CO2 electroreduction to ethylene via hydroxide-mediated copper catalysis at an abrupt interface
18 May 2018-Science (American Association for the Advancement of Science)-Vol. 360, Iss: 6390, pp 783-787
TL;DR: A copper electrocatalyst at an abrupt reaction interface in an alkaline electrolyte reduces CO2 to ethylene with 70% faradaic efficiency at a potential of −0.55 volts versus a reversible hydrogen electrode (RHE).
Abstract: Carbon dioxide (CO 2 ) electroreduction could provide a useful source of ethylene, but low conversion efficiency, low production rates, and low catalyst stability limit current systems. Here we report that a copper electrocatalyst at an abrupt reaction interface in an alkaline electrolyte reduces CO 2 to ethylene with 70% faradaic efficiency at a potential of −0.55 volts versus a reversible hydrogen electrode (RHE). Hydroxide ions on or near the copper surface lower the CO 2 reduction and carbon monoxide (CO)–CO coupling activation energy barriers; as a result, onset of ethylene evolution at −0.165 volts versus an RHE in 10 molar potassium hydroxide occurs almost simultaneously with CO production. Operational stability was enhanced via the introduction of a polymer-based gas diffusion layer that sandwiches the reaction interface between separate hydrophobic and conductive supports, providing constant ethylene selectivity for an initial 150 operating hours.
Citations
More filters
TL;DR: In this article, the authors discuss the structure-activity-selectivity relations from studies on well-ordered surfaces, i.e., single crystalline electrodes, for the CO2 electroreduction reaction (CO2RR) and summarise the role of the electrolyte.
Abstract: Aiming to reduce anthropogenic CO2 emissions, there is an urgent demand to develop more efficient and affordable technologies which convert CO2 into valuable feedstock molecules. The use of renewable electricity is a promising and sustainable approach to overcome this environmental issue, while producing valuable chemicals and clean fuels. However, the CO2 electroreduction reaction (CO2RR) still shows two main gaps: poor selectivity and required large overpotentials make the process not profitable enough. To overcome these challenges, model studies on single‐crystalline surfaces aiming to find the relations between surface structure/electrolyte interactions and activity/selectivity are necessary. In these model studies, tuning the electrolyte composition is also key for the fundamental understanding of the CO2RR. In this review, we first discuss the structure‐activity‐selectivity relations from studies on well‐ordered surfaces, i. e., single crystalline electrodes, for the CO2RR. We then summarise the role of the electrolyte, presenting work on classical aqueous solvents as well as non‐aqueous electrolytes such as ionic liquids. We illustrate the importance of carrying out studies on well‐defined electrified interfaces in order to get deep fundamental insights on the mechanism of the CO2RR, as well as scaling the process for real applications. Ultimately, this knowledge will be essential to rationally design the catalyst with tailored activity and selectivity for CO2 reduction.
59 citations
TL;DR: In this paper, single-crystalline Bi rhombic dodecahedrons (RDs) exposed with (104) and (110) facets are developed, which demonstrate a very low overpotential and high selectivity for formate production (Faradic efficiency >92.2%).
Abstract: Bismuth (Bi) is a topological crystalline insulator (TCI), which has gapless topological surface states (TSSs) protected by a specific crystalline symmetry that strongly depends on the facet. Bi is also a promising electrochemical CO2 reduction reaction (ECO2 RR) electrocatalyst for formate production. In this study, single-crystalline Bi rhombic dodecahedrons (RDs) exposed with (104) and (110) facets are developed. The Bi RDs demonstrate a very low overpotential and high selectivity for formate production (Faradic efficiency >92.2%) in a wide partial current density range from 9.8 to 290.1 mA cm-2 , leading to a remarkably high full-cell energy efficiency (69.5%) for ECO2 RR. The significantly reduced overpotential is caused by the enhanced *OCHO adsorption on the Bi RDs. The high selectivity of formate can be ascribed to the TSSs and the trivial surface states opening small gaps in the bulk gap on Bi RDs, which strengthens and stabilizes the preferentially adsorbed *OCHO and mitigates the competing adsorption of *H during ECO2 RR. This study describes a promising application of Bi RDs for high-rate formate production and high-efficiency energy storage of intermittent renewable electricity. Optimizing the geometry of TCIs is also proposed as an effective strategy to tune the TSSs of topological catalysts.
59 citations
TL;DR: In this paper, a simple yet robust double-solvent-induced self-assembly strategy is developed to yield supramolecular precursors using a single monomer for crafting one-dimensional (1D), highly porous g-C3N4 microtubes that possess remarkable photocatalytic CO2 conversion performance.
59 citations
TL;DR: Most CO2 utilization technologies are at low technology readiness levels (TRLs), and screening to identify the most promising technologies should be conducted before allocating large RD co-electrolysis of CO2 and water for ethylene production as discussed by the authors.
59 citations
TL;DR: In this article, B-doped Cu (B-Cu) and B-Cu-Zn gas diffusion electrodes (GDEs) were developed for highly selective and stable CO2 conversion to C2+ products at industrially relevant current densities.
Abstract: Electroreduction of CO2 to multi-carbon products has attracted considerable attention as it provides an avenue to high-density renewable energy storage However, the selectivity and stability under high current densities are rarely reported Herein, B-doped Cu (B-Cu) and B-Cu-Zn gas diffusion electrodes (GDE) were developed for highly selective and stable CO2 conversion to C2+ products at industrially relevant current densities The B-Cu GDE exhibited a high Faradaic efficiency of 79 % for C2+ products formation at a current density of -200 mA cm-2 and a potential of -045 V vs RHE The long-term stability for C2+ formation was substantially improved by incorporating an optimal amount of Zn Operando Raman spectra confirm the retained Cu+ species under CO2 reduction conditions and the lower overpotential for *OCO formation upon incorporation of Zn, which lead to the excellent conversion of CO2 to C2+ products on B-Cu-Zn GDEs
58 citations
References
More filters
TL;DR: A simple derivation of a simple GGA is presented, in which all parameters (other than those in LSD) are fundamental constants, and only general features of the detailed construction underlying the Perdew-Wang 1991 (PW91) GGA are invoked.
Abstract: Generalized gradient approximations (GGA’s) for the exchange-correlation energy improve upon the local spin density (LSD) description of atoms, molecules, and solids. We present a simple derivation of a simple GGA, in which all parameters (other than those in LSD) are fundamental constants. Only general features of the detailed construction underlying the Perdew-Wang 1991 (PW91) GGA are invoked. Improvements over PW91 include an accurate description of the linear response of the uniform electron gas, correct behavior under uniform scaling, and a smoother potential. [S0031-9007(96)01479-2] PACS numbers: 71.15.Mb, 71.45.Gm Kohn-Sham density functional theory [1,2] is widely used for self-consistent-field electronic structure calculations of the ground-state properties of atoms, molecules, and solids. In this theory, only the exchange-correlation energy EXC › EX 1 EC as a functional of the electron spin densities n"srd and n#srd must be approximated. The most popular functionals have a form appropriate for slowly varying densities: the local spin density (LSD) approximation Z d 3 rn e unif
146,533 citations
TL;DR: An efficient scheme for calculating the Kohn-Sham ground state of metallic systems using pseudopotentials and a plane-wave basis set is presented and the application of Pulay's DIIS method to the iterative diagonalization of large matrices will be discussed.
Abstract: We present an efficient scheme for calculating the Kohn-Sham ground state of metallic systems using pseudopotentials and a plane-wave basis set. In the first part the application of Pulay's DIIS method (direct inversion in the iterative subspace) to the iterative diagonalization of large matrices will be discussed. Our approach is stable, reliable, and minimizes the number of order ${\mathit{N}}_{\mathrm{atoms}}^{3}$ operations. In the second part, we will discuss an efficient mixing scheme also based on Pulay's scheme. A special ``metric'' and a special ``preconditioning'' optimized for a plane-wave basis set will be introduced. Scaling of the method will be discussed in detail for non-self-consistent and self-consistent calculations. It will be shown that the number of iterations required to obtain a specific precision is almost independent of the system size. Altogether an order ${\mathit{N}}_{\mathrm{atoms}}^{2}$ scaling is found for systems containing up to 1000 electrons. If we take into account that the number of k points can be decreased linearly with the system size, the overall scaling can approach ${\mathit{N}}_{\mathrm{atoms}}$. We have implemented these algorithms within a powerful package called VASP (Vienna ab initio simulation package). The program and the techniques have been used successfully for a large number of different systems (liquid and amorphous semiconductors, liquid simple and transition metals, metallic and semiconducting surfaces, phonons in simple metals, transition metals, and semiconductors) and turned out to be very reliable. \textcopyright{} 1996 The American Physical Society.
81,985 citations
TL;DR: In this paper, the formal relationship between US Vanderbilt-type pseudopotentials and Blochl's projector augmented wave (PAW) method is derived and the Hamilton operator, the forces, and the stress tensor are derived for this modified PAW functional.
Abstract: The formal relationship between ultrasoft (US) Vanderbilt-type pseudopotentials and Bl\"ochl's projector augmented wave (PAW) method is derived. It is shown that the total energy functional for US pseudopotentials can be obtained by linearization of two terms in a slightly modified PAW total energy functional. The Hamilton operator, the forces, and the stress tensor are derived for this modified PAW functional. A simple way to implement the PAW method in existing plane-wave codes supporting US pseudopotentials is pointed out. In addition, critical tests are presented to compare the accuracy and efficiency of the PAW and the US pseudopotential method with relaxed core all electron methods. These tests include small molecules $({\mathrm{H}}_{2}{,\mathrm{}\mathrm{H}}_{2}{\mathrm{O},\mathrm{}\mathrm{Li}}_{2}{,\mathrm{}\mathrm{N}}_{2}{,\mathrm{}\mathrm{F}}_{2}{,\mathrm{}\mathrm{BF}}_{3}{,\mathrm{}\mathrm{SiF}}_{4})$ and several bulk systems (diamond, Si, V, Li, Ca, ${\mathrm{CaF}}_{2},$ Fe, Co, Ni). Particular attention is paid to the bulk properties and magnetic energies of Fe, Co, and Ni.
57,691 citations
TL;DR: An improved way of estimating the local tangent in the nudged elastic band method for finding minimum energy paths is presented, and examples given where a complementary method, the dimer method, is used to efficiently converge to the saddle point.
Abstract: An improved way of estimating the local tangent in the nudged elastic band method for finding minimum energy paths is presented. In systems where the force along the minimum energy path is large compared to the restoring force perpendicular to the path and when many images of the system are included in the elastic band, kinks can develop and prevent the band from converging to the minimum energy path. We show how the kinks arise and present an improved way of estimating the local tangent which solves the problem. The task of finding an accurate energy and configuration for the saddle point is also discussed and examples given where a complementary method, the dimer method, is used to efficiently converge to the saddle point. Both methods only require the first derivative of the energy and can, therefore, easily be applied in plane wave based density-functional theory calculations. Examples are given from studies of the exchange diffusion mechanism in a Si crystal, Al addimer formation on the Al(100) surfa...
6,825 citations
TL;DR: This paper describes how accurate off-lattice ascent paths can be represented with respect to the grid points, and maintains the efficient linear scaling of an earlier version of the algorithm, and eliminates a tendency for the Bader surfaces to be aligned along the grid directions.
Abstract: A computational method for partitioning a charge density grid into Bader volumes is presented which is efficient, robust, and scales linearly with the number of grid points. The partitioning algorithm follows the steepest ascent paths along the charge density gradient from grid point to grid point until a charge density maximum is reached. In this paper, we describe how accurate off-lattice ascent paths can be represented with respect to the grid points. This improvement maintains the efficient linear scaling of an earlier version of the algorithm, and eliminates a tendency for the Bader surfaces to be aligned along the grid directions. As the algorithm assigns grid points to charge density maxima, subsequent paths are terminated when they reach previously assigned grid points. It is this grid-based approach which gives the algorithm its efficiency, and allows for the analysis of the large grids generated from plane-wave-based density functional theory calculations.
5,417 citations