scispace - formally typeset
Search or ask a question
Journal ArticleDOI

Analysis of crack formation and crack growth in concrete by means of fracture mechanics and finite elements

01 Nov 1976-Cement and Concrete Research (American Concrete Institute)-Vol. 6, Iss: 6, pp 773-781
TL;DR: In this article, fracture mechanics is introduced into finite element analysis by means of a model where stresses are assumed to act across a crack as long as it is narrowly opened, which may be regarded as a way of expressing the energy adsorption in the energy balance approach.
About: This article is published in Cement and Concrete Research.The article was published on 1976-11-01. It has received 5505 citations till now. The article focuses on the topics: Crack growth resistance curve & Fracture mechanics.
Citations
More filters
Journal ArticleDOI
01 May 1983
TL;DR: In this article, a fracture theory for a heterogenous aggregate material which exhibits a gradual strain-softening due to microcracking and contains aggregate pieces that are not necessarily small compared to structural dimensions is developed.
Abstract: A fracture theory for a heterogenous aggregate material which exhibits a gradual strain-softening due to microcracking and contains aggregate pieces that are not necessarily small compared to structural dimensions is developed. Only Mode I is considered. The fracture is modeled as a blunt smeard crack band, which is justified by the random nature of the microstructure. Simple triaxial stress-strain relations which model the strain-softening and describe the effect of gradual microcracking in the crack band are derived. It is shown that it is easier to use compliance rather than stiffness matrices and that it suffices to adjust a single diagonal term of the complicance matrix. The limiting case of this matrix for complete (continuous) cracking is shown to be identical to the inverse of the well-known stiffness matrix for a perfectly cracked material. The material fracture properties are characterized by only three parameters—fracture energy, uniaxial strength limit and width of the crack band (fracture process zone), while the strain-softening modulus is a function of these parameters. A method of determining the fracture energy from measured complete stres-strain relations is also given. Triaxial stress effects on fracture can be taken into account. The theory is verified by comparisons with numerous experimental data from the literature. Satisfactory fits of maximum load data as well as resistance curves are achieved and values of the three material parameters involved, namely the fracture energy, the strength, and the width of crack band front, are determined from test data. The optimum value of the latter width is found to be about 3 aggregate sizes, which is also justified as the minimum acceptable for a homogeneous continuum modeling. The method of implementing the theory in a finite element code is also indicated, and rules for achieving objectivity of results with regard to the analyst's choice of element size are given. Finally, a simple formula is derived to predict from the tensile strength and aggregate size the fracture energy, as well as the strain-softening modulus. A statistical analysis of the errors reveals a drastic improvement compared to the linear fracture theory as well as the strength theory. The applicability of fracture mechanics to concrete is thus solidly established.

3,102 citations

Journal ArticleDOI
TL;DR: In this article, a constitutive model based on an internal variable-formulation of plasticity theory for the non-linear analysis of concrete is presented, which uses a new yield criterion which matches experimental data quite well and it accounts for both elastic and plastic stiffness degradations effects.

3,080 citations

Journal ArticleDOI
TL;DR: In this paper, the authors proposed a nonlocal damage theory, which is based on the nonlocal treatment of damage from the local treatment of elastic behavior, and the only required modification is to replace the usual local damage energy release rate with its spatial average over the representative volume of the material whose size is a characteristic of a material.
Abstract: In the usual local finite element analysis, strain softening causes spurious mesh sensitivity and incorrect convergence when the element is refined to vanishing size. In a previous continuum formulation, these incorrect features were overcome by the imbricate nonlocal continuum, which, however, introduced some unnecessary computational complications due to the fact that all response was treated as nonlocal. The key idea of the present nonlocal damage theory is to subject to nonlocal treatment only those variables that control strain softening, and to treat the elastic part of the strain as local. The continuum damage mechanics formulation, convenient for separating the nonlocal treatment of damage from the local treatment of elastic behavior, is adopted in the present work. The only required modification is to replace the usual local damage energy release rate with its spatial average over the representative volume of the material whose size is a characteristic of the material. Avoidance of spurious mesh ...

1,672 citations

Journal ArticleDOI
TL;DR: In this article, the authors studied the structural size effect of fracture in concrete and rock structures, using dimensional analysis and illustrative examples, and showed that the energy release caused by fracture depends on both the length and the area of the crack band.
Abstract: The fracture front in concrete, as well as rock, is blunted by a zone of microcracking, and in ductile metals by a zone of yielding. This blunting causes deviations from the structural size effect known from linear elastic fracture mechanics (LEFM). The size effect is studied first for concrete or rock structures, using dimensional analysis and illustrative examples. Fracture is considered to be caused by propagation of a crack band that has a fixed width at its front relative to the aggregate size. The analysis rests on the hypothesis that the energy release caused by fracture depends on both the length and the area of the crack band. The size effect is shown to consist in a smooth transition from the strength criterion for small sizes to LEFM for large sizes, and the nominal stress σN at failure is found to decline as (1+λ/λ0)-1/2 in which λ0=constant and λ=relative structure size. This function is verified by Walsh's test data. If reinforcement is present at the fracture front and behaves elastically, ...

1,474 citations

Journal ArticleDOI
TL;DR: In this article, an extended finite element method is applied to modeling growth of arbitrary cohesive cracks, which is governed by requiring the stress intensity factors at the tip of the cohesive zone to vanish.

1,395 citations

References
More filters