Showing papers in "Materials Research-ibero-american Journal of Materials in 2009"
TL;DR: In this article, a unified overview of matrix nanocomposites is presented underlining the need for these materials, their processing methods and some recent results on structure, properties and potential applications, perspectives including need for such materials in future space mission and other interesting applications together with market and safety aspects.
Abstract: Nanocomposites, a high performance material exhibit unusual property combinations and unique design possibilities. With an estimated annual growth rate of about 25% and fastest demand to be in engineering plastics and elastomers, their potential is so striking that they are useful in several areas ranging from packaging to biomedical applications. In this unified overview the three types of matrix nanocomposites are presented underlining the need for these materials, their processing methods and some recent results on structure, properties and potential applications, perspectives including need for such materials in future space mission and other interesting applications together with market and safety aspects. Possible uses of natural materials such as clay based minerals, chrysotile and lignocellulosic fibers are highlighted. Being environmentally friendly, applications of nanocomposites offer new technology and business opportunities for several sectors of the aerospace, automotive, electronics and biotechnology industries.
1,032 citations
TL;DR: In this article, the authors determined the kinetics of sigma phase formation in UNS S31803 Duplex Stainless Steel (DSS), describing the phase transformations that occur in isothermal aging between 700 and 900 oC for time periods up to 1032 hours.
Abstract: This work determines the kinetics of sigma phase formation in UNS S31803 Duplex Stainless Steel (DSS), describing the phase transformations that occur in isothermal aging between 700 and 900 oC for time periods up to 1032 hours, allowing the determination of the Time-Temperature-Precipitation (TTP) diagram for sigma phase and proposing a model to predict the kinetics of sigma phase formation using a Johnson-Mehl-Avrami (JMA) type expression. The higher kinetics of sigma phase formation occurs at 850 oC. However, isothermal aging between 700 and 900 oC for time periods up to 1032 hours are not sufficient to the establishment of thermodynamic equilibrium. Activation energy for both nucleation and growth of sigma phase is determined (185 kJ.mol-1) and its value is equivalent to the activation energy for Cr diffusion in ferrite, indicating that diffusion of Cr is probably the major thermally activated process involved in sigma phase formation. The determined JMA type expression presents good fit with experimental data between 700 and 850 oC.
139 citations
TL;DR: In this paper, the influence of calcium carbonate nanoparticles in both tensile and impact mechanical properties of polypropylene homopolymer was studied and it was concluded that the tensile properties depend on the surface contact area of nanoparticles and on their dispersion.
Abstract: The aim of this work was to study the influence of calcium carbonate nanoparticles in both tensile and impact mechanical properties of a polypropylene homopolymer. Four compositions of PP/CaCO3 nanocomposites were prepared in a co-rotational twin screw extruder machine with calcium carbonate content of 3, 5, 7 and 10 wt. (%) The tests included SEM analyzes together with EDS analyzer and FTIR spectroscopy for calcium carbonate, tensile and impact tests for PP and the nanocomposites. The results showed an increase in PP elastic modulus and a little increase in yield stress. Brittle-to-ductile transition temperature was reduced and the impact resistance increased with the addition of nanoparticles. From the stress-strain curves we determined the occurrence of debonding process before yielding leading to stress softening. Debonding stress was determined from stress-strain curves corresponding to stress in 1% strain. We concluded that the tensile properties depend on the surface contact area of nanoparticles and on their dispersion. Finally we believe that the toughening was due to the formation of diffuse shear because of debonding process.
115 citations
TL;DR: In this article, maleic anhydride-modified polypropylene (PP) and rice husk flour (RHF) composites were prepared by melt extrusion, and the presence of MAPP improved the tensile strength of the composites.
Abstract: Rice husk is a by-product of rice milling process that usually finds inadequate final disposal (burning, land filling). Thermoplastics composites filled with rice husk flour are materials that offer an alternative for using this agricultural resource viewing the production of low dense materials with some specific properties. In this work composites of polypropylene (PP) and rice husk flour (RHF) were prepared by melt extrusion. Maleic anhydride-modified PP (MAPP) was added as a coupling agent. It was verified that tensile strength decreased with filler loading. The presence of MAPP improved this property showing a strong dependence on the MAPP/RHF ratio (MAPP/RHF = 0.03 produced the best results). The density of the composites slightly increased with filler and coupling agent in comparison to pure PP. The presence of MAPP diminished more than 20% water uptake in highly-loaded composites.
107 citations
TL;DR: The results revealed that a difference of indentation time did not influence the microhardness number of enamel and dentin, and the tooth hardness number for different loads may not be acceptable for comparison.
Abstract: The aim of this study was to determine the effect of variations in indentation load and time on the Knoop and Vickers hardness numbers (KHN and VHN) for enamel and dentin. Twenty molar teeth were divided into twenty enamel and twenty dentin specimens. Each specimen was tested using a Knoop or Vickers microhardness tester at different loads and times. The difference in hardness between the groups was analyzed with two-way ANOVA followed by a Tukey test. The results revealed that a difference of indentation time did not influence the microhardness number of enamel and dentin. The KHN values of enamel and the VHN values of dentin were affected by variation of test loads. Therefore, the tooth hardness number for different loads may not be acceptable for comparison.
103 citations
TL;DR: The mechanical behavior of polymer concrete reinforced with textile trimming waste was investigated in this article, where fiber content and resin/sand weight ratio were considered relative to the behavior of polyurethane reinforced with yarn fibers.
Abstract: The mechanical behavior of polymer concrete reinforced with textile trimming waste was investigated. Two series of polymer concrete formulations were studied, with different resin/sand (i.e. binder/fine aggregate) weight ratios. In each series, recycled textile chopped fibers at 1 and 2% of the total weight was used. Flexural and compressive tests were performed at room temperature and load vs. displacement curves were plotted up to failure. In the study, both the influence of fiber content and resin/sand weight ratio were considered relative to the behavior of polymer concrete reinforced with textile fibers. A decrease in properties was observed as function of textile fibers content. When specific properties were considered, this tendency was kept. However, higher textile fibers content lead to a smoother failure, unlike brittleness failure behavior of unreinforced polymer concrete.
99 citations
TL;DR: The morphology of the membrane is the predominant factor for higher protein release, compared with pore size and number of pores, in natural rubber latex membranes used as a protein delivery system.
Abstract: In this work, we propose natural rubber latex (NRL) membranes as a protein delivery system. For this purpose Bovine Serum Albumin (BSA) was incorporated into the latex solution for in vitro protein delivery experiments. Different polymerization temperatures were used, from -10 to 27 °C, in order to control the membrane morphology. These membranes were characterized by Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), as well as the Lowry Method to measure the BSA release. SEM and AFM microscopy analysis showed that the number, size and distribution of pores in NRL membranes can be varied, as well as its overall morphology. We have found that the morphology of the membrane is the predominant factor for higher protein release, compared with pore size and number of pores. Results demonstrated that the best drug-delivery system was the membrane polymerized at RT (27 °C), which does release 66% of its BSA content for up to 18 days. Our results indicate that NRLb could be used in the future as an active membrane that could accelerate bone healing in GBR.
92 citations
TL;DR: In this paper, different mixtures of poly(hydroxybutyrate) or PHB and polypropylene or PP were extruded and injected, and their miscibility, mechanical properties and degradability in different soils were analyzed.
Abstract: The ever increasing accumulation of plastic waste in the environment has motivated research on polymers that degrade rapidly after being discarded as possible substitutes for conventional inert plastics. Biodegradable polymers can be an alternative, since they have non-toxic residual products and low environmental permanence. Poly (hydroxybutyrate) is a biodegradable polymer with a strong potential for industrial purposes, but its thermal instability and fragility limit its applications. Thus, an alternative to improve the processability and properties of poly (hydroxybutyrate) is to mix it with another polymer, not necessarily a biodegradable one. In this work, different mixtures of poly(hydroxybutyrate) or PHB and polypropylene or PP were extruded and injected. After processing, the blends were studied and their miscibility, mechanical properties and degradability in different soils were analyzed. The main results indicated that the PHB/PP blends had better mechanical properties than pure PHB, as well as improved immiscibility and higher degradation in alkaline soil. The poly-hydroxybutyrate/polypropylene blends showed a tendency for lower crystallinity and stiffness of the polymer matrix, proportional to the amount of polypropylene in the blends, rendering them less stiff and fragile. The degradation tests showed that both pure PHB and blends with 90% PHB and 10% PP were degraded, with loss of their mechanical properties and weight.
84 citations
TL;DR: In this paper, a study involving mechanical (flexural, shear, tensile and compressive tests) and morphological characterizations of four different laminates based on 2 epoxy resin systems (8552TM and F584TM) and 2 carbon fiber fabric reinforcements (Plain Weave (PW) and Eight Harness Satin (8HS)).
Abstract: Carbon fiber reinforced composites (CFRC) have been used in aeronautical industry in the manufacture of different aircraft components that must attend tight mechanical requirements. This paper shows a study involving mechanical (flexural, shear, tensile and compressive tests) and morphological characterizations of four different laminates based on 2 epoxy resin systems (8552TM and F584TM) and 2 carbon fiber fabric reinforcements (Plain Weave (PW) and Eight Harness Satin (8HS)). All laminates were obtained by handing lay-up of prepregs plies (0o/90o) and consolidation in an autoclave following an appropriate curing cycle with vacuum and pressure. The results show that the F584-epoxy matrix laminates present better mechanical properties in the tensile and compressive tests than 8552 composites. It is also observed that PW laminates for both matrices show better flexural and interlaminar shear properties.
83 citations
TL;DR: In this article, a method of hydrothermal synthesis using a single temperature (200oC) for preparing plate-like crystals of well-crystallised boehmite with ellipsoid, rhombic, hexagonal, and lath-like profiles by using different precursors is presented.
Abstract: Aluminium monohydroxide, also known as aluminium oxyhydroxide (boehmite - AlO[OH]), is water insoluble but crystallises into microcrystals of various shapes. When, by X-ray diffraction, the microcrystals present a basal reflexion (d[020]) of 0.611 nm, the crystalline structure is referred to as "well-crystallised" boehmite. Natural and synthetic crystals of well-crystallised boehmite can have a plate-like shape with either a rhombic or hexagonal profile. Synthetic crystals can also be lath-like or ellipsoid in shape. The purpose of this paper is to present a method of hydrothermal synthesis using a single temperature (200 oC) for preparing plate-like crystals of well-crystallised boehmite with ellipsoid, rhombic, hexagonal, and lath-like profiles by using different precursors. Our observations suggest that all of these shapes are stages of growth of the microcrystals of well-crystallised boehmite along the c-axis direction of the rhombic crystals.
76 citations
TL;DR: In this paper, a polyamide 66 (PA66) nanofibers of different molecular weights were obtained by electrospinning of formic acid solutions, and an ionic salt, NaCl, was also added to the solutions to increase the conductivity.
Abstract: Polyamide 66 (PA66) nanofibers of different molecular weights were obtained by electrospinning of formic acid solutions. An ionic salt, NaCl, was also added to the solutions to increase the conductivity. PA66 concentrations between 15-17 wt.(%)/v and electrical fields between 2.0 and 2.5 kV/cm were the best conditions to produce the smallest nanofibers; however, the addition of NaCl increased the fibers average diameters.The characterization of the fibers was done by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), wide angle X rays diffraction (WAXD) and Fourier Transformed Infrared (FTIR). As the molecular weight decreased, the nanofibers average diameters also decreased; however, critical number average and weight average molecular weights were necessary for electrospinning. As the amounts of carboxyl terminal groups (CTG) increased, the nanofibers average diameters decreased; however, above CTG's critical values of 8.7 x 10-5 mol.g-1 no electrospinning was possible. The addition of ionic salt increased the electrical conductivity of the solutions and increased the nanofibers' average diameters. By DSC, residual solvent in all the electrospun mats was found; two melting endotherms, one between 248 and 258 °C and the other one between 258 and 267 °C, depending on the sample were also observed. These endotherms were attributed to the melting, re-crystallization and re-melting of the PA66 α-phase. The nanofibers had low % of crystallinity compared to a textile fiber. By WAXS and FTIR, confirmation of the presence of α-phase crystals, of small dimensions and highly imperfect and of a very small amount of β and γ-phases crystals in the nanofibers structure was obtained.
TL;DR: In this article, the performance of a polymeric system was evaluated considering the effect of hygrothermal aging, and the appearance of surface voids was also observed for the processed material after aging in water at 60 oC for a maximum period of 64 days.
Abstract: Derakene is a vinyl ester resin largely employed as matrix for polymeric based composite systems. In this work, the performance of such polymeric system was evaluated considering the effect of hygrothermal aging. The mechanical and thermal properties were examined for the processed material before and after ageing in water at 60 oC for a maximum period of 64 days. Both analyses indicated the occurrence of post cure of the system after 16 days due to exposition at 60 oC in water, which was also confirmed by analyses in samples with post cure treatment. Moreover, it was observed plasticizing of resin after 36 and 64 days of ageing. Micro structural and fracture surface analyses were carried out in order to characterize the samples. The appearance of surface voids was also observed.
TL;DR: In this article, molecular imprinted polymers (MIP's) for quercetin were successfully synthesized by a thermal polymerization method using quercETin as template molecule, acrylamide as functional monomer and ethylene glycol dimethacrylate as cross-linker in the presence of four different porogenic solvents: 1,4-dioxane, tetrahydrofuran (THF), acetone, and acetonitrile.
Abstract: Molecularly imprinted polymers (MIP's) for quercetin were successfully synthesized by a thermal polymerization method using quercetin as template molecule, acrylamide as functional monomer and ethylene glycol dimethacrylate as cross-linker in the presence of four different porogenic solvents: 1,4-dioxane, tetrahydrofuran (THF), acetone, and acetonitrile. The selective performance of obtained MIP's was evaluated through HPLC analysis. The results indicated that the MIP obtained in THF showed the highest capacity and selectivity. The Scatchard method also supported HPLC results. The results were interpreted by computational quantum chemical analysis through Onsager self-consistent reaction field (SCRF) technique in term of stabilization energy. It was also found that the amount of porogenic solvent used had impact on the adsorption effectiveness of MIP's.
TL;DR: In this article, the effects of the carburizing temperature and time on the mechanical properties of mild steel carburized with activated carbon, at 850, 900 and 950 oC, soaked at carburising temperature for 15 and 30 minutes, quenched in oil, tempered at 550 oC and held for 60 minutes.
Abstract: Due to the complexity of controlling parameters in carburization, there has been relatively little work on process variables during the surface hardening process. This work focuses on the effects of the carburizing temperature and time on the mechanical properties of mild steel carburized with activated carbon, at 850, 900 and 950 oC, soaked at the carburizing temperature for 15 and 30 minutes, quenched in oil, tempered at 550 oC and held for 60 minutes. Prior carburization process, standard test samples were prepared from the as received specimen for tensile and impact tests. After carburization process, the test samples were subjected to the standard test and from the data obtained, ultimate tensile strength, engineering strain, impact strength, Youngs' moduli were calculated. The case and core hardness of the carburized tempered samples were measured. It was observed that the mechanical properties of mild steels were found to be strongly influenced by the process of carburization, carburizing temperature and soaking time at carburizing temperature. It was concluded that the optimum combination of mechanical properties is achieved at the carburizing temperature of 900 oC followed by oil quenching and tempering at 550 oC.
TL;DR: In this article, the development of α and β-phases and the molecular orientation of injection molded disks of two isotactic polypropylene (i-PP) resins were studied by wide angle X-ray diffraction (WAXD) and pole figures.
Abstract: The development of α and β-phases and the molecular orientation of injection molded disks of two isotactic polypropylene (i-PP) resins were studied by wide angle X-ray diffraction (WAXD) and pole figures. A nucleated (NPP) and non-nucleated (HPP) polymers were analyzed. The main proposal of this article was the comprehensive study of the interrelations between the processing conditions, phase contents and PP α-phase molecular orientation of injection molded PP resins. In both resins, it was observed that the α-phase was present in all regions along the thickness while the β-phase was present mainly in the external layers, decreasing from the surface to the core; however this last phase was present in a very small amount in the NPP resin. For both polymers, the orientation of the macromolecules c-axis was higher along the flow direction (RD) than along the transverse direction (TD). The b-axis of the PP α-phase molecules was oriented to the thickness direction (ND). The orientation of the c-axis along RD and b-axis along ND of the NPP samples was considerably higher than of the HPP samples, due to the NPP faster crystallization kinetics. For both polymers, the most influential processing parameters on the molecular orientation were the mold temperature and flow rate. The results indicate that, as the mold temperature increased, the characteristic molecular orientation of PP α-phase, with c-axis along RD and b-axis along ND, decreased. With increase in the flow rate an increase of the c-axis molecular orientation of the samples along RD was observed.
TL;DR: In this article, mechanical and tribological properties of stainless steels submited to glow discharge ion nitriding are reported, where the atmosphere was 20:80 - N2:H2 with substrate temperatures ranging from 300 to 500 °C.
Abstract: Mechanical and tribological properties os AISI 304 and AISI 316 stainless steels submited to glow discharge ion nitriding are reported.The atmosphere was 20:80 - N2:H2 with substrate temperatures ranging from 300 to 500 °C. Treatment at 300 °C produced expanded austenite (γN) in both steels. Increasing the temperature, the phases γ´-Fe4N and - Fe2+xN were present and the latter is the major phase for AISI 304. At 500 °C, the CrN phase was also identified in both steels. Hardnesses of about 13-14 GPa at near surface regions were obtained in both steels. Moreover, AISI 316 nitrided at 500 °C has the deepest hard layer. Tribological tests showed that wear can be reduced by up to a factor of six after the nitriding processes, even for a working temperature of 300 °C. The profiles during and after nanoscratch tests did not reveal significant differences after nitriding processes in both steels.
TL;DR: In this paper, the effects of polyurethane adhesive strength (i.e. lap shear strength) on woodto-wood and metal-to-metal bonding through various types of polyols, cross-linking density, isocyanate adducts and also to compare adhesive strength between wood to wood and metal to metal surface.
Abstract: Polyurethane adhesives made from synthetic chemicals are non-biodegradable, costly and difficult to find raw materials from local market. To avoid solid pollution problem, cost effectiveness and easy availability of raw materials, biomaterials based polyurethane adhesives are used in current industrial interest. Direct use of castor oil in polyurethane adhesive gives limited hardness. Modification on active sites of castor oil to utilize double bond of unsaturated fatty acid and carboxyl group yields new modified or activated polyols, which can be utilized for polyurethane adhesive formulation. In view of this, we have synthesized polyurethane adhesives from polyester polyols, castor oil based polyols and epoxy based polyols with Isocyanate adducts based on castor oil and trimethylolpropane. To study the effects of polyurethane adhesive strength (i.e. lap shear strength) on wood-to-wood and metal-to-metal bonding through various types of polyols, cross-linking density, isocyanate adducts and also to compare adhesive strength between wood to wood and metal to metal surface. These polyols and polyurethanes were characterized through GPC, NMR and IR-spectroscopy, gel and surface drying time. Thermal stability of PU adhesives was determined under the effect of cross-linking density (NCO/OH ratio). The NCO/OH ratio (1.5) was optimized for adhesives as the higher NCO/OH ratio (2.0) increasing cross-linking density and decreases adhesion. Lower NCO/OH ratio (1.0) provideslow cross-linking density and low strength of adhesives.
TL;DR: In this paper, the surface of glassy carbon (GC) electrode has been modified by oxidation of L-cysteine, and the modified electrode was used to obtain the calibration curve and it exhibited a stable and sensitive response to DA.
Abstract: The surface of glassy carbon (GC) electrode has been modified by oxidation of L-cysteine. The covalent modified GC electrode with L-Cysteine has been studied, according the supporting electrolyte used. Favourable interactions between the L-cysteine film and DA enhance the current response compared to that at the Nafion GC and bare GC electrodes, achieving better performances than those other electrodes. This behaviour was as result of the adsorption of the cysteine layer film, compact and uniform formation; depending on L-cysteine solution (phosphate buffer or chloridric acid supporting electrolyte) used for modifying GC surface. In cyclic voltammetric measurements, modified electrodes can successfully separate the oxidation/reduction DA peaks in different buffer solutions, but an evident dependence in the response was obtained as function of pH and modified electrode. The modified electrode prepared with L-cysteine/HCl solution was used to obtain the calibration curve and it exhibited a stable and sensitive response to DA. The results are described and discussed in the light of the existing literature.
TL;DR: In this paper, the influence of calcium carbonate nanoparticles in polypropylene crystallization process was studied, which showed an increase in PP crystallization temperature and crystallinity degree, and a reduction in spherullites size.
Abstract: The aim of this work was to study the influence of calcium carbonate nanoparticles in crystallization process of polypropylene. Four compositions of PP/CaCO3 nanocomposites were prepared in a co-rotational twin screw extruder machine with calcium carbonate content of 3, 5, 7 and 10 wt. (%). The tests included SEM analyzes for calcium carbonate, differential scanning calorimetry (DSC) and wide angle X-ray diffraction (WAXD) for the nanocomposites. The results showed an increase in PP crystallization temperature and crystallinity degree, and a reduction in spherullites size. The formation of PP β phase was confirmed by DSC and WAXD results. Finally from DSC analyses under isothermal conditions it was confirmed that calcium carbonate nanoparticles have a nucleation effect in polypropylene crystallization process by reducing the half crystallization time and increasing the kinetic constant (k).
TL;DR: In this paper, the effect of freezing methods on the properties of lyophilized porous silk fibroin membranes was evaluated using XRD, FTIR, TGA, DSC and SEM.
Abstract: Silk fibroin is a fibrous protein that has been extensively studied for application in the biomedical field, and has been used as a scaffold for bone tissue engineering. Biomaterials made of proteins are prone to physical and chemical degradation during storage; lyophilization, a drying method that consists of freezing and drying steps, is known to promote minimal changes in structure and biological activity of biomaterials. This study evaluates the effect of freezing methods on the properties of lyophilized porous silk fibroin membranes. The membranes were obtained from silk fibroin solution, frozen in liquid nitrogen or ultrafreezer, lyophilized, and then characterized by XRD, FTIR, TGA, DSC and SEM. Although the membranes presented similar physical, chemical and microstructural characteristics, quench freezing with liquid nitrogen, followed by lyophilization, promoted collapse of the membranes, while slow cooling performed by ultrafreezer preserved membrane integrity.
TL;DR: In this paper, annealed electrolytic copper wire (ETP) with 0.5 mm original diameter was reduced by 19% in dies with 2β = 10o and 18o and Hc = 35 and 50%.
Abstract: The study of die geometry is vital in determining the surface and mechanical properties of drawn wires, and consequently, their application. In this work, annealed electrolytic copper wire (ETP), with 0.5 mm original diameter was reduced by 19% in dies with 2β = 10o and 18o and Hc = 35 and 50%. The best experimental results were then studied by the Finite Element Method to simulate residual stress distribution. The experimental results show that the friction coefficient decreases as the wire drawing speed increases, and that low 2β and Hc values bring about the most favorable wiredrawing conditions. The simulation shows a variation in the axial and radial tensions, both for the compression and traction stresses on all regions during the wire drawing process. In conclusion, the influence of the internal die geometry on the drawn wire is clarified.
TL;DR: In this article, an attempt has been made to correlate slump, slump flow, slump time, percent flow and Vebe time to rheological parameters of high-performance concrete, and thirty numbers of concrete mixes without steel fibers and with steel fibers of specific dose have been considered during experiment.
Abstract: Conventional single-point workability tests continue to be used for specification and quality control of concrete despite their inherent limitations. These tests cannot characterize workability of concrete in terms of fundamental rheological parameters. Attempt has therefore been made to correlate slump, slump flow, slump flow time, percent flow and Vebe time to rheological parameters of high-performance concrete. Thirty numbers of concrete mixes without steel fibers and with steel fibers of specific dose have been considered during experiment. It has been observed that rheological parameters can be correlated to slump and slump flow. In case of fiber reinforced concrete, there is a decrease in percent flow with the increase in rheological parameters. Vebe time, however, remains unchanged up to yield stress 500 Pa and plastic viscosity 40 Pa.s beyond which it steeply increases with further increase in yield stress and plastic viscosity. Flow test may be a better test for FRC as it is sensitive over all ranges of workability of concrete.
TL;DR: In this article, the orientation distribution functions (ODFs) from measured pole figure data were calculated and the calculated textures based in a process of variant selection consistent with Patel and Cohen's theory, which emphasizes a mechanical component of free energy, were in good agreement with measured texture.
Abstract: Experiments have been conducted to study the strain induced transformation from austenite to martensite in a metastable AISI 301LN austenitic stainless steel, deformed by uniaxial tension applied along rolling direction. Samples deformed 10 and 20% have shown the presence of α´ martensite phase. Measured pole figures of martensite phase were compared to calculated ones, assuming no variant selection and selection of variants where interaction between stress and the plate of martensite adds to the driving force transformation variants. EBSD (electron back scatter diffraction) microtexture experiments and macrotexture X-ray diffraction were performed. The orientation distribution functions (ODFs) from measured pole figure data were calculated. The measured results were compared with calculated results in both polycrystalline and single crystal samples of austenite. The results showed that the calculated textures based in a process of variant selection consistent with Patel and Cohen's theory, which emphasizes a mechanical component of free energy, were in good agreement with measured texture.
TL;DR: In this paper, a sintering investigation for a specific LZSA glass-ceramic system composition was carried out, where a 18.8Li2O-8.3ZrO2-64.7Al 2O3 glass was prepared by melting the solids, quenching the melt in water, and grinding the resulting solid in order to obtain a powder (3.68 μm average particle diameter).
Abstract: The LZSA glass-ceramic system (Li2O-ZrO2-SiO2-Al2O 3) shows interesting properties, such as good chemical resistance, low thermal expansion, high abrasion resistance, and a low dielectric constant. However, in order to obtain a high performance material for specific applications, the sintering behavior must be better understood so that the porosity may be reduced and other properties improved. In this context, a sintering investigation for a specific LZSA glass-ceramic system composition was carried out. A 18.8Li2O-8.3ZrO2-64.2SiO2-8.7Al 2O3 glass was prepared by melting the solids, quenching the melt in water, and grinding the resulting solid in order to obtain a powder (3.68 μm average particle diameter). Subsequently, the glass powder was characterized (chemical analysis and determination of thermal properties) and the sintering behavior was investigated using optical non-contact dilatometry measurements. The results showed that the crystallization process strongly reduced the sintering in the temperature interval from 785 to 940 °C, and a maximum thermal shrinkage of 15.4% was obtained with operating conditions of 1020 °C and 180 minutes.
Abstract: Bioactive glass/polymer hybrids are promising materials for biomedical applications because they combine the bioactivity of these glasses with the flexibility of polymers. In this work it was evaluated the effect of increasing the PVA content of the on structural characteristics and mechanical properties of hybrid. The hybrids were prepared with 70 wt. (%) SiO2-30 wt. (%) CaO and PVA fractions of 20 to 60 wt. (%) by the sol-gel method. The structural and mechanical characterization was done by FTIR, SEM and compression tests. To reduce the acidic character of the hybrids due to the catalysts added, different neutralization solutions were tested. The calcium acetate alcoholic solution was the best neutralizing method, resulting in foams with final pH of about 7.0 and small sample contraction. The foams presented porosity of 60-85 wt. (%) and pore diameters of 100-500 μm with interconnected structure. An increase of PVA fraction in the hybrids improved their mechanical properties. The scaffolds produced provided a good environment for the adhesion and proliferation of osteoblasts.
TL;DR: In this paper, the authors investigated the recycling of kaolin processing waste in the manufacture of mullite-based ceramics based on the statistical design of mixture experiments methodology, which can be successfully used to optimize formulations containing large amount of wastes.
Abstract: Mineral extraction and processing industries have been cited as sources of environmental contamination and pollution. However, waste recycling represents an alternative recovery option, which is interesting from an environmental and economic standpoint. In this work, recycling of kaolin processing waste in the manufacture of mullite-based ceramics was investigated based on the statistical design of mixture experiments methodology. Ten formulations using kaolin processing waste, alumina and ball clay were used in the experiment design. Test specimens were fired and characterized to determine their water absorption and modulus of rupture. Regression models were calculated, relating the properties with the composition. The significance and validity of the models were confirmed through statistical analysis and verification experiments. The regression models were used to analyze the influence of waste content on the properties of the fired bodies. The results indicated that the statistical design of mixture experiments methodology can be successfully used to optimize formulations containing large amount of wastes.
TL;DR: In this paper, the authors describe non-conventional sisal (Agave sisalana) chemical (organosolv) pulp from residues of cordage as reinforcement to cement based materials.
Abstract: The present work describes non-conventional sisal (Agave sisalana) chemical (organosolv) pulp from residues of cordage as reinforcement to cement based materials. Sisal organosolv pulp was produced in a 1:1 ethanol/water mixture and post chemically and physically characterized in order to compare its properties with sisal kraft pulp. Cement based composites reinforced with organosolv or kraft pulps and combined with polypropylene (PP) fibres were produced by the slurry de-watering and pressing method as a crude simulation of the Hatschek process. Composites were evaluated at 28 days of age, after exposition to accelerated carbonation and after 100 soak/dry cycles. Composites containing organosolv pulp presented lower mechanical strength, water absorption and apparent porosity than composites reinforced with kraft pulp. The best mechanical performance after ageing was also achieved by samples reinforced with kraft pulp. The addition of PP fibres favoured the maintenance of toughness after ageing. Accelerated carbonation promoted the densification of the composites reinforced with sisal organosolv + PP fibres.
TL;DR: The increase in elastomer concentration added to polymethyl methacrylate raised the impact resistance and decreased the fracture resistance, and Fracture resistance was superior for high-resistance acrylic resin.
Abstract: The purpose of this study was to evaluate the impact and fracture resistance of acrylic resins: a heat-polymerized resin, a high-impact resin and an experimental polymethyl methacrylate with elastomer in different proportions (10, 20, 40 and 60%). 120 specimens were fabricated and submitted to conventional heat-polymerization. For impact test, a Charpy-type impact tester was used. Fracture resistance was assessed with a 3-point bending test by using a mechanical testing machine. Ten specimens were used for each test. Fracture (MPa) and impact resistance values (J.m-1) were submitted to ANOVA - Bonferroni's test - 5% significance level. Materials with higher amount of elastomer had statistically significant differences regarding to impact resistance (p < 0.05). Fracture resistance was superior (p < 0.01) for high-resistance acrylic resin. The increase in elastomer concentration added to polymethyl methacrylate raised the impact resistance and decreased the fracture resistance. Processing the material by injection decreased its resistance to impact and fracture.
TL;DR: In this article, a weight-based analysis was made of the translaminar Charpy impact toughness performance of conventional and advanced composite materials for aircraft fabrication, including carbon-epoxy (C-Ep) and hybrid fiber-metal (Titanium-Graphite) laminates.
Abstract: A weight-based analysis was made of the translaminar Charpy impact toughness performance of conventional and advanced composite materials for aircraft fabrication. The materials were carbon-epoxy (C-Ep) and hybrid fiber-metal TiGr (Titanium-Graphite) laminates. 5 mm-thick three-point bend specimens were tested over a temperature range of -70 to 180 oC to reproduce typical in-service conditions of supersonic jetliners. The energies required for the processes of damage initiation (Ei), damage propagation (Ep), and whole fracture (Et = Ei + Ep), were evaluated at two loading rates, namely, 2.25 and 5.52 m/s in an instrumented Charpy impact testing machine. C-Ep laminates with unidirectional fiber tapes arranged in cross-ply architecture consistently showed the best performance in terms of damage initiation toughness, whereas the hybrid fiber-metal laminate TiGr excelled in terms of propagation toughness. On the other hand, the overall performance of bi-directional fabric C-Ep laminates was very disappointing. The impact behavior of composite laminates was substantiated by a qualitative analysis of topographic aspects of fracture surfaces.
TL;DR: In this article, the influence of applied current density on the morphology of polypyrrole films was studied by Scanning Electron Microscopy and the films displayed a cauliflower-like structure consisting of micro-spherical grains.
Abstract: Electrodeposition of polypyrrole films on aluminum from aqueous solutions containing p-toluene sulfonic acid and pyrrole was performed by cyclic voltammetry and galvanostatic technique. The influence of applied current density on the morphology of the films was studied by Scanning Electron Microscopy. The films displayed a cauliflower-like structure consisting of micro-spherical grains. This structure is related to dopand intercalation in the polymeric chain. Films deposited at higher current density were more susceptible to the formation of pores and defects along the polymeric chain than films deposited at lower current density. These pores allow the penetration of aggressive species, thereby favoring the corrosion process.