Interferometric Fiber Optic Sensors
23 Feb 2012-Sensors (Multidisciplinary Digital Publishing Institute (MDPI))-Vol. 12, Iss: 3, pp 2467-2486
TL;DR: Each type of interferometric sensor is reviewed in terms of operating principles, fabrication methods, and application fields and some specific examples of recently reported interferometeric sensor technologies are presented in detail to show their large potential in practical applications.
Abstract: Fiber optic interferometers to sense various physical parameters including temperature, strain, pressure, and refractive index have been widely investigated. They can be categorized into four types: Fabry-Perot, Mach-Zehnder, Michelson, and Sagnac. In this paper, each type of interferometric sensor is reviewed in terms of operating principles, fabrication methods, and application fields. Some specific examples of recently reported interferometeric sensor technologies are presented in detail to show their large potential in practical applications. Some of the simple to fabricate but exceedingly effective Fabry-Perot interferometers, implemented in both extrinsic and intrinsic structures, are discussed. Also, a wide variety of Mach-Zehnder and Michelson interferometric sensors based on photonic crystal fibers are introduced along with their remarkable sensing performances. Finally, the simultaneous multi-parameter sensing capability of a pair of long period fiber grating (LPG) is presented in two types of structures; one is the Mach-Zehnder interferometer formed in a double cladding fiber and the other is the highly sensitive Sagnac interferometer cascaded with an LPG pair.
Citations
More filters
TL;DR: A temperature sensor based on an asymmetric two-hole fiber (ATHF) using a Sagnac interferometer (SI) configuration with a linear response and the use of bigger holes which can facilitate the insertion of several materials and improve the sensitivity of the sensor for different applications is reported.
Abstract: We report in this paper a temperature sensor based on an asymmetric two-hole fiber (ATHF) using a Sagnac interferometer (SI) configuration. The operation principle is based on the birefringence change induced by the temperature difference between the air holes and the silica fiber. As a result, the transmitted spectrum of the SI exhibits a sinusoidal profile which is shifted when the temperature is increased. A linear wavelength shift as a function of temperature is observed, and a sensitivity of 2.22 nm/°C was achieved using a 2 m long asymmetric THF, which is in the same order as those previously reported using similar microstructured fibers. The advantage of this system is a linear response, the use of a microstructured fiber with a simpler transverse geometry, and the use of bigger holes which can facilitate the insertion of several materials and improve the sensitivity of the sensor for different applications.
13 citations
TL;DR: The proposed biocompatible fiber-optic pH sensor based on a unique double-pass Mach–Zehnder interferometer has been successfully applied in monitoring the media pH in cell culture experiments to investigate the relationship between pH and cancer cell growth.
Abstract: A biocompatible fiber-optic pH sensor based on a unique double-pass Mach-Zehnder interferometer is proposed. pH responsive poly(2-hydroxyethyl methacrylate-co-2-(dimethylamino)ethyl methacrylate) hydro- gel coating on the fiber swells/deswells in response to local pH, leading to refractive index changes that manifest as shifting of interference dips in the optical spectrum. The pH sensor is tested in spiked phosphate buffer saline and demonstrates high sensitivity of 1.71 nm∕pH, pH 0.004 limit of detection with good responsiveness, repeat- ability, and stability. The proposed sensor has been successfully applied in monitoring the media pH in cell culture experiments to investigate the relationship between pH and cancer cell growth. © 2014 Society of Photo- Optical Instrumentation Engineers (SPIE) (DOI: 10.1117/1.JBO.19.4.047002)
13 citations
Cites background from "Interferometric Fiber Optic Sensors..."
...range of applications and are touted to give remarkable performance in terms of sensitivity, accuracy, and dynamic range.(6) In...
[...]
TL;DR: A novel optical fiber extrinsic Fabry–Perot interferometer (EFPI) for probing pressure changes with subpascal (~0.1 Pa, $\sim 1.45\times 10^{-5}$ psi) resolution" has the potential to find a wide range of applications that require precise instrumentation.
Abstract: This article reports a novel optical fiber extrinsic Fabry–Perot interferometer (EFPI) for probing pressure changes with subpascal (~0.1 Pa, $\sim 1.45\times 10^{-5}$ psi) resolution. The principal idea of the sensor is to employ a traditional C-shaped Bourdon tube as a mechanical transducer that is coupled to a highly sensitive EFPI device. The cavity of the EFPI device is formed between a gold-coated mirror, mounted to a concave section of the Bourdon tube, and the endface of an optical fiber mounted at the base section of the Bourdon tube. Based on this design, the pressure-induced deflections of the Bourdon tube are directly correlated with the changes in cavity length of the EFPI, which can be determined by analyzing the interference signals. An experiment based on probing hydrostatic pressure changes induced by the addition of single water droplets to a test chamber was performed to quantify the measurement resolution of the proposed sensor because an apparatus for producing exceedingly small, stable, and reproducible pressure changes does not exist. Compared with conventional optical fiber pressure sensors, the proposed pressure sensor requires a simple fabrication process and can be used to measure pressure changes with high sensitivity ( $\sim 23.5~\mu \text{m}$ /kPa, cavity length change/pressure change). Moreover, the sensitivity and resolution of the pressure sensor can be flexibly adjusted using Bourdon tubes designed for different dynamic ranges (e.g., 0–70 MPa, 0–10152 psi). It is believed that the proposed novel pressure sensor has the potential to find a wide range of applications that require precise instrumentation.
13 citations
TL;DR: In this paper, a fiber optic Fabry-Perot (FP) interferometer with an open air cavity fabricated using a one-step mechanical sawing technique is presented.
Abstract: We have demonstrated a refractive index sensor based on a fiber optic Fabry–Perot (FP) interferometer with an open air cavity fabricated using a one-step mechanical sawing technique. The sensor head consists of a short FP cavity near the fiber patch cord tip, which was assembled by joining a ceramic ferrule and a single-mode fiber together. Owing to the open air cavity in the sensor head, various liquid samples with different refractive index can fill in-line air cavity, which makes the device usable as a refractometer. Moreover, due to the sensor head encircled with the robust ceramic ferrule, the device is attractive for sensing measurement in harsh environments. The sensor was tested in different refractive index solutions. The experimental result shows that the attenuation peak wavelength of the sensor is shifted toward a shorter wavelength with increasing refractive index, and the refractive index sensitivity is ∼92.5 nm/refractive index unit (RIU) and 73.75 dB/RIU . The proposed sensor can be used as an in-line refractometer for many potential applications in the sensing field.
12 citations
Cites background from "Interferometric Fiber Optic Sensors..."
...Optical fiber sensors have been intensively developed because of their many advantages, such as their compact and lightweight structures and resistance to electromagnetic interference and corrosion.(1,2) These fiber sensors are particularly attractive for applications involving various environments and can be used to monitor physical quantities such as temperature,(3,4) strain,(4,5) pressure,(6) displacement,(7) and reflective indices....
[...]
TL;DR: The paper deals with the overview of fiber optic methods suitable for temperature measurement and monitoring and evaluates the current research of temperature measurements in the interval from temperature close to 0 up to 1000°C.
Abstract: The paper deals with the overview of fiber optic methods suitable for temperature measurement and monitoring. The aim is to evaluate the current research of temperature measurements in the interval from temperature close to 0 up to 1000°C. Since the measuring chain is a functional combination of optical methods, optical fiber properties, and other photonic elements together with control electronic circuits, it is necessary to find a suitable compromise between the chosen measurement method, measuring range, accuracy, and resolution. Optical fiber sensors can be used in cases where standard electrical measurement methods cannot be used. These may be areas with high electrical and magnetic interference or critical areas. Therefore, there is intensive development of optical and fiber optic methods based on blackbody and greybody radiation, luminescence, fiber Bragg gratings (FBGs), and interferometers.
12 citations
Cites background from "Interferometric Fiber Optic Sensors..."
...[30] where the possibilities and uses of different types of fiber optic sensors were summarized....
[...]
References
More filters
21 Dec 2017
TL;DR: In this paper, the authors present a comprehensive and engaging introduction to optics for intermediate and upper level undergraduate physics and engineering students, which allows instructors to select specialized content to suit individual curricular needs and goals.
Abstract: Introduction to Optics is now available in a re-issued edition from Cambridge University Press. Designed to offer a comprehensive and engaging introduction to intermediate and upper level undergraduate physics and engineering students, this text also allows instructors to select specialized content to suit individual curricular needs and goals. Specific features of the text, in terms of coverage beyond traditional areas, include extensive use of matrices in dealing with ray tracing, polarization, and multiple thin-film interference; three chapters devoted to lasers; a separate chapter on the optics of the eye; and individual chapters on holography, coherence, fiber optics, interferometry, Fourier optics, nonlinear optics, and Fresnel equations.
927 citations
TL;DR: A detailed mechanism of the surface plasmon resonance (SPR) technique for sensing purposes has been discussed in this paper, where different new techniques and models in this area that have been introduced are discussed in quite a detail.
Abstract: Since the introduction of optical fiber technology in the field of sensor based on the technique of surface plasmon resonance (SPR), fiber-optic SPR sensors have witnessed a lot of advancements. This paper reports on the past, present, and future scope of fiber-optic SPR sensors in the field of sensing of different chemical, physical, and biochemical parameters. A detailed mechanism of the SPR technique for sensing purposes has been discussed. Different new techniques and models in this area that have been introduced are discussed in quite a detail. We have tried to put the different advancements in the order of their chronological evolution. The content of the review article may be of great importance for the research community who are to take the field of fiber-optic SPR sensors as its research endeavors.
824 citations
TL;DR: In this paper, an approach to achieve simultaneous measurement of refractive index and temperature is proposed by using a Mach-Zehnder interferometer realized on tapered single-mode optical fiber.
Abstract: An approach to achieve simultaneous measurement of refractive index and temperature is proposed by using a Mach–Zehnder interferometer realized on tapered single-mode optical fiber. The attenuation peak wavelength of the interference with specific order in the transmission spectrum shifts with changes in the environmental refractive index and temperature. By utilizing S-band and C/L-band light sources, simultaneous discrimination of refractive index and temperature with the tapered fiber Mach–Zehnder interferometer is demonstrated with the corresponding sensitivities of −23.188 nm/RIU (refractive index unit) and 0.071 nm/ °C, and −26.087 nm/RIU (blueshift) and 0.077 nm/°C (redshift) for the interference orders of 169 and 144, respectively.
551 citations
"Interferometric Fiber Optic Sensors..." refers background in this paper
...By tapering a fiber at two points along the fiber, we can form an effective in-line MZI as shown in Figure 7(f) [55,56]....
[...]
TL;DR: In this article, a fiber-based Fabry-Perot cavity with CO2 laser-machined mirrors was realized, which combines very small size, high finesse, small waist and mode volume, and good mode matching between the fiber and cavity modes.
Abstract: We have realized a fiber-based Fabry-Perot cavity with CO2 laser-machined mirrors. It combines very small size, high finesse F>=130000, small waist and mode volume, and good mode matching between the fiber and cavity modes. This combination of features is a major advance for cavity quantum electrodynamics (CQED), as shown in recent CQED experiments with Bose-Einstein condensates enabled by this cavity [Y. Colombe et al., Nature 450, 272 (2007)]. It should also be suitable for a wide range of other applications, including coupling to solid-state emitters, gas detection at the single-particle level, fiber-coupled single-photon sources and high-resolution optical filters with large stopband.
418 citations
"Interferometric Fiber Optic Sensors..." refers background in this paper
...Since it can utilize high reflecting mirrors, the extrinsic structure is useful to obtain a high finesse interference signal [23]....
[...]
TL;DR: As potential applications of the all-PCF interferometer, strain sensing is experimentally demonstrated and ultra-high temperature sensing is proposed.
Abstract: We propose simple and compact methods for implementing all-fiber interferometers. The interference between the core and the cladding modes of a photonic crystal fiber (PCF) is utilized. To excite the cladding modes from the fundamental core mode of a PCF, a coupling point or region is formed by using two methods. One is fusion splicing two pieces of a PCF with a small lateral offset, and the other is partially collapsing the air-holes in a single piece of PCF. By making another coupling point at a different location along the fiber, the proposed all-PCF interferometer is implemented. The spectral response of the interferometer is investigated mainly in terms of its wavelength spectrum. The spatial frequency of the spectrum was proportional to the physical length of the interferometer and the difference between the modal group indices of involved waveguide modes. For the splicing type interferometer, only a single spatial frequency component was dominantly observed, while the collapsing type was associated with several components at a time. By analyzing the spatial frequency spectrum of the wavelength spectrum, the modal group index differences of the PCF were obtained from 2.83×10-3 to 4.65 ×10-3 . As potential applications of the all-PCF interferometer, strain sensing is experimentally demonstrated and ultra-high temperature sensing is proposed.
418 citations
"Interferometric Fiber Optic Sensors..." refers background or methods in this paper
...However, in this case, coupling to several cladding modes was observed and controlling the number of involved modes was not so simple [51]....
[...]
...Even with PCF, an MZI can be formed by simply fusion-splicing a piece of PCF between fibers with a small intentional deviation [51]....
[...]
...In reference [51], as low as 2 dB splicing loss was achieved by making the mode coupling to dominantly one cladding mode of the PCF....
[...]