Millimeter-Wave Cellular Wireless Networks: Potentials and Challenges
05 Feb 2014-Vol. 102, Iss: 3, pp 366-385
TL;DR: Measurements and capacity studies are surveyed to assess mmW technology with a focus on small cell deployments in urban environments and it is shown that mmW systems can offer more than an order of magnitude increase in capacity over current state-of-the-art 4G cellular networks at current cell densities.
Abstract: Millimeter-wave (mmW) frequencies between 30 and 300 GHz are a new frontier for cellular communication that offers the promise of orders of magnitude greater bandwidths combined with further gains via beamforming and spatial multiplexing from multielement antenna arrays. This paper surveys measurements and capacity studies to assess this technology with a focus on small cell deployments in urban environments. The conclusions are extremely encouraging; measurements in New York City at 28 and 73 GHz demonstrate that, even in an urban canyon environment, significant non-line-of-sight (NLOS) outdoor, street-level coverage is possible up to approximately 200 m from a potential low-power microcell or picocell base station. In addition, based on statistical channel models from these measurements, it is shown that mmW systems can offer more than an order of magnitude increase in capacity over current state-of-the-art 4G cellular networks at current cell densities. Cellular systems, however, will need to be significantly redesigned to fully achieve these gains. Specifically, the requirement of highly directional and adaptive transmissions, directional isolation between links, and significant possibilities of outage have strong implications on multiple access, channel structure, synchronization, and receiver design. To address these challenges, the paper discusses how various technologies including adaptive beamforming, multihop relaying, heterogeneous network architectures, and carrier aggregation can be leveraged in the mmW context.
Citations
More filters
[...]
TL;DR: This paper discusses all of these topics, identifying key challenges for future research and preliminary 5G standardization activities, while providing a comprehensive overview of the current literature, and in particular of the papers appearing in this special issue.
Abstract: What will 5G be? What it will not be is an incremental advance on 4G. The previous four generations of cellular technology have each been a major paradigm shift that has broken backward compatibility. Indeed, 5G will need to be a paradigm shift that includes very high carrier frequencies with massive bandwidths, extreme base station and device densities, and unprecedented numbers of antennas. However, unlike the previous four generations, it will also be highly integrative: tying any new 5G air interface and spectrum together with LTE and WiFi to provide universal high-rate coverage and a seamless user experience. To support this, the core network will also have to reach unprecedented levels of flexibility and intelligence, spectrum regulation will need to be rethought and improved, and energy and cost efficiencies will become even more critical considerations. This paper discusses all of these topics, identifying key challenges for future research and preliminary 5G standardization activities, while providing a comprehensive overview of the current literature, and in particular of the papers appearing in this special issue.
7,139 citations
Cites background from "Millimeter-Wave Cellular Wireless N..."
...Marzetta was instrumental in articulating a vision in which the number of antennas increased by more than an order of magnitude, first in a 2007 presentation [89] with the details formalized in a landmark paper [90]....
[...]
TL;DR: This article provides an overview of signal processing challenges in mmWave wireless systems, with an emphasis on those faced by using MIMO communication at higher carrier frequencies.
Abstract: Communication at millimeter wave (mmWave) frequencies is defining a new era of wireless communication. The mmWave band offers higher bandwidth communication channels versus those presently used in commercial wireless systems. The applications of mmWave are immense: wireless local and personal area networks in the unlicensed band, 5G cellular systems, not to mention vehicular area networks, ad hoc networks, and wearables. Signal processing is critical for enabling the next generation of mmWave communication. Due to the use of large antenna arrays at the transmitter and receiver, combined with radio frequency and mixed signal power constraints, new multiple-input multiple-output (MIMO) communication signal processing techniques are needed. Because of the wide bandwidths, low complexity transceiver algorithms become important. There are opportunities to exploit techniques like compressed sensing for channel estimation and beamforming. This article provides an overview of signal processing challenges in mmWave wireless systems, with an emphasis on those faced by using MIMO communication at higher carrier frequencies.
2,380 citations
Cites background from "Millimeter-Wave Cellular Wireless N..."
...A major outstanding issue is characterizing the joint probabilities in outage between links from different cells, which is critical in assessing the benefits of macro-diversity [65], [66]....
[...]
TL;DR: Detailed spatial statistical models of the channels are derived and it is found that, even in highly non-line-of-sight environments, strong signals can be detected 100-200 m from potential cell sites, potentially with multiple clusters to support spatial multiplexing.
Abstract: With the severe spectrum shortage in conventional cellular bands, millimeter wave (mmW) frequencies between 30 and 300 GHz have been attracting growing attention as a possible candidate for next-generation micro- and picocellular wireless networks. The mmW bands offer orders of magnitude greater spectrum than current cellular allocations and enable very high-dimensional antenna arrays for further gains via beamforming and spatial multiplexing. This paper uses recent real-world measurements at 28 and 73 GHz in New York, NY, USA, to derive detailed spatial statistical models of the channels and uses these models to provide a realistic assessment of mmW micro- and picocellular networks in a dense urban deployment. Statistical models are derived for key channel parameters, including the path loss, number of spatial clusters, angular dispersion, and outage. It is found that, even in highly non-line-of-sight environments, strong signals can be detected 100-200 m from potential cell sites, potentially with multiple clusters to support spatial multiplexing. Moreover, a system simulation based on the models predicts that mmW systems can offer an order of magnitude increase in capacity over current state-of-the-art 4G cellular networks with no increase in cell density from current urban deployments.
2,102 citations
Cites background from "Millimeter-Wave Cellular Wireless N..."
...It should be noted that the capacity numbers reported in [9], which were based on an earlier version...
[...]
...widths are much wider than today’s cellular networks [4]–[9]....
[...]
TL;DR: An overview of 5G research, standardization trials, and deployment challenges is provided, with research test beds delivering promising performance but pre-commercial trials lagging behind the desired 5G targets.
Abstract: There is considerable pressure to define the key requirements of 5G, develop 5G standards, and perform technology trials as quickly as possible. Normally, these activities are best done in series but there is a desire to complete these tasks in parallel so that commercial deployments of 5G can begin by 2020. 5G will not be an incremental improvement over its predecessors; it aims to be a revolutionary leap forward in terms of data rates, latency, massive connectivity, network reliability, and energy efficiency. These capabilities are targeted at realizing high-speed connectivity, the Internet of Things, augmented virtual reality, the tactile internet, and so on. The requirements of 5G are expected to be met by new spectrum in the microwave bands (3.3-4.2 GHz), and utilizing large bandwidths available in mm-wave bands, increasing spatial degrees of freedom via large antenna arrays and 3-D MIMO, network densification, and new waveforms that provide scalability and flexibility to meet the varying demands of 5G services. Unlike the one size fits all 4G core networks, the 5G core network must be flexible and adaptable and is expected to simultaneously provide optimized support for the diverse 5G use case categories. In this paper, we provide an overview of 5G research, standardization trials, and deployment challenges. Due to the enormous scope of 5G systems, it is necessary to provide some direction in a tutorial article, and in this overview, the focus is largely user centric, rather than device centric. In addition to surveying the state of play in the area, we identify leading technologies, evaluating their strengths and weaknesses, and outline the key challenges ahead, with research test beds delivering promising performance but pre-commercial trials lagging behind the desired 5G targets.
1,659 citations
TL;DR: Experimental measurements and empirically-based propagation channel models for the 28, 38, 60, and 73 GHz mmWave bands are presented, using a wideband sliding correlator channel sounder with steerable directional horn antennas at both the transmitter and receiver from 2011 to 2013.
Abstract: The relatively unused millimeter-wave (mmWave) spectrum offers excellent opportunities to increase mobile capacity due to the enormous amount of available raw bandwidth. This paper presents experimental measurements and empirically-based propagation channel models for the 28, 38, 60, and 73 GHz mmWave bands, using a wideband sliding correlator channel sounder with steerable directional horn antennas at both the transmitter and receiver from 2011 to 2013. More than 15,000 power delay profiles were measured across the mmWave bands to yield directional and omnidirectional path loss models, temporal and spatial channel models, and outage probabilities. Models presented here offer side-by-side comparisons of propagation characteristics over a wide range of mmWave bands, and the results and models are useful for the research and standardization process of future mmWave systems. Directional and omnidirectional path loss models with respect to a 1 m close-in free space reference distance over a wide range of mmWave frequencies and scenarios using directional antennas in real-world environments are provided herein, and are shown to simplify mmWave path loss models, while allowing researchers to globally compare and standardize path loss parameters for emerging mmWave wireless networks. A new channel impulse response modeling framework, shown to agree with extensive mmWave measurements over several bands, is presented for use in link-layer simulations, using the observed fact that spatial lobes contain multipath energy that arrives at many different propagation time intervals. The results presented here may assist researchers in analyzing and simulating the performance of next-generation mmWave wireless networks that will rely on adaptive antennas and multiple-input and multiple-output (MIMO) antenna systems.
1,417 citations
Cites methods from "Millimeter-Wave Cellular Wireless N..."
...The floating intercept model parameters for the 28 and 73 GHz campaigns are slightly different here than those described in [40], due to an updated PDP thresholding algorithm that uses a more stringent 5 dB SNR threshold, and by separating the TX-RX path loss data points by RX antenna...
[...]
...A more detailed description of how the directional measurements were aggregated together to create omnidirectional models similar to those in [39] and [40] was presented in [38]....
[...]
References
More filters
15 Apr 2007
TL;DR: Simulation results within the context of the UMTS long-term evolution system indicate that, with half-wavelength antenna spacings and a typical power azimuth spectrum, the performance is close to optimal.
Abstract: This paper presents a low-complexity iterative algorithm for long-term transmit beamforming in multicast channels. Since it relies only on antenna correlations at the base station, the algorithm requires only infrequent feedback from the users. Multiantenna receivers are not required, but they are transparently accommodated. Simulation results within the context of the UMTS long-term evolution system indicate that, with half-wavelength antenna spacings and a typical power azimuth spectrum, the performance is close to optimal. The specific gains (in average SINR) then depend on the number of transmit antennas and the number of active users.
110 citations
"Millimeter-Wave Cellular Wireless N..." refers background in this paper
...However, we only considered long-term beamforming [87] to avoid tracking of small-scale fading, which may be slightly challenging at very high Doppler frequencies (e....
[...]
TL;DR: In this paper, an integrated monopulse radar receiver is developed for tracking applications at W-band frequencies, which is based on dielectric-lens-supported, coplanar-waveguide-fed slot-ring antennas integrated with /spl times/2 uniplanar subharmonic mixers.
Abstract: An integrated monopulse radar receiver has been developed for tracking applications at W-band frequencies. The receiver is based on dielectric-lens-supported, coplanar-waveguide-fed slot-ring antennas integrated with /spl times/2 uniplanar subharmonic mixers. The slot-ring antenna is capable of supporting two orthogonal modes offering the possibility of dual/multiple receive polarizations. The design center frequency is 94 GHz and the IF bandwidth is 2-4 GHz. The measured DSB conversion losses of the individual receiver channels range from 14.4 to 14.7 dB at an LO frequency of 45.0 GHz and an IF of 1.4 GHz. This includes the lens reflection and absorption losses, backside radiation, RF feedline loss, mixer conversion loss, and IF distribution loss. Excellent monopulse patterns are achieved with better than 45 dB difference pattern nulls using IF monopulse processing. This translates to submilliradian angular accuracy for a 24 mm aperture. Better than 25 dB nulls are possible over a 600 MHz bandwidth. The receiver is robust with respect to RF frequency.
104 citations
23 May 2010
TL;DR: A joint design of transmit-receive mixed analog/digital beamformers that aim at maximizing the received average signal-to-noise-ratio (SNR) and shows better performance than state-of-art solutions, which combine antenna selection techniques and digital beamforming.
Abstract: Multi-antenna architectures, where beamforming processing is shared between analog and digital, are of great interest for future multi-Gbps wireless systems operating at 60 GHz. In this spectrum band, wireless systems can integrate large antenna arrays in a very small volume thanks to a wavelength of about 5 mm and thus provide the required gain to meet the severe link budget. However, the cost and power consumption of an analog front-end (AFE) chain, that carries out translation between radio frequency (RF) and digital baseband, are too high at 60 GHz to afford one AFE for each antenna. In this paper, we consider low cost multi-antenna architectures with a lower number of AFE chains than antenna elements. We propose a joint design of transmit-receive mixed analog/digital beamformers that aim at maximizing the received average signal-to-noise-ratio (SNR). The proposed scheme shows better performance than state-of-art solutions, which combine antenna selection techniques and digital beamforming.
104 citations
25 Nov 2013
TL;DR: Data collected and processed from the measurements shows that strong received power can be achieved from the multipath-rich indoor environment, in the presence of multiple obstructions, and may be utilized for the design of future fifth generation millimeter wave indoor cellular systems.
Abstract: As the mobile cellular carriers are currently facing a spectrum crunch, researchers are concentrating on higher carrier frequency bands, such as E-band (71-76 GHz and 81-86 GHz) for the next generation wireless communication systems. The E-band is promising due to its large available, continuous bandwidth and robust weather resilience. In this paper, we demonstrate a spread spectrum sliding correlator channel sounder operating at a center frequency of 73.5 GHz with an 800 MHz null-to-null bandwidth. The channel sounder provides a multipath time resolution of 2.33 ns. 72 GHz millimeter wave propagation and penetration characteristics in an indoor office environment are investigated using the sliding correlator channel sounding system. Data collected and processed from the measurements shows that strong received power can be achieved from the multipath-rich indoor environment, in the presence of multiple obstructions. The data obtained from this measurement campaign may be utilized for the design of future fifth generation millimeter wave indoor cellular systems.
98 citations
"Millimeter-Wave Cellular Wireless N..." refers background in this paper
...Reasonable coverage will require that mmW cells be placed indoors [30], [32]....
[...]
...Therefore, a key risk in mmW cellular is outage caused by shadowing when no reflective or scattering paths can be found [31], [32]....
[...]
TL;DR: In this paper, the results of wideband measurements of indoor radio channels operating in a 2 GHz frequency band centred around 58 GHz were performed using a frequency step sounding technique and the results were presented of cell coverage and RMS delay spreas under both line-of-sight (LOS) and obstructed (OBS) situations.
Abstract: Wideband measurements of indoor radio channels operating in a 2 GHz frequency band centred around 58 GHz were performed using a frequency step sounding technique. The results are presented of cell coverage and RMS delay spreas under both line-of-sight (LOS) and obstructed (OBS) situations.
96 citations