Journal ArticleDOI
High-speed machining of aluminium alloy using vegetable oil based small quantity lubrication:
Balakrushna Guntreddi,Amitava Ghosh +1 more
- pp 095440542092978
Reads0
Chats0
TLDR
In an attempt to investigate the effectiveness of vegetable oil based small quantity lubrication in high-speed machining of aluminium, this paper found that its usefulness is more significant in an...Abstract:
In an attempt to investigate the effectiveness of vegetable oil based small quantity lubrication in high-speed machining of aluminium, this study finds that its usefulness is more significant in an...read more
Citations
More filters
Journal ArticleDOI
Resource saving by optimization and machining environments for sustainable manufacturing: A review and future prospects
TL;DR: The most important aspect of sustainability in manufacturing is the preservation of energy and natural resources as discussed by the authors , which can be achieved by increasing energy efficiency through low, clean, and renewable energy consumption.
Journal ArticleDOI
Dry Machining Performance of AA7075-T6 Alloy Using Uncoated Carbide and MT-CVD TiCN-Al2O3-Coated Carbide Inserts
TL;DR: In this article, the performance of AA7075 T6 alloy with uncoated and MT-CVD TiCN-Al2O3-coated carbide inserts is evaluated with regard to tangential cutting force, tool tip temperature and depth of flank wear.
Journal ArticleDOI
Anti-frictional role of diamond and graphite suspended bio-oil based nano-aerosols at sliding interface of Al-SiCp and WC-6Co
TL;DR: In this article, the authors investigated tribo-phenomena at sliding interface of Al2124-17SiCp disc and WC-6Co pin and explored suitability of nano-oil aerosols as lubricants.
Journal ArticleDOI
Experimental research on machinability characteristics of Al-9Si alloy: Effect of Sr and Mg additives
TL;DR: In this article , the effects of strontium (Sr) and magnesium (Mg) elements in certain rates added to Al-9Si alloy manufactured using permanent mold casting technique on the structural, mechanical, and machinability properties of these alloys were investigated.
References
More filters
Journal ArticleDOI
Machinability study of pure aluminium and Al–12% Si alloys against uncoated and coated carbide inserts
TL;DR: In this article, an investigation has been undertaken to study the compatibility of cutting materials in dry machining of aluminium and Al-Si alloys, and the results of turning test, SEM pictures and chip morphology investigation of the cutting tool after machining clearly reveal the inefficiency of TiC, TiN, TiB2, Al2O3, and AlON.
Journal ArticleDOI
A SEM and EDS insight into the BUL and BUE differences in the turning processes of AA2024 Al–Cu alloy
TL;DR: In this article, the authors report on the results of a study using the SEM and EDS of the microstructural features of BUL and BUE formed over TiN turning inserts in machining of an Al-Cu alloy.
Journal ArticleDOI
Microscopic observations of adiabatic shear bands in three different steels
K. Cho,Y. C. Chi,J. Duffy +2 more
TL;DR: In this article, microscopic observations were made of the shear band material in three different steels: (1) an AISI 1018 cold-rolled steel (CRS), (2) a structural steel (HY-100), and (3) a vacuum arc remelted (VAR) steel tempered to either of two hardnesses, RHC 44 or 55.
Journal ArticleDOI
Analyzing the performance of diamond-coated micro end mills.
Christopher D. Torres,Patrick J. Heaney,Anirudha V. Sumant,M. A. Hamilton,Robert W. Carpick,Frank E. Pfefferkorn +5 more
TL;DR: In this paper, a method was presented to improve the tool life and cutting performance of 300mm diameter tungsten carbide (WC) micro end mills by applying thin (50%). Reduction of the cutting forces is attributed to the low friction and adhesion of the diamond coating.
Journal ArticleDOI
A study of plastic strain and plastic strain rate in machining of steel AISI 1045 using FEM analysis
João Paulo Davim,C. Maranhão +1 more
TL;DR: In this paper, the effect of high speed machining (HSM) in the plastic strain and plastic strain rate when cutting steel AISI 1045 was observed, and it can be concluded that both the PL strain and PL strain rate can be predicted with good precision when machining with the FEM model.