., Balazs, L., Barr, B., Barros, J., Bartos, P., Banthia, N., Criswell, M., Denarie, E., Di Prisco, M., Falkner, H., Gettu, R., Gopalaratnam, V., Groth, P., Hausler, V., Kooiman, A., Kovler, K., Massicotte, B., Mindess, S., Reinhardt, H., Rossi, P., Schaerlaekens, S., Schumacher, P., Schnutgen, B., Shah, S., Skarendahl, A., Stang, H., Stroeven, P., Swamy, R., Tatnall, P., Teutsch, M., Walraven, J. Pages: 560-567 Publication date: 2003 Peer-reviewed: Yes

Cover cracking as a function of bar corrosion: Part I-Experimental test

Abstract: The appraisal of concrete structures suffering rebar corrosion is one of the most urgent needs regarding the selection of the technical and economical optimum time for repair. Up to now this appraisal has been mainly based on empirical and subjective considerations. Among the different distressing consequences of rebar corrosion the best known is the cracking of concrete cover. However, very few data have been reported in the literature on the amount of corrosion needed to induce this cracking. In the present paper, some preliminary experiments are reported in which small reinforced beams are artificially corroded by an impressed current, and the amount of current (and loss of bar cross-section) needed to induce the crack at the surface are monitored, together with the evolution of crack width, by the use of strain gauges applied to the surface of the specimens. In a companion paper, a numerical model to relate the decrease in rebar cross-section to the cover cracking will be developed. That model is based on the orderly imposition of corrosion to finite elements of the rebar by a fictitious temperature increment that produces analogous effects, while concrete cracking is introduced by a standard smeared-crack model. The experimental results indicate that only a few micrometres of loss in rebar cross-section are needed to induce visible cover cracks (0.1 mm width) in the conditions of the test.