Flexible, low-temperature, solution processed ZnO-based perovskite solid state solar cells
31 Oct 2013-Chemical Communications (The Royal Society of Chemistry)-Vol. 49, Iss: 94, pp 11089-11091
TL;DR: A ZNO compact layer formed by electrodeposition and ZnO nanorods grown by chemical bath deposition allow the processing of low-temperature, solution based and flexible solid state perovskite CH3NH3PbI3 solar cells.
About: This article is published in Chemical Communications.The article was published on 2013-10-31. It has received 534 citations till now. The article focuses on the topics: Chemical bath deposition & Perovskite (structure).
Citations
More filters
TL;DR: It is revealed that solution-processed organic-inorganic halide perovskites (CH3NH3PbX3), which demonstrated huge potential in photovoltaics, also have promising optical gain and may show electrically driven lasing.
Abstract: Low-temperature solution-processed materials that show optical gain and can be embedded into a wide range of cavity resonators are attractive for the realization of on-chip coherent light sources. Organic semiconductors and colloidal quantum dots are considered the main candidates for this application. However, stumbling blocks in organic lasing include intrinsic losses from bimolecular annihilation and the conflicting requirements of high charge carrier mobility and large stimulated emission; whereas challenges pertaining to Auger losses and charge transport in quantum dots still remain. Herein, we reveal that solution-processed organic-inorganic halide perovskites (CH 3 NH 3 PbX 3 where X = Cl, Br, I), which demonstrated huge potential in photovoltaics, also have promising optical gain. Their ultra-stable amplified spontaneous emission at strikingly low thresholds stems from their large absorption coefficients, ultralow bulk defect densities and slow Auger recombination. Straightforward visible spectral tunability (390-790 nm) is demonstrated. Importantly, in view of their balanced ambipolar charge transport characteristics, these materials may show electrically driven lasing. © 2014 Macmillan Publishers Limited.
2,691 citations
TL;DR: The use of a thin layer of zinc oxide nanoparticles as an electron-transport layer allows flexible perovskite solar cells to be fabricated with a power conversion efficiency as high as 15.7% as mentioned in this paper.
Abstract: The use of a thin layer of zinc oxide nanoparticles as an electron-transport layer allows flexible perovskite solar cells to be fabricated with a power conversion efficiency as high as 15.7%.
2,402 citations
TL;DR: In this paper, the defect properties of thin-film solar cells based on Methylammonium triiodideplumbate (CH3NH3PbI3) halide perovskites have been investigated.
Abstract: Thin-film solar cells based on Methylammonium triiodideplumbate (CH3NH3PbI3) halide perovskites have recently shown remarkable performance First-principle calculations show that CH3NH3PbI3 has unusual defect physics: (i) Different from common p-type thin-film solar cell absorbers, it exhibits flexible conductivity from good p-type, intrinsic to good n-type depending on the growth conditions; (ii) Dominant intrinsic defects create only shallow levels, which partially explain the long electron-hole diffusion length and high open-circuit voltage in solar cell The unusual defect properties can be attributed to the strong Pb lone-pair s orbital and I p orbital antibonding coupling and the high ionicity of CH3NH3PbI3
2,129 citations
TL;DR: A low-temperature processing technique is adopted to attain high-efficiency devices in both rigid and flexible substrates, using device structure substrate/ITO/PEDOT:PSS/CH(3)NH( 3)PbI(3-x)Cl(x)/PCBM/Al, where PEDOT?:PSS and PCBM are used as hole and electron transport layers, respectively.
Abstract: Perovskite compounds have attracted recently great attention in photovoltaic research. The devices are typically fabricated using condensed or mesoporous TiO2 as the electron transport layer and 2,2′7,7′-tetrakis-(N,N-dip-methoxyphenylamine)9,9′-spirobifluorene as the hole transport layer. However, the high-temperature processing (450 °C) requirement of the TiO2 layer could hinder the widespread adoption of the technology. In this report, we adopted a low-temperature processing technique to attain high-efficiency devices in both rigid and flexible substrates, using device structure substrate/ITO/PEDOT:PSS/CH3NH3PbI3–xClx/PCBM/Al, where PEDOT:PSS and PCBM are used as hole and electron transport layers, respectively. Mixed halide perovskite, CH3NH3PbI3–xClx, was used due to its long carrier lifetime and good electrical properties. All of these layers are solution-processed under 120 °C. Based on the proposed device structure, power conversion efficiency (PCE) of 11.5% is obtained in rigid substrates (glass/...
1,314 citations
Cites methods from "Flexible, low-temperature, solution..."
...processed perovskite solar cells using different transport layer processing.(21) 23...
[...]
TL;DR: In this review, basic fundamentals of perovskite materials including opto-electronic and dielectric properties are described to give a better understanding and insight into high-performing perovkite solar cells.
Abstract: Perovskite solar cells based on organometal halide light absorbers have been considered a promising photovoltaic technology due to their superb power conversion efficiency (PCE) along with very low material costs. Since the first report on a long-term durable solid-state perovskite solar cell with a PCE of 9.7% in 2012, a PCE as high as 19.3% was demonstrated in 2014, and a certified PCE of 17.9% was shown in 2014. Such a high photovoltaic performance is attributed to optically high absorption characteristics and balanced charge transport properties with long diffusion lengths. Nevertheless, there are lots of puzzles to unravel the basis for such high photovoltaic performances. The working principle of perovskite solar cells has not been well established by far, which is the most important thing for understanding perovksite solar cells. In this review, basic fundamentals of perovskite materials including opto-electronic and dielectric properties are described to give a better understanding and insight into high-performing perovskite solar cells. In addition, various fabrication techniques and device structures are described toward the further improvement of perovskite solar cells.
1,111 citations
References
More filters
TL;DR: Two organolead halide perovskite nanocrystals were found to efficiently sensitize TiO(2) for visible-light conversion in photoelectrochemical cells, which exhibit strong band-gap absorptions as semiconductors.
Abstract: Two organolead halide perovskite nanocrystals, CH3NH3PbBr3 and CH3NH3PbI3, were found to efficiently sensitize TiO2 for visible-light conversion in photoelectrochemical cells. When self-assembled on mesoporous TiO2 films, the nanocrystalline perovskites exhibit strong band-gap absorptions as semiconductors. The CH3NH3PbI3-based photocell with spectral sensitivity of up to 800 nm yielded a solar energy conversion efficiency of 3.8%. The CH3NH3PbBr3-based cell showed a high photovoltage of 0.96 V with an external quantum conversion efficiency of 65%.
16,634 citations
TL;DR: A sequential deposition method for the formation of the perovskite pigment within the porous metal oxide film that greatly increases the reproducibility of their performance and allows the fabrication of solid-state mesoscopic solar cells with unprecedented power conversion efficiencies and high stability.
Abstract: Following pioneering work, solution-processable organic-inorganic hybrid perovskites-such as CH3NH3PbX3 (X = Cl, Br, I)-have attracted attention as light-harvesting materials for mesoscopic solar cells. So far, the perovskite pigment has been deposited in a single step onto mesoporous metal oxide films using a mixture of PbX2 and CH3NH3X in a common solvent. However, the uncontrolled precipitation of the perovskite produces large morphological variations, resulting in a wide spread of photovoltaic performance in the resulting devices, which hampers the prospects for practical applications. Here we describe a sequential deposition method for the formation of the perovskite pigment within the porous metal oxide film. PbI2 is first introduced from solution into a nanoporous titanium dioxide film and subsequently transformed into the perovskite by exposing it to a solution of CH3NH3I. We find that the conversion occurs within the nanoporous host as soon as the two components come into contact, permitting much better control over the perovskite morphology than is possible with the previously employed route. Using this technique for the fabrication of solid-state mesoscopic solar cells greatly increases the reproducibility of their performance and allows us to achieve a power conversion efficiency of approximately 15 per cent (measured under standard AM1.5G test conditions on solar zenith angle, solar light intensity and cell temperature). This two-step method should provide new opportunities for the fabrication of solution-processed photovoltaic cells with unprecedented power conversion efficiencies and high stability equal to or even greater than those of today's best thin-film photovoltaic devices.
8,427 citations
TL;DR: The use of a solid hole conductor dramatically improved the device stability compared to (CH3NH3)PbI3 -sensitized liquid junction cells.
Abstract: We report on solid-state mesoscopic heterojunction solar cells employing nanoparticles (NPs) of methyl ammonium lead iodide (CH3NH3)PbI3 as light harvesters. The perovskite NPs were produced by reaction of methylammonium iodide with PbI2 and deposited onto a submicron-thick mesoscopic TiO2 film, whose pores were infiltrated with the hole-conductor spiro-MeOTAD. Illumination with standard AM-1.5 sunlight generated large photocurrents (JSC) exceeding 17 mA/cm2, an open circuit photovoltage (VOC) of 0.888 V and a fill factor (FF) of 0.62 yielding a power conversion efficiency (PCE) of 9.7%, the highest reported to date for such cells. Femto second laser studies combined with photo-induced absorption measurements showed charge separation to proceed via hole injection from the excited (CH3NH3)PbI3 NPs into the spiro-MeOTAD followed by electron transfer to the mesoscopic TiO2 film. The use of a solid hole conductor dramatically improved the device stability compared to (CH3NH3)PbI3 -sensitized liquid junction cells.
6,751 citations
TL;DR: Perovskite QD-sensitized 3.6 μm-thick TiO(2) film shows maximum external quantum efficiency (EQE) of 78.6% at 530 nm and solar-to-electrical conversion efficiency of 6.54% at AM 1.5G 1 sun intensity (100 mW cm(-2)), which is by far the highest efficiency among the reported inorganic quantum dot sensitizers.
Abstract: Highly efficient quantum-dot-sensitized solar cell is fabricated using ca. 2–3 nm sized perovskite (CH3NH3)PbI3 nanocrystal. Spin-coating of the equimolar mixture of CH3NH3I and PbI2 in γ-butyrolactone solution (perovskite precursor solution) leads to (CH3NH3)PbI3 quantum dots (QDs) on nanocrystalline TiO2 surface. By electrochemical junction with iodide/iodine based redox electrolyte, perovskite QD-sensitized 3.6 μm-thick TiO2 film shows maximum external quantum efficiency (EQE) of 78.6% at 530 nm and solar-to-electrical conversion efficiency of 6.54% at AM 1.5G 1 sun intensity (100 mW cm−2), which is by far the highest efficiency among the reported inorganic quantum dot sensitizers.
2,781 citations
TL;DR: In this paper, a layered sandwich-type architecture is proposed for next-generation dye-sensitized solar cells, which consists of a bicontinuous three-dimensional nanocomposite of mesoporous (mp)-TiO2,w ith CH 3NH3PbII3 perovskite as light harvester, as well as a polymeric hole conductor.
Abstract: Inorganic‐organic hybrid structures have become innovative alternatives for next-generation dye-sensitized solar cells, because they combine the advantages of both systems. Here, we introduce a layered sandwich-type architecture, the core of which comprises a bicontinuous three-dimensional nanocomposite of mesoporous (mp)-TiO2 ,w ith CH 3NH3PbI3 perovskite as light harvester, as well as a polymeric hole conductor. This platform creates new opportunities for the development of low-cost, solution-processed, high-efficiency solar cells. The use of a polymeric hole conductor, especially poly-triarylamine, substantially improves the open-circuit voltage V oc and fill factor of the cells. Solar cells based on these inorganic‐organic hybrids exhibit a short-circuit current density Jsc of 16.5 mA cm 22 , Voc of 0.997 V and fill factor of 0.727, yielding a power conversion efficiency of 12.0% under standard AM 1.5 conditions.
2,461 citations