Mechanical Properties of Polymers and Composites

Introduction To Composite Materials

Abstract: The combination of materials to form a new material system with enhanced material properties is a well documented historical fact. For example, the ancient Jewish workers during their tenure under the Pharaohs used chopped straws in bricks as a means of enhancing their structural integrity. The Japanese Samurai warriors were known to use laminated metals in the forging of their swords to obtain desirable material properties. Even certain artisans from the Mediterranean and Far East used a form of composite technology in molding art works which were fabricated by layering cut paper in various sizes for producing desired shapes and contours.

Mechanical properties of nylon 6-clay hybrid

Abstract: Various nylon 6-clay hybrids, such as molecular composites of nylon 6 and silicate layers of montmorillonite and saponite, NCH's and NCHP's, respectively, have been synthesized. To estimate the mechanical properties of these hybrids, tensile, flexural, impact, and heat distortion tests were carried out. NCH was found superior in strength and modulus and comparable in impact strength to nylon 6. The heat distortion temperature (HDT) of NCH (montmorillonite: 4.7 wt. %) was 152 °C, which was 87 °C higher than that of nylon 6. In NCHP, saponite had a smaller effect on the increase of these mechanical properties. The modulus and HDT of NCH and NCHP increased with an increase in the amount of clay minerals. It was found that these properties were well described by the contribution of the constrained region calculated from the storage and loss modulus at the glass transition temperature. According to the mixing law on elastic modulus, the following expression was obtained between the modulus E at 120 °C and the fraction of the constrained region C, En = Ecn = C, where the values of n and Ec (modulus of the constrained region) were 0.685 and 1.02 GPa, respectively.

Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate–polymer composites

Abstract: There have been a number of review papers on layered silicate and carbon nanotube reinforced polymer nanocomposites, in which the fillers have high aspect ratios. Particulate–polymer nanocomposites containing fillers with small aspect ratios are also an important class of polymer composites. However, they have been apparently overlooked. Thus, in this paper, detailed discussions on the effects of particle size, particle/matrix interface adhesion and particle loading on the stiffness, strength and toughness of such particulate–polymer composites are reviewed. To develop high performance particulate composites, it is necessary to have some basic understanding of the stiffening, strengthening and toughening mechanisms of these composites. A critical evaluation of published experimental results in comparison with theoretical models is given.

Pretreatments of Natural Fibers and their Application as Reinforcing Material in Polymer Composites—A Review

Abstract: In recent years, natural fibers reinforced composites have received much attention because of their lightweight, nonabrasive, combustible, nontoxic, low cost and biodegradable properties. Among the various natural fibers; flax, bamboo, sisal, hemp, ramie, jute, and wood fibers are of particular interest. A lot of research work has been performed all over the world on the use of natural fibers as a reinforcing material for the preparation of various types of composites. However, lack of good interfacial adhesion, low melting point, and poor resistance towards moisture make the use of natural fiber reinforced composites less attractive. Pretreatments of the natural fiber can clean the fiber surface, chemically modify the surface, stop the moisture absorption process, and increase the surface roughness. Among the various pretreatment techniques, graft copolymerization and plasma treatment are the best methods for surface modification of natural fibers. Graft copolymers of natural fibers with vinyl monomers provide better adhesion between matrix and fiber. In the present article, the use of pretreated natural fibers in polymer matrix-based composites has been reviewed. Effect of surface modification of natural fibers on the properties of fibers and fiber reinforced polymer composites has also been discussed. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers

Sisal fibre and its composites: a review of recent developments

Abstract: Sisal fibre is a promising reinforcement for use in composites on account of its low cost, low density, high specific strength and modulus, no health risk, easy availability in some countries and renewability. In recent years, there has been an increasing interest in finding new applications for sisal-fibre-reinforced composites that are traditionally used for making ropes, mats, carpets, fancy articles and others. This review presents a summary of recent developments of sisal fibre and its composites. The properties of sisal fibre itself, interface between sisal fibre and matrix, properties of sisal-fibre-reinforced composites and their hybrid composites have been reviewed. Suggestions for future work are also given.