Journal ArticleDOI
A model for wear rates of composite coatings
Reads0
Chats0
TLDR
In this paper, a model for wear rates of polymer-based composites is applied to predict the wear rate of nickel-silicon nitride composite coatings under sliding conditions.About:
This article is published in Wear.The article was published on 1992-07-30. It has received 8 citations till now. The article focuses on the topics: Nitride & Composite number.read more
Citations
More filters
Journal ArticleDOI
Fundamental aspects and recent progress on wear/scratch damage in polymer nanocomposites
TL;DR: In this paper, a review of the wear and scratch properties of polymer nanocomposites is presented, focusing on their wear (in dry sliding and unlubricated conditions) and scratch damage, showing that it is not valid to assume that nano-fillers always improve wear/scratch (and friction) properties.
Journal ArticleDOI
Wear behavior of hot extruded Al6061 based composites
C.S. Ramesh,Mir Safiulla +1 more
TL;DR: In this article, the wear behavior of hot extruded Al6061 based composites has been investigated, where SiC, Al 2 O 3 and cerium oxide have been used as reinforcements.
Journal ArticleDOI
Tribological characteristics of nickel based composite coatings
C.S. Ramesh,S. K. Seshadri +1 more
TL;DR: In this paper, a theoretical model was used to predict the wear rates of the composite coatings and the predicted wear rates were in reasonable agreement with the experimental values, however, they did not consider the effect of load and sliding speed on both the coefficient of friction and wear rates.
Journal ArticleDOI
Dry sliding wear behaviour of nickel-, iron- and cobalt-based superalloys
TL;DR: In this paper, the performance of NiO-based superalloys has been investigated using a pin-on-disc wear test rig, and the worn samples were analysed with XRD and SEM.
Journal ArticleDOI
Synthesis and characterisation of hot extruded aluminium-based MMC developed by powder metallurgy route
TL;DR: In this paper, the effect of hot extrusion on mechanical and tribological characteristics of AMCs developed by powder metallurgy route followed by double axial cold compaction and controlled atmospheric sintering was studied.
References
More filters
Book ChapterDOI
Friction and wear of polymer composites
X.Q. Pei,Klaus Friedrich +1 more
TL;DR: In this paper, the effects of various fillers on the wear and friction of PTFE-based composites are discussed. And the wear properties of metal matrix-graphite fiber composites (M. Tsukizoe, N. Ohmae, and Z. Eliezer).
Journal ArticleDOI
On the wear behaviour of short-fibre-reinforced peek composites
H. Voss,Klaus Friedrich +1 more
TL;DR: In this paper, the wear behavior of short-glass and carbon-fibre-reinforced composites of polyetheretherketone is investigated under extremely different types of wear loading.
Journal ArticleDOI
Friction and Wear of Hot Pressed Silicon Nitride and Other Ceramics
TL;DR: In this paper, an investigation was conducted to determine the friction and wear characteristics of hot-pressed silicon nitride surfaces, and the results of the wear experiments indicated that residual α-silicon nitride was transformed into β-silicon oxide, which reduced both the wear rate and friction.
Journal ArticleDOI
Abrasive wear of particle-filled polymers
S. V. Prasad,Paul Calvert +1 more
TL;DR: In this article, the abrasive wear rates of quartz and glass particle-reinforced PMMA have been measured as a function of filler volume fraction for silicon carbide, quartz and calcite abrasives.
Journal ArticleDOI
Wear performance of a bulk liquid crystal polymer and its short-fibre composites
H. Voss,K. Friedrich +1 more
TL;DR: In this paper, the wear behavior of short-fibre reinforced composites having a liquid crystal polymer (LCP) matrix was investigated under two extremely different types of wear loading.
Related Papers (5)
Three-body abrasive wear of composite coatings in dry and wet environments
Dry sliding wear behavior of molybdenum alloyed sintered steels
Jun’an Wang,Herbert Danninger +1 more