Investigation on Convective Heat Transfer and Flow Features of Nanofluids
01 Feb 2003-Journal of Heat Transfer-transactions of The Asme (American Society of Mechanical Engineers)-Vol. 125, Iss: 1, pp 151-155
TL;DR: In this article, an innovative new class of heat transfer fluids can be engineered by suspending metallic nanoparticles in conventional heat-transfer fluids, which are expected to exhibit high thermal conductivities compared to those of currently used heat transfer fluid, and they represent the best hope for enhancing heat transfer.
Abstract: Low thermal conductivity is a primary limitation in the development of energy-efficient heat transfer fluids that are required in many industrial applications. In this paper we propose that an innovative new class of heat transfer fluids can be engineered by suspending metallic nanoparticles in conventional heat transfer fluids. The resulting {open_quotes}nanofluids{close_quotes} are expected to exhibit high thermal conductivities compared to those of currently used heat transfer fluids, and they represent the best hope for enhancement of heat transfer. The results of a theoretical study of the thermal conductivity of nanofluids with copper nanophase materials are presented, the potential benefits of the fluids are estimated, and it is shown that one of the benefits of nanofluids will be dramatic reductions in heat exchanger pumping power.
Citations
More filters
TL;DR: In this article, a double pipe heat exchanger with and without helical coil inserts was studied experimentally, and the measured values of heat transfer coefficient and friction factor were compared with the published literature.
151 citations
TL;DR: A thermal and flow analysis of a fin shaped microchannel heat sink (MCHS) cooled by different nanofluids (Cu and Al2O3 in water) based on the least square method is presented in this article.
Abstract: This work presents a thermal and flow analysis of a fin shaped microchannel heat sink (MCHS) cooled by different nanofluids (Cu and Al2O3 in water) based on “saturated porous medium” and least square method then results are compared with numerical procedure. The Forchheimer–Brinkman-extended Darcy equation is used to describe the fluid flow and the two-equation model with thermal dispersion is utilized for heat transfer. The effect of nanoparticle size and volume fraction, volume flow rate, inertial force parameter and channel width investigated on total thermal resistance, friction factor and Nusselt number. The effective thermal conductivity and viscosity of nanofluid are calculated by KKL correlation. Central composite design (CCD) is applied to obtain the desirability of the optimum value of the nanofluid flow characteristics. Results show that Cu–water nanofluid is more lucrative thermally versus Al2O3–water nanofluid. It is found that total thermal resistance, friction factor and Nusselt number are not sensitive to inertial effect while they change significantly due to other parameters such as nanoparticle size and volume fraction, volume flow rate and channel width. We obtained that Nusselt number enhancement has direct relationship with inertial force parameter and volume flow rate.
151 citations
TL;DR: In this article, aqueous and ethylene glycol-based spherical titania nanofluids were used for forced convective heat transfer and they showed a higher effective thermal conductivity than that predicted by the conventional theories.
150 citations
TL;DR: In this article, a new correlation was developed for laminar flow in helically coiled tubes, which can predict the experimental heat transfer data very well, and the Seban and McLaughlin correlation can accurately predict the thermal behavior of water and nanofluids when nanof-luid properties are taken into account.
150 citations
TL;DR: In this article, the formation and dissociation of HFC134a (CH2FCF3) hydrate were studied in nano-copper suspensions of different mass fractions.
150 citations
References
More filters
Book•
01 Jan 1985
TL;DR: In this article, the physical concepts and methodologies of heat and mass transfer are explained for advanced undergraduate engineering majors, using a systematic method for problem solving and discusses the relationship of heat transfer to many important practical applications through examples and problems.
Abstract: This book, designed for advanced undergraduate engineering majors, explains the physical concepts and methodologies of heat and mass transfer. It uses a systematic method for problem solving and discusses the relationship of heat and mass transfer to many important practical applications through examples and problems. A and significant contribution is the extensive use of the First Law of thermodynamics.
4,113 citations
TL;DR: In this article, the authors used a Brookfield rotating viscometer to measure the viscosities of the dispersed fluids with γ-alumina (Al2O3) and titanium dioxide (TiO2) particles at a 10% volume concentration.
Abstract: Turbulent friction and heat transfer behaviors of dispersed fluids (i.e., uttrafine metallic oxide particles suspended in water) in a circular pipe were investigated experimentally. Viscosity measurements were also conducted using a Brookfield rotating viscometer. Two different metallic oxide particles, γ-alumina (Al2O3) and titanium dioxide (TiO2), with mean diameters of 13 and 27 nm, respectively, were used as suspended particles. The Reynolds and Prandtl numbers varied in the ranges l04-I05 and 6.5-12.3, respectively. The viscosities of the dispersed fluids with γ-Al2O3 and TiO2 particles at a 10% volume concentration were approximately 200 and 3 times greater than that of water, respectively. These viscosity results were significantly larger than the predictions from the classical theory of suspension rheology. Darcy friction factors for the dispersed fluids of the volume concentration ranging from 1% to 3% coincided well with Kays' correlation for turbulent flow of a single-phase fluid. The Nusselt n...
3,730 citations
3,019 citations
"Investigation on Convective Heat Tr..." refers background in this paper
...Hamilton and Crasser (1962) have developed a more elaborate model for the effective thermal conductivity of twocomponent mixtures as a function of the conductivity of the pure materials, the composition of the mixture, and the shape of the dispersed particles....
[...]
TL;DR: In this paper, a transient hot-wire method was used to measure the thermal conductivity of a small amount of nanoparticles and the experimental results showed that these nanoparticles have substantially higher thermal conductivities than the same liquids without nanoparticles.
Abstract: Oxide nanofluids were produced and their thermal conductivities were measured by a transient hot-wire method. The experimental results show that these nanofluids, containing a small amount of nanoparticles, have substantially higher thermal conductivities than the same liquids without nanoparticles. Comparisons between experiments and the Hamilton and Crosser model show that the model can predict the thermal conductivity of nanofluids containing large agglomerated Al{sub 2}O{sub 3} particles. However, the model appears to be inadequate for nanofluids containing CuO particles. This suggests that not only particle shape but size is considered to be dominant in enhancing the thermal conductivity of nanofluids.
2,811 citations
TL;DR: In this article, the authors proposed two different approaches for deriving heat transfer correlation of the nanofluid, and investigated the mechanism of heat transfer enhancement of the nano-fluid.
2,355 citations