Book•
Dynamic Behavior of Materials
27 Sep 1994-
TL;DR: In this paper, the authors present a method to produce dynamic deformation at high strain rates by using Shear Bands (Thermoplastic Shear Instabilities) and dynamic fracture.
Abstract: Dynamic Deformation and Waves. Elastic Waves. Plastic Waves. Shock Waves. Shock Waves: Equations of State. Differential Form of Conservation Equations and Numerical Solutions to More Complex Problems. Shock Wave Attenuation, Interaction, and Reflection. Shock Wave-Induced Phase Transformations and Chemical Changes. Explosive-Material Interactions. Detonation. Experimental Techniques: Diagnostic Tools. Experimental Techniques: Methods to Produce Dynamic Deformation. Plastic Deformation at High Strain Rates. Plastic Deformation in Shock Waves. Shear Bands (Thermoplastic Shear Instabilities). Dynamic Fracture. Applications. Indexes.
Citations
More filters
TL;DR: The tensile strengths of individual multiwalled carbon nanotubes (MWCNTs) were measured with a "nanostressing stage" located within a scanning electron microscope and a variety of structures were revealed, such as a nanotube ribbon, a wave pattern, and partial radial collapse.
Abstract: The tensile strengths of individual multiwalled carbon nanotubes (MWCNTs) were measured with a “nanostressing stage” located within a scanning electron microscope. The tensile-loading experiment was prepared and observed entirely within the microscope and was recorded on video. The MWCNTs broke in the outermost layer (“sword-in-sheath” failure), and the tensile strength of this layer ranged from 11 to 63 gigapascals for the set of 19 MWCNTs that were loaded. Analysis of the stress-strain curves for individual MWCNTs indicated that the Young's modulus E of the outermost layer varied from 270 to 950 gigapascals. Transmission electron microscopic examination of the broken nanotube fragments revealed a variety of structures, such as a nanotube ribbon, a wave pattern, and partial radial collapse.
5,011 citations
TL;DR: A review of the development and the state of the art in dynamic testing techniques and dynamic mechanical behaviour of rock materials can be found in this article, where a detailed description of various dynamic mechanical properties (e.g., uniaxial and triaxial compressive strength, tensile strength, shear strength and fracture toughness) and corresponding fracture behaviour are discussed.
Abstract: The purpose of this review is to discuss the development and the state of the art in dynamic testing techniques and dynamic mechanical behaviour of rock materials. The review begins by briefly introducing the history of rock dynamics and explaining the significance of studying these issues. Loading techniques commonly used for both intermediate and high strain rate tests and measurement techniques for dynamic stress and deformation are critically assessed in Sects. 2 and 3. In Sect. 4, methods of dynamic testing and estimation to obtain stress–strain curves at high strain rate are summarized, followed by an in-depth description of various dynamic mechanical properties (e.g. uniaxial and triaxial compressive strength, tensile strength, shear strength and fracture toughness) and corresponding fracture behaviour. Some influencing rock structural features (i.e. microstructure, size and shape) and testing conditions (i.e. confining pressure, temperature and water saturation) are considered, ending with some popular semi-empirical rate-dependent equations for the enhancement of dynamic mechanical properties. Section 5 discusses physical mechanisms of strain rate effects. Section 6 describes phenomenological and mechanically based rate-dependent constitutive models established from the knowledge of the stress–strain behaviour and physical mechanisms. Section 7 presents dynamic fracture criteria for quasi-brittle materials. Finally, a brief summary and some aspects of prospective research are presented.
781 citations
Cites methods from "Dynamic Behavior of Materials"
...In this study, impact loading studies are not included; the interested reader is referred to the excellent book by Meyers (1994) and critical review by Field et al. (2004) for the general principle and experimental techniques, and a recent PhD thesis (Braithwaite 2009) for knowledge of impact…...
[...]
TL;DR: In this paper, a variety of techniques used to obtain the mechanical properties of materials at high rates of strain (⩾10 s−1) are summarised, including dropweight machines, split Hopkinson pressure bars, Taylor impact and shock loading by plate impact.
683 citations
Additional excerpts
...[128,130–153]....
[...]
475 citations
TL;DR: In this article, the authors examined the status of the common assumption that β is a constant with regard to the thermodynamic foundations of thermoplasticity and experiments, and showed that β depends strongly on both strain and strain rate for various engineering materials.
Abstract: The energy balance equation for elastoplastic solids includes heat source terms that govern the conversion of some of the plastic work into heat. The remainder contributes to the stored energy of cold work due to the creation of crystal defects. This paper is concerned with the fraction β of the rate of plastic work converted into heating. We examine the status of the common assumption that β is a constant with regard to the thermodynamic foundations of thermoplasticity and experiments. A general internal-variable theory is introduced and restricted to abide by the second law of thermodynamics. Experimentally motivated assumptions reduce this theory to a special model of classical thermoplasticity. The only part of the internal energy not determined from the isothermal response is the stored energy of cold work, a function only of the internal variables. We show that this function can be inferred from stress and temperature data from a single adiabatic straining experiment. Experimental data from dynamic Kolsky-bar tests at various strain rates yield a unique stored energy function. Its knowledge is crucial for the determination of the thermomechanical response in non-isothermal processes. Such a prediction agrees well with results from dynamic tests at different rates. In these experiments, β is found to depend strongly on both strain and strain rate for various engineering materials. The model is successful in predicting this dependence. Requiring β to be constant is thus an approximation of dubious validity.
456 citations