Showing papers in "Nuclear Fusion in 2015"

Integrated modeling applications for tokamak experiments with OMFIT

Abstract: One modeling framework for integrated tasks (OMFIT) is a comprehensive integrated modeling framework which has been developed to enable physics codes to interact in complicated workflows, and support scientists at all stages of the modeling cycle. The OMFIT development follows a unique bottom-up approach, where the framework design and capabilities organically evolve to support progressive integration of the components that are required to accomplish physics goals of increasing complexity. OMFIT provides a workflow for easily generating full kinetic equilibrium reconstructions that are constrained by magnetic and motional Stark effect measurements, and kinetic profile information that includes fast-ion pressure modeled by a transport code. It was found that magnetic measurements can be used to quantify the amount of anomalous fast-ion diffusion that is present in DIII-D discharges, and provide an estimate that is consistent with what would be needed for transport simulations to match the measured neutron rates. OMFIT was used to streamline edge-stability analyses, and evaluate the effect of resonant magnetic perturbation (RMP) on the pedestal stability, which have been found to be consistent with the experimental observations. The development of a five-dimensional numerical fluid model for estimating the effects of the interaction between magnetohydrodynamic (MHD) and microturbulence, and its systematic verification against analytic models was also supported by the framework. OMFIT was used for optimizing an innovative high-harmonic fast wave system proposed for DIII-D. For a parallel refractive index , the conditions for strong electron-Landau damping were found to be independent of launched and poloidal angle. OMFIT has been the platform of choice for developing a neural-network based approach to efficiently perform a non-linear multivariate regression of local transport fluxes as a function of local dimensionless parameters. Transport predictions for thousands of DIII-D discharges showed excellent agreement with the power balance calculations across the whole plasma radius and over a broad range of operating regimes. Concerning predictive transport simulations, the framework made possible the design and automation of a workflow that enables self-consistent predictions of kinetic profiles and the plasma equilibrium. It is found that the feedback between the transport fluxes and plasma equilibrium can significantly affect the kinetic profiles predictions. Such a rich set of results provide tangible evidence of how bottom-up approaches can potentially provide a fast track to integrated modeling solutions that are functional, cost-effective, and in sync with the research effort of the community.

Partial detachment of high power discharges in ASDEX Upgrade

Abstract: Detachment of high power discharges is obtained in ASDEX Upgrade by simultaneous feedback control of core radiation and divertor radiation or thermoelectric currents by the injection of radiating impurities. So far 2/3 of the ITER normalized heat flux Psep/R = 15 MW m−1 has been obtained in ASDEX Upgrade under partially detached conditions with a peak target heat flux well below 10 MW m−2. When the detachment is further pronounced towards lower peak heat flux at the target, substantial changes in edge localized mode (ELM) behaviour, density and radiation distribution occur. The time-averaged peak heat flux at both divertor targets can be reduced below 2 MW m−2, which offers an attractive DEMO divertor scenario with potential for simpler and cheaper technical solutions. Generally, pronounced detachment leads to a pedestal and core density rise by about 20–40%, moderate (<20%) confinement degradation and a reduction of ELM size. For AUG conditions, some operational challenges occur, like the density cut-off limit for X-2 electron cyclotron resonance heating, which is used for central tungsten control.

Advances in the Physics Basis for the European DEMO Design

Abstract: In the European fusion roadmap, ITER is followed by a demonstration fusion power reactor (DEMO), for which a conceptual design is under development. This paper reports the first results of a coherent effort to develop the relevant physics knowledge for that (DEMO Physics Basis), carried out by European experts. The program currently includes investigations in the areas of scenario modeling, transport, MHD, heating & current drive, fast particles, plasma wall interaction and disruptions.

Divertor studies in nitrogen induced completely detached H-modes in full tungsten ASDEX Upgrade

Abstract: The first stable completely detached H-mode plasma in the full tungsten ASDEX Upgrade has been achieved Complete detachment of both targets is induced by nitrogen seeding into the divertor Two new phases are added to the detachment classification described in Potzel et al (2014 Nucl Fusion 54 013001): first, the line integrated density increases by about 15% with partial detachment of the outer divertor Second, complete detachment of both targets is correlated to the appearance of intense, strongly localized, stable radiation at the X-point Radiated power fractions, frad, increase from about 50% to 85% with nitrogen seeding X-point radiation is accompanied by a loss of pedestal top plasma pressure of about 60% However, the core pressure at ?pol?

Tungsten ‘fuzz’ growth re-examined: the dependence on ion fluence in non-erosive and erosive helium plasma

Abstract: The thickness x, of tungsten fuzz layers are measured for non-varying helium (He) plasma exposure conditions spanning four orders of ion fluence (1024–1028m−2) and flux (1019–1023 m−2 s−1), at 1000–1140 K under low energy He ion impact (50–80) eV. The data obtained are complemented by previously published data of similar growth conditions, and collectively analysed. The new analysis allows for the reconciliation of fast high flux growth with commonly observed slower growth at lower flux. It is demonstrated that the standing t1/2 time dependence is a special case of a more general expression for determining the layer thickness, , that depends on , an incubation fluence , and the growth constant m4, which is temperature dependent. The incubation fluence, which must be exceeded before the observation on the onset of fuzz surface morphology is determined to be m−2. In fuzz growth-erosion regimes, characterized by an erosion constant , that is proportional to the sputter yield, an analytic solution for has been found, by solving the growth-erosion equilibria problem of prior work with the Lambert W function. Simple limit expressions follow from the solution for determining the equilibrium fluence and fuzz thickness; the predictions of such being in good agreement with previous fuzz growth-erosion equilibria results in the literature.

Enhanced H-mode pedestals with lithium injection in DIII-D

Abstract: Periods of edge localized mode (ELM)-free H-mode with increased pedestal pressure and width were observed in the DIII-D tokamak when density fluctuations localized to the region near the separatrix were present. Injection of a powder of 45 µm diameter lithium particles increased the duration of the enhanced pedestal phases to up to 350 ms, and also increased the likelihood of a transition to the enhanced phase. Lithium injection at a level sufficient for triggering the extended enhanced phases resulted in significant lithium in the plasma core, but carbon and other higher Z impurities as well as radiated power levels were reduced. Recycling of the working deuterium gas appeared unaffected by this level of lithium injection. The ion scale, kθρs ~ 0.1–0.2, density fluctuations propagated in the electron drift direction with f ~ 80 kHz and occurred in bursts every ~1 ms. The fluctuation bursts correlated with plasma loss resulting in a flattening of the pressure profile in a region near the separatrix. This localized flattening allowed higher overall pedestal pressure at the peeling–ballooning stability limit and higher pressure than expected under the EPED model due to reduction of the pressure gradient below the 'ballooning critical profile'. Reduction of the ion pressure by lithium dilution may contribute to the long ELM-free periods.

Advances in H-mode physics for long-pulse operation on EAST

Abstract: Since the 2012 International Atomic Energy Agency Fusion Energy Conference (IAEA-FEC), significant advances in both physics and technology has been made on the Experimental Advanced Superconducting Tomakak (EAST) toward a long-pulse stable high-confinement (H-mode) plasma regime. The experimental capabilities of EAST have been technically upgraded with the power enhancement (source power up to 26 MW) of the continuous-wave heating and current drive system, replacement of the upper graphite divertor with an ITER-like W monoblock divertor, and installation of a new internal cryopump in the upper divertor and a set of 16 in-vessel resonant magnetic perturbation (RMP) coils. This new upgrade enables EAST to be a unique operating device capable of investigating ITER-relevant long-pulse high-performance operations with dominant electron heating and low torque input within the next 5 years. Remarkable physics progress in controlling transient and steady-state divertor heat fluxes has been achieved on EAST, e.g. (i) edge-localized mode (ELM) mitigation/suppression with a number of attractive methods including lower hybrid wave (LHW), supersonic molecular beam injection (SMBI), RMPs, and real-time Li aerosol injection; and (ii) active control of steady-state power distribution by the synergy of LHW and SMBI. In the 2014 experimental campaign, a long-pulse high-performance H-mode plasma with H98 ~ 1.2 has been obtained with a duration over 28 s (~200 times the energy confinement time). In addition, several new experimental advances have been achieved in the last EAST campaign, including: (i) high-performance H-mode with βN ~ 2 and stored plasma energy ~220 kJ; (ii) H-mode plasma sustained by neutral beam injection (NBI) alone or modulated NBI with lower hybrid current drive (LHCD), for the first time in EAST; (iii) high current drive efficiency and nearly full noninductive plasmas maintained by the new 4.6 GHz LHCD system; (iv) demonstration of a quasi-snowflake divertor configuration; and (v) observation of a new edge-coherent mode and its effects on edge transport in H-mode plasmas.

Progress in the realization of the PRIMA neutral beam test facility

Abstract: The ITER project requires additional heating by two neutral beam injectors, each accelerating to 1 MV a 40 A beam of negative deuterium ions, to deliver to the plasma a power of about 17 MW for one hour. As these requirements have never been experimentally met, it was recognized as necessary to setup a test facility, PRIMA (Padova Research on ITER Megavolt Accelerator), in Italy, including a full-size negative ion source, SPIDER, and a prototype of the whole ITER injector, MITICA, aiming to develop the heating injectors to be installed in ITER. This realization is made with the main contribution of the European Union, through the Joint Undertaking for ITER (F4E), the ITER Organization and Consorzio RFX which hosts the Test Facility. The Japanese and the Indian ITER Domestic Agencies (JADA and INDA) participate in the PRIMA enterprise; European laboratories, such as IPP-Garching, KIT-Karlsruhe, CCFE-Culham, CEA-Cadarache and others are also cooperating. Presently, the assembly of SPIDER is on-going and the MITICA design is being completed. The paper gives a general overview of the test facility and of the status of development of the MITICA and SPIDER main components at this important stage of the overall development; then it focuses on the latest and most critical issues, regarding both physics and technology, describing the identified solutions.

Improved profile fitting and quantification of uncertainty in experimental measurements of impurity transport coefficients using Gaussian process regression

Abstract: The need to fit smooth temperature and density profiles to discrete observations is ubiquitous in plasma physics, but the prevailing techniques for this have many shortcomings that cast doubt on the statistical validity of the results. This issue is amplified in the context of validation of gyrokinetic transport models (Holland et al 2009 Phys. Plasmas 16 052301), where the strong sensitivity of the code outputs to input gradients means that inadequacies in the profile fitting technique can easily lead to an incorrect assessment of the degree of agreement with experimental measurements. In order to rectify the shortcomings of standard approaches to profile fitting, we have applied Gaussian process regression (GPR), a powerful non-parametric regression technique, to analyse an Alcator C-Mod L-mode discharge used for past gyrokinetic validation work (Howard et al 2012 Nucl. Fusion 52 063002). We show that the GPR techniques can reproduce the previous results while delivering more statistically rigorous fits and uncertainty estimates for both the value and the gradient of plasma profiles with an improved level of automation. We also discuss how the use of GPR can allow for dramatic increases in the rate of convergence of uncertainty propagation for any code that takes experimental profiles as inputs. The new GPR techniques for profile fitting and uncertainty propagation are quite useful and general, and we describe the steps to implementation in detail in this paper. These techniques have the potential to substantially improve the quality of uncertainty estimates on profile fits and the rate of convergence of uncertainty propagation, making them of great interest for wider use in fusion experiments and modelling efforts.

Design and first applications of the ITER integrated modelling & analysis suite

Abstract: The ITER Integrated Modelling & Analysis Suite (IMAS) will support both plasma operation and research activities on the ITER tokamak experiment. The IMAS will be accessible to all ITER members as a key tool for the scientific exploitation of ITER. The backbone of the IMAS infrastructure is a standardized, machine-generic data model that represents simulated and experimental data with identical structures. The other outcomes of the IMAS design and prototyping phase are a set of tools to access data and design integrated modelling workflows, as well as first plasma simulators workflows and components implemented with various degrees of modularity.

Design concept of K-DEMO for near-term implementation

Abstract: A Korean fusion energy development promotion law (FEDPL) was enacted in 2007. As a following step, a conceptual design study for a steady-state Korean fusion demonstration reactor (K-DEMO) was initiated in 2012. After the thorough 0D system analysis, the parameters of the main machine characterized by the major and minor radii of 6.8 and 2.1 m, respectively, were chosen for further study. The analyses of heating and current drives were performed for the development of the plasma operation scenarios. Preliminary results on lower hybrid and neutral beam current drive are included herein. A high performance Nb3Sn-based superconducting conductor is adopted, providing a peak magnetic field approaching 16 T with the magnetic field at the plasma centre above 7 T. Pressurized water is the prominent choice for the main coolant of K-DEMO when the balance of plant development details is considered. The blanket system adopts a ceramic pebble type breeder. Considering plasma performance, a double-null divertor is the reference configuration choice of K-DEMO. For a high availability operation, K-DEMO incorporates a design with vertical maintenance. A design concept for K-DEMO is presented together with the preliminary design parameters.

Effect of resonant magnetic perturbations on low collisionality discharges in MAST and a comparison with ASDEX Upgrade

Abstract: Sustained edge localized mode (ELM) mitigation has been achieved on MAST and AUG using resonant magnetic perturbations (RMPs) with various toroidal mode numbers over a wide range of low to medium collisionality discharges. The ELM energy loss and peak heat loads at the divertor targets have been reduced. The ELM mitigation phase is typically associated with a drop in plasma density and overall stored energy. In one particular scenario on MAST, by carefully adjusting the fuelling it has been possible to counteract the drop in density and to produce plasmas with mitigated ELMs, reduced peak divertor heat flux and with minimal degradation in pedestal height and confined energy. While the applied resonant magnetic perturbation field can be a good indicator for the onset of ELM mitigation on MAST and AUG there are some cases where this is not the case and which clearly emphasize the need to take into account the plasma response to the applied perturbations. The plasma response calculations show that the increase in ELM frequency is correlated with the size of the edge peeling-tearing like response of the plasma and the distortions of the plasma boundary in the X-point region. In many cases the RMPs act to increase the frequency of type I ELMs, however, there are examples where the type I ELMs are suppressed and there is a transition to a small or type IV ELM-ing regime.

Numerical modelling for divertor design of the WEST device with a focus on plasma–wall interactions

Abstract: In the perspective of operating tungsten monoblocks in WEST, the ongoing major upgrade of the Tore Supra tokamak, a dedicated modelling effort has been carried out to simulate the interaction between the edge plasma and the tungsten wall. A new transport code, SolEdge2D–EIRENE, has been developed with the ability to simulate the plasma up to the first wall. This is especially important for steady state operation, where thermal loads on all the plasma facing components, even remote from the plasma, are of interest. Moreover, main chamber tungsten sources are thought to dominate the contamination of the plasma core. We present here in particular new developments aimed at improving the description of the interface between the plasma and the wall, namely a way to treat sheath physics in a more faithful way using the output of 1D particle in cell simulations. Moreover, different models for prompt redeposition have been implemented and are compared. The latter is shown to play an important role in the balance between divertor and main chamber sources.

ADX: a high field, high power density, advanced divertor and RF tokamak

Abstract: The MIT Plasma Science and Fusion Center and collaborators are proposing a high-performance Advanced Divertor and RF tokamak eXperiment (ADX)-a tokamak specifically designed to address critical gaps in the world fusion research programme on the pathway to next-step devices: fusion nuclear science facility (FNSF), fusion pilot plant (FPP) and/or demonstration power plant (DEMO). This high-field (>= 6.5 T, 1.5 MA), high power density facility (P/S similar to 1.5 MW m(-2)) will test innovative divertor ideas, including an 'X-point target divertor' concept, at the required performance parameters-reactor-level boundary plasma pressures, magnetic field strengths and parallel heat flux densities entering into the divertor region-while simultaneously producing high-performance core plasma conditions that are prototypical of a reactor: equilibrated and strongly coupled electrons and ions, regimes with low or no torque, and no fuelling from external heating and current drive systems. Equally important, the experimental platform will test innovative concepts for lower hybrid current drive and ion cyclotron range of frequency actuators with the unprecedented ability to deploy launch structures both on the low-magnetic-field side and the high-magneticfield side-the latter being a location where energetic plasma-material interactions can be controlled and favourable RF wave physics leads to efficient current drive, current profile control, heating and flow drive. This triple combination-advanced divertors, advanced RF actuators, reactor-prototypical core plasma conditions-will enable ADX to explore enhanced core confinement physics, such as made possible by reversed central shear, using only the types of external drive systems that are considered viable for a fusion power plant. Such an integrated demonstration of high-performance core-divertor operation with steady-state sustainment would pave the way towards an attractive pilot plant, as envisioned in the ARC concept (affordable, robust, compact) (Sorbom et al 2015 Fusion Eng. Des. submitted (arXiv: 1409.3540)) that makes use of high-temperature superconductor technology-a high-field (9.25 T) tokamak the size of the Joint European Torus that produces 270 MW of net electricity.

Evaluation of CFETR as a Fusion Nuclear Science Facility using multiple system codes

Abstract: This paper presents the results of a multi-system codes benchmarking study of the recently published China Fusion Engineering Test Reactor (CFETR) pre-conceptual design (Wan et al 2014 IEEE Trans. Plasma Sci. 42 495). Two system codes, General Atomics System Code (GASC) and Tokamak Energy System Code (TESC), using different methodologies to arrive at CFETR performance parameters under the same CFETR constraints show that the correlation between the physics performance and the fusion performance is consistent, and the computed parameters are in good agreement. Optimization of the first wall surface for tritium breeding and the minimization of the machine size are highly compatible. Variations of the plasma currents and profiles lead to changes in the required normalized physics performance, however, they do not significantly affect the optimized size of the machine. GASC and TESC have also been used to explore a lower aspect ratio, larger volume plasma taking advantage of the engineering flexibility in the CFETR design. Assuming the ITER steady-state scenario physics, the larger plasma together with a moderately higher BT and Ip can result in a high gain Qfus ~ 12, Pfus ~ 1 GW machine approaching DEMO-like performance. It is concluded that the CFETR baseline mode can meet the minimum goal of the Fusion Nuclear Science Facility (FNSF) mission and advanced physics will enable it to address comprehensively the outstanding critical technology gaps on the path to a demonstration reactor (DEMO). Before proceeding with CFETR construction steady-state operation has to be demonstrated, further development is needed to solve the divertor heat load issue, and blankets have to be designed with tritium breeding ratio (TBR) >1 as a target.

Compatibility of internal transport barrier with steady-state operation in the high bootstrap fraction regime on DIII-D

Abstract: Recent EAST/DIII-D joint experiments on the high poloidal beta tokamak regime in DIII-D have demonstrated fully noninductive operation with an internal transport barrier (ITB) at large minor radius, at normalized fusion performance increased by ≥30% relative to earlier work (Politzer et al 2005 Nucl. Fusion 45 417). The advancement was enabled by improved understanding of the 'relaxation oscillations', previously attributed to repetitive ITB collapses, and of the fast ion behavior in this regime. It was found that the 'relaxation oscillations' are coupled core-edge modes amenable to wall-stabilization, and that fast ion losses which previously dictated a large plasma-wall separation to avoid wall over-heating, can be reduced to classical levels with sufficient plasma density. By using optimized waveforms of the plasma-wall separation and plasma density, fully noninductive plasmas have been sustained for long durations with excellent energy confinement quality, bootstrap fraction ≥80%, , , and . These results bolster the applicability of the high poloidal beta tokamak regime toward the realization of a steady-state fusion reactor.

Pedestal confinement and stability in JET-ILW ELMy H-modes

Abstract: New experiments in 2013–2014 have investigated the physics responsible for the decrease in H-mode pedestal confinement observed in the initial phase of JET-ILW operation (2012 Experimental Campaigns). The effects of plasma triangularity, global beta and neutrals on pedestal confinement and stability have been investigated systematically. The stability of JET-ILW pedestals is analysed in the framework of the peeling–ballooning model and the model assumptions of the pedestal predictive code EPED. Low D neutrals content in the plasma, achieved either by low D2 gas injection rates or by divertor configurations with optimum pumping, and high beta are necessary conditions for good pedestal (and core) performance. In such conditions the pedestal stability is consistent with the peeling–ballooning paradigm. Moderate to high D2 gas rates, required for W control and stable H-mode operation with the ILW, lead to increased D neutrals content in the plasma and additional physics in the pedestal models may be required to explain the onset of the ELM instability. The changes in H-mode performance associated with the change in JET wall composition from C to Be/W point to D neutrals and low-Z impurities playing a role in pedestal stability, elements which are not currently included in pedestal models. These aspects need to be addressed in order to progress towards full predictive capability of the pedestal height.

Beryllium migration in JET ITER-like wall plasmas

Abstract: JET is used as a test bed for ITER, to investigate beryllium migration which connects the lifetime of first-wall components under erosion with tokamak safety, in relation to long-term fuel retention. The (i) limiter and the (ii) divertor configurations have been studied in JET-ILW (JET with a Be first wall and W divertor), and compared with those for the former JET-C (JET with carbon-based plasma-facing components (PFCs)). (i) For the limiter configuration, the Be gross erosion at the contact point was determined in situ by spectroscopy as between 4% (Ein = 35 eV) and more than 100%, caused by Be self-sputtering (Ein = 200 eV). Chemically assisted physical sputtering via BeD release has been identified to contribute to the effective Be sputtering yield, i.e. at Ein = 75 eV, erosion was enhanced by about 1/3 with respect to the bare physical sputtering case. An effective gross yield of 10% is on average representative for limiter plasma conditions, whereas a factor of 2 difference between the gross erosion and net erosion, determined by post-mortem analysis, was found. The primary impurity source in the limiter configuration in JET-ILW is only 25% higher (in weight) than that for the JET-C case. The main fraction of eroded Be stays within the main chamber. (ii) For the divertor configuration, neutral Be and BeD from physically and chemically assisted physical sputtering by charge exchange neutrals and residual ion flux at the recessed wall enter the plasma, ionize and are transported by scrape-off layer flows towards the inner divertor where significant net deposition takes place. The amount of Be eroded at the first wall (21 g) and the Be amount deposited in the inner divertor (28 g) are in fair agreement, though the balancing is as yet incomplete due to the limited analysis of PFCs. The primary impurity source in the JET-ILW is a factor of 5.3 less in comparison with that for JET-C, resulting in lower divertor material deposition, by more than one order of magnitude. Within the divertor, Be performs far fewer re-erosion and transport steps than C due to an energetic threshold for Be sputtering, and inhibits as a result of this the transport to the divertor floor and the pump duct entrance. The target plates in the JET-ILW inner divertor represent at the strike line a permanent net erosion zone, in contrast to the net deposition zone in JET-C with thick carbon deposits on the CFC (carbon-fibre composite) plates. The Be migration identified is consistent with the observed low long-term fuel retention and dust production with the JET-ILW.

Improved confinement in JET high β plasmas with an ITER-like wall

Abstract: The replacement of the JET carbon wall (C-wall) by a Be/W ITER-like wall (ILW) has affected the plasma energy confinement. To investigate this, experiments have been performed with both the C-wall and ILW to vary the heating power over a wide range for plasmas with different shapes. It was found that the power degradation of thermal energy confinement was weak with the ILW; much weaker than the IPB98(y,2) scaling and resulting in an increase in normalized confinement from H98 ~ 0.9 at βN ~ 1.5 to H98 ~ 1.2−1.3 at βN ~ 2.5 − 3.0 as the power was increased (where H98 = τE/τIPB98(y,2) and βN = βTBT/aIP in % T/mMA). This reproduces the general trend in JET of higher normalized confinement in the so-called 'hybrid' domain, where normalized β is typically above 2.5, compared with 'baseline' ELMy H-mode plasmas with βN ~ 1.5 − 2.0. This weak power degradation of confinement, which was also seen with the C-wall experiments at low triangularity, is due to both increased edge pedestal pressure and core pressure peaking at high power. By contrast, the high triangularity C-wall plasmas exhibited elevated H98 over a wide power range with strong, IPB98(y,2)-like, power degradation. This strong power degradation of confinement appears to be linked to an increase in the source of neutral particles from the wall as the power increased, an effect that was not reproduced with the ILW. The reason for the loss of improved confinement domain at low power with the ILW is yet to be clarified, but contributing factors may include changes in the rate of gas injection, wall recycling, plasma composition and radiation. The results presented in this paper show that the choice of wall materials can strongly affect plasma performance, even changing confinement scalings that are relied upon for extrapolation to future devices.

Neoclassical plasma viscosity and transport processes in non-axisymmetric tori

Abstract: Neoclassical transport processes are important to the understanding of plasma confinement physics in doubly periodic magnetized toroidal plasmas, especially, after the impact of the momentum confinement on the particle and energy confinement is recognized. Real doubly periodic tori in general are non-axisymmetric, with symmetric tori as a special case. An eight-moment approach to transport theory with plasma density N, plasma pressure p, mass flow velocity V and heat flow q as independent variables is adopted. Transport processes are dictated by the solutions of the momentum and heat flux balance equations. For toroidal plasma confinement devices, the first order (in the gyro-radius ordering) plasma flows are on the magnetic surface to guarantee good plasma confinement and are thus two-dimensional. Two linearly independent components of the momentum equation are required to determine the flows completely. Once this two-dimensional flow is relaxed, i.e. the momentum equation reaches a steady state, plasmas become ambipolar, and all the transport fluxes are determined through the flux–force relation. The flux–force relation is derived both from the kinetic definitions for the transport fluxes and from the manipulation of the momentum and heat flux balance equations to illustrate the nature of the transport fluxes by examining their corresponding driven forces and their roles in the momentum and heat flux balance equations. Steady-state plasma flows are determined by the components of the stress and heat stress tensors in the momentum and heat flux balance equations. This approach emphasizes the pivotal role of the momentum equation in the transport processes and is particularly useful in modelling plasma flows in experiments. The methodology for neoclassical transport theory is applied to fluctuation-driven transport fluxes in the quasilinear theory to unify these two theories. Experimental observations in tokamaks and stellarators for the physics discussed are presented.

Runaway electron beam generation and mitigation during disruptions at JET-ILW

Abstract: Disruptions are a major operational concern for next generation tokamaks, including ITER. They may generate excessive heat loads on plasma facing components, large electromagnetic forces in the machine structures and several MA of multi-MeV runaway electrons. A more complete understanding of the runaway generation processes and methods to suppress them is necessary to ensure safe and reliable operation of future tokamaks. Runaway electrons were studied at JET-ILW showing that their generation dependencies (accelerating electric field, avalanche critical field, toroidal field, MHD fluctuations) are in agreement with current theories. In addition, vertical stability plays a key role in long runaway beam formation. Energies up to 20 MeV are observed. Mitigation of an incoming runaway electron beam triggered by massive argon injection was found to be feasible provided that the injection takes place early enough in the disruption process. However, suppressing an already accelerated runaway electron beam in the MA range was found to be difficult even with injections of more than 2 kPa.m3 high-Z gases such as krypton or xenon. This may be due to the presence of a cold background plasma weakly coupled to the runaway electron beam which prevents neutrals from penetrating in the electron beam core. Following unsuccessful mitigation attempts, runaway electron impacts on beryllium plasma-facing components were observed, showing localized melting with toroidal asymmetries.

WEST Physics Basis

Abstract: With WEST (Tungsten Environment in Steady State Tokamak) (Bucalossi et al 2014 Fusion Eng. Des. 89 907-12), the Tore Supra facility and team expertise (Dumont et al 2014 Plasma Phys. Control. Fusion 56 075020) is used to pave the way towards ITER divertor procurement and operation. It consists in implementing a divertor configuration and installing ITER-like actively cooled tungsten monoblocks in the Tore Supra tokamak, taking full benefit of its unique long-pulse capability. WEST is a user facility platform, open to all ITER partners. This paper describes the physics basis of WEST: the estimated heat flux on the divertor target, the planned heating schemes, the expected behaviour of the L-H threshold and of the pedestal and the potential W sources. A series of operating scenarios has been modelled, showing that ITER-relevant heat fluxes on the divertor can be achieved in WEST long pulse H-mode plasmas.

Overview of the JET results

Abstract: Since the installation of an ITER-like wall, the JET programme has focused on the consolidation of ITER design choices and the preparation for ITER operation, with a specific emphasis given to the bulk tungsten melt experiment, which has been crucial for the final decision on the material choice for the day-one tungsten divertor in ITER. Integrated scenarios have been progressed with the re-establishment of long-pulse, high-confinement H-modes by optimizing the magnetic configuration and the use of ICRH to avoid tungsten impurity accumulation. Stationary discharges with detached divertor conditions and small edge localized modes have been demonstrated by nitrogen seeding. The differences in confinement and pedestal behaviour before and after the ITER-like wall installation have been better characterized towards the development of high fusion yield scenarios in DT. Post-mortem analyses of the plasma-facing components have confirmed the previously reported low fuel retention obtained by gas balance and shown that the pattern of deposition within the divertor has changed significantly with respect to the JET carbon wall campaigns due to the absence of thermally activated chemical erosion of beryllium in contrast to carbon. Transport to remote areas is almost absent and two orders of magnitude less material is found in the divertor.

Overview of ECR plasma heating experiment in the GDT magnetic mirror

Abstract: This paper summarizes the results of experiments on electron cyclotron resonance heating (ECRH) of plasma obtained at the axially symmetric magnetic mirror device gas dynamic trap (GDT) (Budker Institute, Novosibirsk). The main achievement is the demonstration of plasma discharges with extremely high temperatures of bulk electrons. According to the Thomson scattering measurements, the on-axis electron temperature averaged over several sequential shots is 660 ± 50 eV with peak values exceeding 900 eV in a few shots. This corresponds to an at least threefold increase as compared to previous experiments both at the GDT and at other comparable machines, thus demonstrating the maximum quasi-stationary (~0.6 ms) electron temperature achieved in open traps. The breakthrough is made possible with the successful implementation of a sophisticated ECRH scheme in addition to standard heating by neutral beams (NBs). Another important result is the demonstration of the significantly increased lifetime of NB-driven fast particles with the application of ECRH, leading to a 30% higher plasma energy content at the end of the discharge. All available data including the previously demonstrated possibility of plasma confinement with β as high as 60%, allows us to consider fusion applications of axially symmetric magnetic mirror machines on a realistic basis.

ELM-induced transient tungsten melting in the JET divertor

Abstract: The original goals of the JET ITER-like wall included the study of the impact of an all W divertor on plasma operation (Coenen et al 2013 Nucl. Fusion 53 073043) and fuel retention (Brezinsek et al 2013 Nucl. Fusion 53 083023). ITER has recently decided to install a full-tungsten (W) divertor from the start of operations. One of the key inputs required in support of this decision was the study of the possibility of W melting and melt splashing during transients. Damage of this type can lead to modifications of surface topology which could lead to higher disruption frequency or compromise subsequent plasma operation. Although every effort will be made to avoid leading edges, ITER plasma stored energies are sufficient that transients can drive shallow melting on the top surfaces of components. JET is able to produce ELMs large enough to allow access to transient melting in a regime of relevance to ITER. Transient W melt experiments were performed in JET using a dedicated divertor module and a sequence of I-P = 3.0 MA/B-T = 2.9 T H-mode pulses with an input power of P-IN = 23 MW, a stored energy of similar to 6 MJ and regular type I ELMs at Delta W-ELM = 0.3 MJ and f(ELM) similar to 30 Hz. By moving the outer strike point onto a dedicated leading edge in the W divertor the base temperature was raised within similar to 1 s to a level allowing transient, ELM-driven melting during the subsequent 0.5 s. Such ELMs (delta W similar to 300 kJ per ELM) are comparable to mitigated ELMs expected in ITER (Pitts et al 2011 J. Nucl. Mater. 415 (Suppl.) S957-64). Although significant material losses in terms of ejections into the plasma were not observed, there is indirect evidence that some small droplets (similar to 80 mu m) were released. Almost 1 mm (similar to 6 mm(3)) of W was moved by similar to 150 ELMs within 7 subsequent discharges. The impact on the main plasma parameters was minor and no disruptions occurred. The W-melt gradually moved along the leading edge towards the high-field side, driven by j x B forces. The evaporation rate determined from spectroscopy is 100 times less than expected from steady state melting and is thus consistent only with transient melting during the individual ELMs. Analysis of IR data and spectroscopy together with modelling using the MEMOS code Bazylev et al 2009 J. Nucl. Mater. 390-391 810-13 point to transient melting as the main process. 3D MEMOS simulations on the consequences of multiple ELMs on damage of tungsten castellated armour have been performed. These experiments provide the first experimental evidence for the absence of significant melt splashing at transient events resembling mitigated ELMs on ITER and establish a key experimental benchmark for the MEMOS code.

Key impact of finite-beta and fast ions in core and edge tokamak regions for the transition to advanced scenarios

Abstract: Extensive linear and non-linear gyrokinetic simulations and linear magnetohydrodynamic (MHD) analyses performed for JET hybrid discharges with improved confinement have shown that the large population of fast ions found in the plasma core under particular heating conditions has a strong impact on core microturbulence and edge MHD by reducing core ion heat fluxes and increasing pedestal pressure in a feedback mechanism. In the case of the ITER like wall, it is shown how this mechanism plays a decisive role for the transition to plasma regimes with improved confinement and it can explain the weak power degradation obtained in dedicated power scans. The mechanism is found to be highly dependent on plasma triangularity as it changes the balance between the improvement in the plasma core and the edge. The feedback mechanism can play a similar role in the ITER hybrid scenario as in the JET discharges analysed due to its high triangularity plasmas and the large amount of fast ions generated in the core by the heating systems and the alpha power.

The accomplishment of the Engineering Design Activities of IFMIF/EVEDA: The European - Japanese project towards a Li(d,xn) fusion relevant neutron source

Abstract: The International Fusion Materials Irradiation Facility (IFMIF), presently in its Engineering Validation and Engineering Design Activities (EVEDA) phase under the frame of the Broader Approach Agreement between Europe and Japan, accomplished in summer 2013, on schedule, its EDA phase with the release of the engineering design report of the IFMIF plant, which is here described. Many improvements of the design from former phases are implemented, particularly a reduction of beam losses and operational costs thanks to the superconducting accelerator concept, the re-location of the quench tank outside the test cell (TC) with a reduction of tritium inventory and a simplification on its replacement in case of failure, the separation of the irradiation modules from the shielding block gaining irradiation flexibility and enhancement of the remote handling equipment reliability and cost reduction, and the water cooling of the liner and biological shielding of the TC, enhancing the efficiency and economy of the related sub-systems. In addition, the maintenance strategy has been modified to allow a shorter yearly stop of the irradiation operations and a more careful management of the irradiated samples. The design of the IFMIF plant is intimately linked with the EVA phase carried out since the entry into force of IFMIF/EVEDA in June 2007. These last activities and their on-going accomplishment have been thoroughly described elsewhere (Knaster J et al [19]), which, combined with the present paper, allows a clear understanding of the maturity of the European–Japanese international efforts. This released IFMIF Intermediate Engineering Design Report (IIEDR), which could be complemented if required concurrently with the outcome of the on-going EVA, will allow decision making on its construction and/or serve as the basis for the definition of the next step, aligned with the evolving needs of our fusion community.

Edge and SOL turbulence and blob variations over a large database in NSTX

Abstract: This paper describes the range of variations in edge and SOL turbulence observed using a gas puff imaging (GPI) diagnostic in NSTX discharges. The database consists of 140 shots including Ohmic, L-mode, and H-mode plasmas measured during steady-state conditions (e.g. without ELMs). Turbulence quantities were evaluated using both cross-correlation analysis and blob tracking. Relative fluctuation levels varied from –1.0, correlation times were –40 μs, correlation lengths were –10 cm, and turbulence velocities were km s−1 and km s−1 outwards. These variations were evaluated with respect to both the global and local edge plasma parameters, and compared with simplified theoretical models.

Towards an emerging understanding of non-locality phenomena and non-local transport

Abstract: In this paper, recent progress on experimental analysis and theoretical models for non-local transport (non-Fickian fluxes in real space) is reviewed. The non-locality in the heat and momentum transport observed in the plasma, the departures from linear flux-gradient proportionality, and externally triggered non-local transport phenomena are described in both L-mode and improved-mode plasmas. Ongoing evaluation of ‘fast front’ and ‘intrinsically non-local’ models, and their success in comparisons with experimental data, are discussed

Non-axisymmetric magnetic fields and toroidal plasma confinement

Abstract: The physics of non-axisymmetry is a far more important topic in the theory of toroidal fusion plasmas than might be expected. (1) Even a small toroidal asymmetry in the magnetic field strength, ?????ln?B/?????10?4, can cause an unacceptable degradation in performance. (2) Nevertheless, asymmetries?even large asymmetries ????1?can give beneficial plasma control and circumvent issues, such as magnetic-configuration maintenance and plasma disruptions, that make axisymmetric fusion devices problematic. Viewed from prospectives that are adequate for designing and studying axisymmetric plasmas, the physics of non-axisymmetric plasmas appears dauntingly difficult. Remarkably, Maxwell's equations provide such strong constraints on the physics of toroidal fusion plasmas that even a black-box model of a plasma answers many important questions. Kinetic theory and non-equilibrium thermodynamics provide further, but more nuanced, constraints. This paper is organized so these constraints can be used as a basis for the innovations and for the extrapolations that are required to go from existing experiments to fusion systems. Outlines are given of a number of calculations that would be of great importance to ITER and to the overall fusion program and that could be carried out now with limited resources.