Effects of Al2O3–Cu/water hybrid nanofluid on heat transfer and flow characteristics in turbulent regime
25 Feb 2015-International Journal of Modern Physics C (World Scientific Publishing Company)-Vol. 26, Iss: 04, pp 1550047
TL;DR: In this paper, the authors examined the effects of these three fluids as the working fluids, a wide range of Reynolds number (10 000 ≤ Re ≤ 10 0000) and also the volume concentration (0% ≤ ϕ ≤ 2%) on heat transfer and hydrodynamic performance.
Abstract: In this paper, forced convection of a turbulent flow of pure water, Al2O3/water nanofluid and Al2O3–Cu/water hybrid nanofluid (a new advanced nanofluid composited of Cu and Al2O3 nanoparticles) through a uniform heated circular tube is numerically analyzed. This paper examines the effects of these three fluids as the working fluids, a wide range of Reynolds number (10 000 ≤ Re ≤ 10 0000) and also the volume concentration (0% ≤ ϕ ≤ 2%) on heat transfer and hydrodynamic performance. The finite volume discretization method is employed to solve the set of the governing equations. The results indicate that employing hybrid nanofluid improves the heat transfer rate with respect to pure water and nanofluid, yet it reveals an adverse effect on friction factor and appears severely outweighed by pressure drop penalty. However, the average increase of the average Nusselt number (when compared to pure water) in Al2O3–Cu/water hybrid nanofluid is 32.07% and the amount for the average increase of friction factor would be 13.76%.
Citations
More filters
TL;DR: In this paper, a review summarizes the contemporary investigations on synthesis, thermo-physical properties, heat transfer characteristics, hydrodynamic behavior and fluid flow characteristics reported by researchers on different hybrid nanofluids.
Abstract: Nanofluids have found crucial presence in heat transfer applications with their promising characteristics that can be controlled as per requirements. Nanofluids possess unique characteristics that have attracted many researchers over the past two decades to design new thermal systems for different engineering applications. Mono nanofluids, prepared with a single kind of nanoparticles, possess certain specific benefits owing to the properties of the suspended nanoparticle. However to further improve the characteristics of nanofluids, that could possess a number of favourable characteristics, researchers developed a new generation heat transfer fluid called hybrid nanofluid. Hybrid nanofluids are prepared either by dispersing dissimilar nanoparticles as individual constituents or by dispersing nanocomposite particles in the base fluid. Hybrid nanofluids may possess better thermal network and rheological properties due to synergistic effect. Researchers, to adjudge the advantages, disadvantages and their suitability for diversified applications, are extensively investigating the behavior and properties of these hybrid nanofluids. This review summarizes the contemporary investigations on synthesis, thermo-physical properties, heat transfer characteristics, hydrodynamic behavior and fluid flow characteristics reported by researchers on different hybrid nanofluids. This review also outlines the applications and challenges associated with hybrid nanofluid and makes some suggestions for future scope of research in this area.
402 citations
TL;DR: In this paper, an emerging concept of hybrid nanofluid with a new improved model of its thermophysical properties is introduced in the present work, which has been employed for the enhancement of heat transfer rate.
Abstract: Abstract An emerging concept of hybrid nanofluid with a new improved model of its thermophysical properties are introduced in the present work. Hybrid nanofluid is an advanced type of conventional heat transfer fluids, which has been employed for the enhancement of heat transfer rate. Two distinct fluids, namely hybrid nanofluid (Cu−Al2O3/water)$({\\rm{Cu - A}}{{\\rm{l}}_{\\rm{2}}}{{\\rm{O}}_{\\rm{3}}}{\\rm{/water}})$ and nanofluid (Cu/water) are used to investigate the parametric features of the flow and heat transfer phenomena over a permeable stretching sheet in the presence of magnetic field. The effects of various physical parameters and effecting physical quantities of interest are analyzed. From this study it is observed that the heat transfer rate of hybrid nanofluid (Cu−Al2O3/water)$({\\rm{Cu - A}}{{\\rm{l}}_{\\rm{2}}}{{\\rm{O}}_{\\rm{3}}}{\\rm{/water}})$ is higher than that of Nanofluid (Cu/water) under magnetic field environment. More combinations of different nanocomposites can be tried so that the desired heat transfer rate can be achieved.
397 citations
Cites background from "Effects of Al2O3–Cu/water hybrid na..."
...Takabi and Shokouhmand [9] conveyed the effects of Al2O3 −Cu=water hybrid nanofluid on heat transfer and flow characteristics in turbulent regime....
[...]
TL;DR: In this paper, the authors seek the attention of young scholars and experts working in the field of heat transfer by discussing the applications and challenges of hybrid nanofluids with a concise discussion on its history, synthesis techniques, thermophysical properties, research gaps, future directions, current status, and the leading groups, organizations and countries around the world.
312 citations
TL;DR: A comprehensive literature on synthesis of hybrid nanoparticles, hybrid nanofluid and thermophysical properties of hybrid nano-fluids has been compiled and reviewed in this article, where the challenges and future trends in the application of hybrid Nanofluids in heat transfer applications are discussed.
300 citations
TL;DR: In this paper, the authors present a review of the research recent results concerning the thermo-physical properties (thermal conductivity, viscosity, density and specific heat) and the heat transfer and flow characteristics of hybrid nanofluids used in various heat exchangers.
285 citations
References
More filters
TL;DR: In this article, a general, numerical, marching procedure is presented for the calculation of the transport processes in three-dimensional flows characterised by the presence of one coordinate in which physical influences are exerted in only one direction.
5,946 citations
TL;DR: In this article, the authors considered seven slip mechanisms that can produce a relative velocity between the nanoparticles and the base fluid and concluded that only Brownian diffusion and thermophoresis are important slip mechanisms in nanofluids.
Abstract: Nanofluids are engineered colloids made of a base fluid and nanoparticles (1-100 nm) Nanofluids have higher thermal conductivity' and single-phase heat transfer coefficients than their base fluids In particular the heat transfer coefficient increases appear to go beyond the mere thermal-conductivity effect, and cannot be predicted by traditional pure-fluid correlations such as Dittus-Boelter's In the nanofluid literature this behavior is generally attributed to thermal dispersion and intensified turbulence, brought about by nanoparticle motion To test the validity of this assumption, we have considered seven slip mechanisms that can produce a relative velocity between the nanoparticles and the base fluid These are inertia, Brownian diffusion, thermophoresis, diffusioplwresis, Magnus effect, fluid drainage, and gravity We concluded that, of these seven, only Brownian diffusion and thermophoresis are important slip mechanisms in nanofluids Based on this finding, we developed a two-component four-equation nonhomogeneous equilibrium model for mass, momentum, and heat transport in nanofluids A nondimensional analysis of the equations suggests that energy transfer by nanoparticle dispersion is negligible, and thus cannot explain the abnormal heat transfer coefficient increases Furthermore, a comparison of the nanoparticle and turbulent eddy time and length scales clearly indicates that the nanoparticles move homogeneously with the fluid in the presence of turbulent eddies so an effect on turbulence intensity is also doubtful Thus, we propose an alternative explanation for the abnormal heat transfer coefficient increases: the nanofluid properties may vary significantly within the boundary layer because of the effect of the temperature gradient and thermophoresis For a heated fluid, these effects can result in a significant decrease of viscosity within the boundary layer, thus leading to heat transfer enhancement A correlation structure that captures these effects is proposed
5,329 citations
TL;DR: In this article, the authors used a Brookfield rotating viscometer to measure the viscosities of the dispersed fluids with γ-alumina (Al2O3) and titanium dioxide (TiO2) particles at a 10% volume concentration.
Abstract: Turbulent friction and heat transfer behaviors of dispersed fluids (i.e., uttrafine metallic oxide particles suspended in water) in a circular pipe were investigated experimentally. Viscosity measurements were also conducted using a Brookfield rotating viscometer. Two different metallic oxide particles, γ-alumina (Al2O3) and titanium dioxide (TiO2), with mean diameters of 13 and 27 nm, respectively, were used as suspended particles. The Reynolds and Prandtl numbers varied in the ranges l04-I05 and 6.5-12.3, respectively. The viscosities of the dispersed fluids with γ-Al2O3 and TiO2 particles at a 10% volume concentration were approximately 200 and 3 times greater than that of water, respectively. These viscosity results were significantly larger than the predictions from the classical theory of suspension rheology. Darcy friction factors for the dispersed fluids of the volume concentration ranging from 1% to 3% coincided well with Kays' correlation for turbulent flow of a single-phase fluid. The Nusselt n...
3,730 citations
TL;DR: In this paper, an expression for the viscosity of solutions and suspensions of finite concentration is derived by considering the effect of the addition of one solute-molecule to an existing solution, which is considered as a continuous medium.
Abstract: An expression for the viscosity of solutions and suspensions of finite concentration is derived by considering the effect of the addition of one solute‐molecule to an existing solution, which is considered as a continuous medium.
3,724 citations
TL;DR: In this paper, it was shown that a "nanofluid" consisting of copper nanometer-sized particles dispersed in ethylene glycol has a much higher effective thermal conductivity than either pure or pure glycol or even polyethylene glycol containing the same volume fraction of dispersed oxide nanoparticles.
Abstract: It is shown that a “nanofluid” consisting of copper nanometer-sized particles dispersed in ethylene glycol has a much higher effective thermal conductivity than either pure ethylene glycol or ethylene glycol containing the same volume fraction of dispersed oxide nanoparticles. The effective thermal conductivity of ethylene glycol is shown to be increased by up to 40% for a nanofluid consisting of ethylene glycol containing approximately 0.3 vol % Cu nanoparticles of mean diameter <10 nm. The results are anomalous based on previous theoretical calculations that had predicted a strong effect of particle shape on effective nanofluid thermal conductivity, but no effect of either particle size or particle thermal conductivity.
3,551 citations