Electrical characteristics and efficiency of single-layer organic light-emitting diodes
IBM1
TL;DR: In this article, the authors measured the electrical characteristics and the efficiencies of single-layer organic light-emitting diodes based on poly[2methoxy-5-(2-ethylhexoxy)-1,4-phenylene vinylene] (MEH-PPV), with Au anodes and Ca, Al, and Au cathodes.
Abstract: We have measured the electrical characteristics and the efficiencies of single-layer organic light-emitting diodes based on poly[2-methoxy-5-(2-ethylhexoxy)-1,4-phenylene vinylene] (MEH-PPV), with Au anodes and Ca, Al, and Au cathodes. We show that proper accounting of the built-in potential leads to a consistent description of the current-voltage data. For the case of Au and Al cathodes, the current under forward bias is dominated by holes injected from the anode and is space-charge limited with a field-dependent hole mobility. The Ca cathode is capable of injecting a space-charge-limited electron current.
Citations
More filters
TL;DR: It was found that films with finely distributed polymer/fulleride interpenetrating network exhibited improved solar cell conversion efficiency, and the results proved that polymer solar cells have a bright future.
Abstract: This paper describes synthesis and photovoltaic studies of a series of new semiconducting polymers with alternating thieno[3,4-b]thiophene and benzodithiophene units. The physical properties of these polymers were finely tuned to optimize their photovoltaic effect. The substitution of alkoxy side chains to the less electron-donating alkyl chains or introduction of electron-withdrawing fluorine into the polymer backbone reduced the HOMO energy levels of polymers. The structural modifications optimized polymers’ spectral coverage of absorption and their hole mobility, as well as miscibility with fulleride, and enhanced polymer solar cell performances. The open circuit voltage, Voc, for polymer solar cells was increased by adjusting polymer energy levels. It was found that films with finely distributed polymer/fulleride interpenetrating network exhibited improved solar cell conversion efficiency. Efficiency over 6% has been achieved in simple solar cells based on fluorinated PTB4/PC61BM films prepared from m...
1,366 citations
TL;DR: This work designed an 5-alkylthiophene-2-yl-substituted BDT monomer and synthesized two new PBDTTT-based polymers having either the thieno[3,4b], 4,7-dithiophene, 2,1,3-benzothiadiazole, and bithiazole properties, which showed promising photovoltaic properties.
Abstract: Polymer solar cells (PSCs) have attracted much attention because of their potential application in flexible, light-weight, and low-cost large-area devices through roll-to-roll printing. The bulk heterojunction PSCs showed advanced features in realizing high efficiencies and solution-processible devices. The active layer in this kind of device consists of an interpenetrating network formed by an electron-donor material blended with an electron-acceptor material. 3] Typically, conjugated polymers are used as electron donors and fullerene derivatives are used as the electron acceptors in the PSCs. Recently, power conversion efficiencies (PCEs) of 6–7% have been realized by using new conjugated polymer donors or new fullerene-derived acceptors. Short circuit current density (Jsc), open circuit voltage (Voc), and fill factors (FF) are key parameters for a PSC device, because the PCE of the device is proportional to the values of the three parameters. To broaden the response wavelength range of a PSC device by using conjugated side chains or narrowband-gap conjugated polymers is an effective way to realize high Jsc values. Conjugated polymers with lower HOMO levels are helpful in realizing high Voc and PCE values, as the Voc value of PSCs is directly proportional to the offset between the HOMO level of electron donor and the LUMO level of electron acceptor. PSiFDTBT, PFDTBT, and PCDTBT are three excellent examples for this concept. Consequently, by using conjugated polymers with lower HOMO levels and also narrow band gaps, high PCEs were realized in different families of conjugated polymers. Conjugated polymers based on benzo[1,2-b :4,5-b’]dithiophene (BDT) units have attracted interest as electron donors in the PSC field in recent years, since the report of Hou and Yang et al. on the synthesis and photovoltaic properties of a series of copolymers based on BDT. Many copolymers of BDT with different conjugated units, such as thieno[3,4b]thiophene (TT), 4,7-dithiophene-2-yl-2,1,3-benzothiadiazole (DTBT), N-alkylthieno[3,4-c]pyrrole-4,6-dione (TPD), and bithiazole, etc. were synthesized, and the copolymers showed promising photovoltaic properties. In these BDT-based polymers, the alternative copolymers of BDT and TT, namely PBDTTTs, are an important family of photovoltaic materials. For additional improvements in the photovoltaic performance of the PBDTTTs, structural modifications brought about by using different substituents on BDT, or the copolymerized moieties is of great importance. For example, Liang et al. introduced a fluorine atom into the TT unit of the PBDTTTs, and the HOMO level of the resulting polymer was successfully lowered by approximately 0.12 eV, and thus a higher Voc value was achieved, resulting in a great improvement of PCE. Hou et al. optimized PBDTTTs further by replacing the alkoxycarbonyl group on the TT unit with the alkylcarbonyl groups. The structural modification can also be carried out on the BDT units. In this work, we designed an 5-alkylthiophene-2-yl-substituted BDT monomer and synthesized two new PBDTTT-based polymers having either the thienylsubstituted BDT with alkoxycarbonyl-substituted thieno[3,4b]thiophene (TT-E) or the alkylcarbonyl-substituted thieno[3,4-b]thiophene (TT-C); that is PBDTTT-E-Tand PBDTTTC-T, respectively (Scheme 1). To fully investigate the effect of the thienyl-substituted BDTon the photovoltaic properties of the polymers, two corresponding PBDTTT polymers based on the alkoxy-substituted BDT (BDT-O), PBDTTT-E and PBDTTT-C (Scheme 1), were also prepared. The synthetic route of the thienyl-substituted BDT monomer (BDT-T) is shown in Scheme 1. The branched alkyl group 2-ethylhexyl was employed as the side chain on the thiophene to guarantee high solubility of the target polymers. The TT-E and TT-C monomers are commercially available. The polymers were prepared through a Stille coupling reaction between the bis(trimethyltin) BDT monomers (BDT-T and BDT-O) and the bromides (TT-E and TTC) as shown in Scheme 1. All the polymers are soluble in chloroform (CHCl3), chlorobenzene, and dichlorobenzene. Thermogravimetric analysis (TGA) measurements were employed to evaluate the thermal stability of the polymers. We found that the two-dimentional (2D) conjugated polymers based on alkylthienyl-substituted BDTs are much more stable than their analogues, the alkoxy-substituted BDTs. The TGA plots of these four polymers are shown in Figure 1. It can be seen that the decomposition temperatures [*] Dr. L. Huo, S. Zhang, F. Xu, Prof. J. Hou State Key Laboratory of Polymer Physics and Chemistry Beijing National Laboratory for Molecular Sciences Institute of Chemistry, Chinese Academy of Sciences Beijing 100190 (China) E-mail: hjhzlz@iccas.ac.cn
969 citations
TL;DR: A trialkylsilyl substituted 2D-conjugated polymer with the highest occupied molecular orbital level down-shifted by Si–C bond interaction is developed and indicates that the alkylsilyl substitution is an effective way in designing high performance conjugated polymer photovoltaic materials.
Abstract: Simutaneously high open circuit voltage and high short circuit current density is a big challenge for achieving high efficiency polymer solar cells due to the excitonic nature of organic semdonductors. Herein, we developed a trialkylsilyl substituted 2D-conjugated polymer with the highest occupied molecular orbital level down-shifted by Si–C bond interaction. The polymer solar cells obtained by pairing this polymer with a non-fullerene acceptor demonstrated a high power conversion efficiency of 11.41% with both high open circuit voltage of 0.94 V and high short circuit current density of 17.32 mA cm−2 benefitted from the complementary absorption of the donor and acceptor, and the high hole transfer efficiency from acceptor to donor although the highest occupied molecular orbital level difference between the donor and acceptor is only 0.11 eV. The results indicate that the alkylsilyl substitution is an effective way in designing high performance conjugated polymer photovoltaic materials. In organic photovoltaics, non-fullerene acceptors relax matching rules and allow for the development of new donor polymers. Here, Bin et al. design a donor polymer and obtain high photoconversion efficiencies despite the low energy offset for hole transfer between the acceptor and the donor.
896 citations
TL;DR: The results indicate that m-ITIC is a promising low bandgap n-OS for the application as an acceptor in PSCs, and the side-chain isomerization could be an easy and convenient way to further improve the photovoltaic performance of the donor and acceptor materials for high efficiency P SCs.
Abstract: Low bandgap n-type organic semiconductor (n-OS) ITIC has attracted great attention for the application as an acceptor with medium bandgap p-type conjugated polymer as donor in nonfullerene polymer solar cells (PSCs) because of its attractive photovoltaic performance. Here we report a modification on the molecular structure of ITIC by side-chain isomerization with meta-alkyl-phenyl substitution, m-ITIC, to further improve its photovoltaic performance. In a comparison with its isomeric counterpart ITIC with para-alkyl-phenyl substitution, m-ITIC shows a higher film absorption coefficient, a larger crystalline coherence, and higher electron mobility. These inherent advantages of m-ITIC resulted in a higher power conversion efficiency (PCE) of 11.77% for the nonfullerene PSCs with m-ITIC as acceptor and a medium bandgap polymer J61 as donor, which is significantly improved over that (10.57%) of the corresponding devices with ITIC as acceptor. To the best of our knowledge, the PCE of 11.77% is one of the highe...
806 citations
TL;DR: Recent progress is summarized in developing a new class of semiconducting polymers, which represents the first polymeric system to generate solar PCE greater than 7%.
Abstract: Solar cells based on the polymer−fullerene bulk heterojunction (BHJ) concept are an attractive class of low-cost solar energy harvesting devices. Because the power conversion efficiency (PCE) of these solar cells is still significantly lower than that of their inorganic counterparts, however, materials design and device engineering efforts are directed toward improving their output. A variety of factors limit the performance of BHJ solar cells, but the properties of the materials in the active layer are the primary determinant of their overall efficiency. The ideal polymer in a BHJ structure should exhibit the following set of physical properties: a broad absorption with high coefficient in the solar spectrum to efficiently harvest solar energy, a bicontinuous network with domain width within twice that of the exciton diffusion length, and high donor−acceptor interfacial area to favor exciton dissociation and efficient transport of separated charges to the respective electrodes. To facilitate exciton diss...
670 citations