Mechanical behavior of additive manufactured, powder-bed laser-fused materials
10 Jan 2016-Materials Science and Engineering A-structural Materials Properties Microstructure and Processing (Elsevier)-Vol. 651, Iss: 651, pp 198-213
TL;DR: In this paper, the effects of fabrication orientation, surface polishing, and hot isostatic pressing upon mechanical behavior of four metallic alloys fabricated with layered, laser-heated methods of additive manufacturing (AM) was compared to that of similar alloys produced with conventional methods (wrought and machined).
Abstract: Mechanical behavior of four metallic alloys fabricated with layered, laser-heated methods of additive manufacturing (AM) was compared to that of similar alloys produced with conventional methods (wrought and machined). AM materials were produced by a leading commercial service provider, as opposed to incorporating material specimens produced by unique or specially-adapted equipment. The elastic moduli were measured in flexure, stress–strain characteristics were measured in tensile deformation, and fatigue strengths were measured in fully reversed bending. The effects of fabrication orientation, surface polishing, and hot isostatic pressing upon mechanical behavior were studied. The fatigue strengths exhibited by SLM AlSi10Mg and DMLS Ti6Al4V in the as-fabricated condition proved to be significantly inferior to that of conventional material. These lower fatigue strengths are a consequence of multiple fatigue cracks initiating at surface defects, internal voids and microcracks, and growing simultaneously during cyclic loading. Measured fatigue strengths of DMLS 316L and 17-4PH approached those of corresponding wrought materials when subjected to principal stresses aligned with the build planes. When cyclic stresses were applied across the build planes of the DMLS stainless steels, fatigue fractures often developed prematurely by separation of material. Post-processing the DMLS Ti6Al4V and SS316L with hot isostatic pressure elevated the fatigue strength significantly. Measurements of surface roughness with an optical profilometer, examinations of the material microstructures, and fractography contribute to an understanding of the mechanical behavior of the additive materials.
Citations
More filters
TL;DR: A review of the emerging research on additive manufacturing of metallic materials is provided in this article, which provides a comprehensive overview of the physical processes and the underlying science of metallurgical structure and properties of the deposited parts.
4,192 citations
TL;DR: The potential of additive manufacturing to create alloys with unique microstructures and high performance for structural applications is demonstrated, with austenitic 316L stainless steels additively manufactured via a laser powder-bed-fusion technique exhibiting a combination of yield strength and tensile ductility that surpasses that of conventional 316L steels.
Abstract: Many traditional approaches for strengthening steels typically come at the expense of useful ductility, a dilemma known as strength-ductility trade-off. New metallurgical processing might offer the possibility of overcoming this. Here we report that austenitic 316L stainless steels additively manufactured via a laser powder-bed-fusion technique exhibit a combination of yield strength and tensile ductility that surpasses that of conventional 316L steels. High strength is attributed to solidification-enabled cellular structures, low-angle grain boundaries, and dislocations formed during manufacturing, while high uniform elongation correlates to a steady and progressive work-hardening mechanism regulated by a hierarchically heterogeneous microstructure, with length scales spanning nearly six orders of magnitude. In addition, solute segregation along cellular walls and low-angle grain boundaries can enhance dislocation pinning and promote twinning. This work demonstrates the potential of additive manufacturing to create alloys with unique microstructures and high performance for structural applications.
1,385 citations
TL;DR: In this paper, the recent progress on Ti6Al4V fabricated by three mostly developed additive manufacturing techniques-directed energy deposition (DED), selective laser melting (SLM) and electron beam melting (EBM)-is thoroughly investigated and compared.
1,248 citations
TL;DR: A comprehensive understanding of the interrelation between the various aspects of the subject, as this is essential to demonstrate credibility for industrial needs, is presented in this paper, which highlights some key topics requiring attention for further progression.
761 citations
TL;DR: In this paper, microstructure, defect formation and mechanical properties of AISI 316L components are investigated according to the process parameters used for their fabrication, and a first experimental campaign establishes process parameters guaranteeing a density greater than 98% Samples for microstructural and mechanical characterization are then produced based on these results, varying laser power from 100 W to 150 W, hatch space from 005 mm to 007 mm and orientation from 45° to 90°.
612 citations
References
More filters
TL;DR: Additive manufacturing implies layer by layer shaping and consolidation of powder feedstock to arbitrary configurations, normally using a computer controlled laser as discussed by the authors, which is based on a novel materials incremental manufacturing philosophy.
Abstract: Unlike conventional materials removal methods, additive manufacturing (AM) is based on a novel materials incremental manufacturing philosophy. Additive manufacturing implies layer by layer shaping and consolidation of powder feedstock to arbitrary configurations, normally using a computer controlled laser. The current development focus of AM is to produce complex shaped functional metallic components, including metals, alloys and metal matrix composites (MMCs), to meet demanding requirements from aerospace, defence, automotive and biomedical industries. Laser sintering (LS), laser melting (LM) and laser metal deposition (LMD) are presently regarded as the three most versatile AM processes. Laser based AM processes generally have a complex non-equilibrium physical and chemical metallurgical nature, which is material and process dependent. The influence of material characteristics and processing conditions on metallurgical mechanisms and resultant microstructural and mechanical properties of AM proc...
2,402 citations
TL;DR: In this article, the development of the microstructure of the Ti-6Al-4V alloy processed by selective laser melting (SLM) was studied by light optical microscopy.
2,201 citations
TL;DR: In this paper, the effect of several heat treatments on the microstructure and mechanical properties of Ti6Al4V processed by Selective Laser Melting (SLM) is studied.
1,320 citations
TL;DR: In this article, the authors describe which types of laser-induced consolidation can be applied to what type of material, and demonstrate that although SLS/SLM can process polymers, metals, ceramics and composites, quite some limitations and problems cause the palette of applicable materials still to be limited.
1,241 citations
TL;DR: In this article, the microstructure-defect-property relationship under cyclic loading for a TiAl6V4 alloy processed by selective laser melting is investigated. And the results show that the micron sized pores mainly affect fatigue strength, while residual stresses have a strong impact on fatigue crack growth.
1,079 citations