scispace - formally typeset
Search or ask a question
Journal ArticleDOI

Oxide Semiconductor Thin‐Film Transistors: A Review of Recent Advances

12 Jun 2012-Advanced Materials (WILEY‐VCH Verlag)-Vol. 24, Iss: 22, pp 2945-2986
TL;DR: The recent progress in n- and p-type oxide based thin-film transistors (TFT) is reviewed, with special emphasis on solution-processed andp-type, and the major milestones already achieved with this emerging and very promising technology are summarizeed.
Abstract: Transparent electronics is today one of the most advanced topics for a wide range of device applications. The key components are wide bandgap semiconductors, where oxides of different origins play an important role, not only as passive component but also as active component, similar to what is observed in conventional semiconductors like silicon. Transparent electronics has gained special attention during the last few years and is today established as one of the most promising technologies for leading the next generation of flat panel display due to its excellent electronic performance. In this paper the recent progress in n- and p-type oxide based thin-film transistors (TFT) is reviewed, with special emphasis on solution-processed and p-type, and the major milestones already achieved with this emerging and very promising technology are summarizeed. After a short introduction where the main advantages of these semiconductors are presented, as well as the industry expectations, the beautiful history of TFTs is revisited, including the main landmarks in the last 80 years, finishing by referring to some papers that have played an important role in shaping transparent electronics. Then, an overview is presented of state of the art n-type TFTs processed by physical vapour deposition methods, and finally one of the most exciting, promising, and low cost but powerful technologies is discussed: solution-processed oxide TFTs. Moreover, a more detailed focus analysis will be given concerning p-type oxide TFTs, mainly centred on two of the most promising semiconductor candidates: copper oxide and tin oxide. The most recent data related to the production of complementary metal oxide semiconductor (CMOS) devices based on n- and p-type oxide TFT is also be presented. The last topic of this review is devoted to some emerging applications, finalizing with the main conclusions. Related work that originated at CENIMAT|I3N during the last six years is included in more detail, which has led to the fabrication of high performance n- and p-type oxide transistors as well as the fabrication of CMOS devices with and on paper.
Citations
More filters
Journal ArticleDOI
TL;DR: In this article, a flexible organic semiconductor was fabricated by incorporating multiwall carbon nanotubes (MWNTs) into insulating poly(dimethylsiloxane) (PDMS) rubber, and researched the contact properties in the metal/composite junctions.
Abstract: Organic semiconductors have attracted great attention offering an attractive alternative to conventional inorganic semiconductors due to lower costs, simpler synthesis and high flexibility. In this work, we fabricated a flexible organic semiconductor by incorporating multiwall carbon nanotubes (MWNTs) into insulating poly(dimethylsiloxane) (PDMS) rubber, and researched the contact properties in the metal/composite junctions. The results reveal that the contact properties depend largely on the work function of the metals and the MWNT loading of the composites. To ascertain the performance variations of the copper/composite junctions characterized by important parameters, Schottky Barrier Heights (SBHs) were measured with various MWNT loading of the composites. The SBH decreased with the increase of the MWNT loading, exceeded 0.783 eV for the 0.35 wt% composite, and shared the same changing trend with the composite Coulomb band gap as a function of the MWNT loading. A quantitative analysis of photo-voltages by the photovoltaic tests was used to verify the reliability of these SBHs. The stability test provides direct evidence that the composites possess good, durable performances at ambient temperature. This work shows that the contact properties in the metal/composite junctions cannot be neglected in the application of the composites in flexible electronics.

8 citations

Journal ArticleDOI
R. Dridi1, M. BenAmor, N. Mahdhi, A. Amlouk, K. Boubaker, Mosbah Amlouk 
TL;DR: In this paper, the structural and optical properties of non-crystalline zinc nickel oxide have been examined using XRD and UV-visible spectrophotometry, which revealed a hydrophilic character.
Abstract: Non-crystalline zinc nickel oxide has been deposited on glass substrate using spray pyrolysis. The structural and optical properties were examined using XRD and UV–visible spectrophotometry. These films are characterized by a direct band gap and the optical band gap energy value is lying between 3.66 eV and 3.79 eV. The electrical conductivity was investigated at different temperatures (330–450 °C) by using the impedance spectroscopy technique in a frequency range from 5 Hz to 13 MHz. The value of s is dependent on temperature, which tends to decrease depending on the temperature. The temperature dependence of both the AC conductivity and the parameter s is interpreted by the correlated barrier hopping (CBH) model. These films revealed a hydrophilic character. Moreover, in the presence of these samples, a photodegradation of methyl blue (MB) and effective mineralization occurred; 14 mg/L of MB was degraded within 120 min. Finally, elements from the Lattice Compatibility Theory were presented in order to understand partial non-crystallization of the ZnO-NiO binary structure.

8 citations

Journal ArticleDOI
TL;DR: In this article, a 1D model with a constant density of interface states above and below the conduction band edge is used to explain the current-voltage characteristic of thin-film transistors.
Abstract: Thin-film transistors were fabricated using 45-nm thick ZnO deposited by pulsed laser deposition and 15-nm thick Al2O3 gate insulator deposited by atomic layer deposition. A 1-D model with a constant density of interface states above and below the conduction band edge is used to explain the current-voltage characteristic. This model does not create distortion of transconductance versus gate voltage at low gate voltage that can be created by exponential tail or Gaussian distributions of interface states. The “subthreshold” regime is at the top ZnO surface away from the bottom gate, but subthreshold swing is controlled by interface states at the ZnO/Al2O3 bottom interface. The observed increase in mobility with gate voltage is delayed by filling of the interface states above the conduction band edge. Interface state filling and a rapid increase in mobility with increased gate voltage produce an apparent large threshold voltage as extrapolated from a linear fit to current measured at large gate voltage. The difference between threshold voltage and turn-off voltage is an important figure of merit (FOM) that should be kept as small as possible. In this paper, FOM is 2.5 and 1.8 V for 0.1 and 6 V drain voltage, respectively.

8 citations

Journal ArticleDOI
TL;DR: In this article, a solution-processed indium oxide (In2O3) TFT with ODS-ZrO2 film as the gate dielectric showed excellent electrical performance, for example high carrier mobility up to 62.02 cm2 V s−1, a large on/off drain current ratio of 3.0 × 106, a small sub-threshold swing of 0.14 V and excellent bias stress stability.
Abstract: Solution deposition of high-quality dielectric films is one of the big challenges in achieving excellent electrical performance of bi-layer solution-processed metal oxide (MO) thin film transistors (TFTs). Using an oxygen-doped precursor solution (ODS), we successfully deposited high-quality zirconium oxide (ZrO2) dielectric films by a solution process. The ODS-ZrO2 films show low leakage current density (10−7 A cm−2 at 2 MV cm−1), high breakdown electric field (7.0 MV cm−1) and high permittivity (19.5). Consequently, solution-processed indium oxide (In2O3) TFTs with ODS-ZrO2 film as the gate dielectric show excellent electrical performance, for example high carrier mobility up to 62.02 cm2 V s−1, a large on/off drain current ratio of 3.0 × 106, a small subthreshold swing of 0.14 V and excellent bias stress stability. Our work demonstrates the critical role of the dielectric film in the electrical performance of MO-TFTs. More importantly, we reveal that high dielectric constant (κ) dielectric film deposited with ODS should be an effective way to significantly increase the electrical properties of MO-TFTs for future low-cost, high-performance applications.

8 citations

Journal ArticleDOI
TL;DR: In this paper, a buffer layer between the active layer and the insulating layer was proposed to narrow the intersecting region, and the effect of buffer layer was investigated by the multifactor analysis on Minitab software.

8 citations

References
More filters
Journal ArticleDOI
25 Nov 2004-Nature
TL;DR: A novel semiconducting material is proposed—namely, a transparent amorphous oxide semiconductor from the In-Ga-Zn-O system (a-IGZO)—for the active channel in transparent thin-film transistors (TTFTs), which are fabricated on polyethylene terephthalate sheets and exhibit saturation mobilities and device characteristics are stable during repetitive bending of the TTFT sheet.
Abstract: Transparent electronic devices formed on flexible substrates are expected to meet emerging technological demands where silicon-based electronics cannot provide a solution. Examples of active flexible applications include paper displays and wearable computers1. So far, mainly flexible devices based on hydrogenated amorphous silicon (a-Si:H)2,3,4,5 and organic semiconductors2,6,7,8,9,10 have been investigated. However, the performance of these devices has been insufficient for use as transistors in practical computers and current-driven organic light-emitting diode displays. Fabricating high-performance devices is challenging, owing to a trade-off between processing temperature and device performance. Here, we propose to solve this problem by using a novel semiconducting material—namely, a transparent amorphous oxide semiconductor from the In-Ga-Zn-O system (a-IGZO)—for the active channel in transparent thin-film transistors (TTFTs). The a-IGZO is deposited on polyethylene terephthalate at room temperature and exhibits Hall effect mobilities exceeding 10 cm2 V-1 s-1, which is an order of magnitude larger than for hydrogenated amorphous silicon. TTFTs fabricated on polyethylene terephthalate sheets exhibit saturation mobilities of 6–9 cm2 V-1 s-1, and device characteristics are stable during repetitive bending of the TTFT sheet.

7,301 citations

Book
04 Jul 1990
TL;DR: In this article, the authors present a characterization of the resistivity of a two-point-versus-four-point probe in terms of the number of contacts and the amount of contacts in the probe.
Abstract: Preface to Third Edition. 1 Resistivity. 1.1 Introduction. 1.2 Two-Point Versus Four-Point Probe. 1.3 Wafer Mapping. 1.4 Resistivity Profiling. 1.5 Contactless Methods. 1.6 Conductivity Type. 1.7 Strengths and Weaknesses. Appendix 1.1 Resistivity as a Function of Doping Density. Appendix 1.2 Intrinsic Carrier Density. References. Problems. Review Questions. 2 Carrier and Doping Density. 2.1 Introduction. 2.2 Capacitance-Voltage (C-V). 2.3 Current-Voltage (I-V). 2.4 Measurement Errors and Precautions. 2.5 Hall Effect. 2.6 Optical Techniques. 2.7 Secondary Ion Mass Spectrometry (SIMS). 2.8 Rutherford Backscattering (RBS). 2.9 Lateral Profiling. 2.10 Strengths and Weaknesses. Appendix 2.1 Parallel or Series Connection? Appendix 2.2 Circuit Conversion. References. Problems. Review Questions. 3 Contact Resistance and Schottky Barriers. 3.1 Introduction. 3.2 Metal-Semiconductor Contacts. 3.3 Contact Resistance. 3.4 Measurement Techniques. 3.5 Schottky Barrier Height. 3.6 Comparison of Methods. 3.7 Strengths and Weaknesses. Appendix 3.1 Effect of Parasitic Resistance. Appendix 3.2 Alloys for Contacts to Semiconductors. References. Problems. Review Questions. 4 Series Resistance, Channel Length and Width, and Threshold Voltage. 4.1 Introduction. 4.2 PN Junction Diodes. 4.3 Schottky Barrier Diodes. 4.4 Solar Cells. 4.5 Bipolar Junction Transistors. 4.6 MOSFETS. 4.7 MESFETS and MODFETS. 4.8 Threshold Voltage. 4.9 Pseudo MOSFET. 4.10 Strengths and Weaknesses. Appendix 4.1 Schottky Diode Current-Voltage Equation. References. Problems. Review Questions. 5 Defects. 5.1 Introduction. 5.2 Generation-Recombination Statistics. 5.3 Capacitance Measurements. 5.4 Current Measurements. 5.5 Charge Measurements. 5.6 Deep-Level Transient Spectroscopy (DLTS). 5.7 Thermally Stimulated Capacitance and Current. 5.8 Positron Annihilation Spectroscopy (PAS). 5.9 Strengths and Weaknesses. Appendix 5.1 Activation Energy and Capture Cross-Section. Appendix 5.2 Time Constant Extraction. Appendix 5.3 Si and GaAs Data. References. Problems. Review Questions. 6 Oxide and Interface Trapped Charges, Oxide Thickness. 6.1 Introduction. 6.2 Fixed, Oxide Trapped, and Mobile Oxide Charge. 6.3 Interface Trapped Charge. 6.4 Oxide Thickness. 6.5 Strengths and Weaknesses. Appendix 6.1 Capacitance Measurement Techniques. Appendix 6.2 Effect of Chuck Capacitance and Leakage Current. References. Problems. Review Questions. 7 Carrier Lifetimes. 7.1 Introduction. 7.2 Recombination Lifetime/Surface Recombination Velocity. 7.3 Generation Lifetime/Surface Generation Velocity. 7.4 Recombination Lifetime-Optical Measurements. 7.5 Recombination Lifetime-Electrical Measurements. 7.6 Generation Lifetime-Electrical Measurements. 7.7 Strengths and Weaknesses. Appendix 7.1 Optical Excitation. Appendix 7.2 Electrical Excitation. References. Problems. Review Questions. 8 Mobility. 8.1 Introduction. 8.2 Conductivity Mobility. 8.3 Hall Effect and Mobility. 8.4 Magnetoresistance Mobility. 8.5 Time-of-Flight Drift Mobility. 8.6 MOSFET Mobility. 8.7 Contactless Mobility. 8.8 Strengths and Weaknesses. Appendix 8.1 Semiconductor Bulk Mobilities. Appendix 8.2 Semiconductor Surface Mobilities. Appendix 8.3 Effect of Channel Frequency Response. Appendix 8.4 Effect of Interface Trapped Charge. References. Problems. Review Questions. 9 Charge-based and Probe Characterization. 9.1 Introduction. 9.2 Background. 9.3 Surface Charging. 9.4 The Kelvin Probe. 9.5 Applications. 9.6 Scanning Probe Microscopy (SPM). 9.7 Strengths and Weaknesses. References. Problems. Review Questions. 10 Optical Characterization. 10.1 Introduction. 10.2 Optical Microscopy. 10.3 Ellipsometry. 10.4 Transmission. 10.5 Reflection. 10.6 Light Scattering. 10.7 Modulation Spectroscopy. 10.8 Line Width. 10.9 Photoluminescence (PL). 10.10 Raman Spectroscopy. 10.11 Strengths and Weaknesses. Appendix 10.1 Transmission Equations. Appendix 10.2 Absorption Coefficients and Refractive Indices for Selected Semiconductors. References. Problems. Review Questions. 11 Chemical and Physical Characterization. 11.1 Introduction. 11.2 Electron Beam Techniques. 11.3 Ion Beam Techniques. 11.4 X-Ray and Gamma-Ray Techniques. 11.5 Strengths and Weaknesses. Appendix 11.1 Selected Features of Some Analytical Techniques. References. Problems. Review Questions. 12 Reliability and Failure Analysis. 12.1 Introduction. 12.2 Failure Times and Acceleration Factors. 12.3 Distribution Functions. 12.4 Reliability Concerns. 12.5 Failure Analysis Characterization Techniques. 12.6 Strengths and Weaknesses. Appendix 12.1 Gate Currents. References. Problems. Review Questions. Appendix 1 List of Symbols. Appendix 2 Abbreviations and Acronyms. Index.

6,573 citations

Journal ArticleDOI
TL;DR: In this paper, a review of the literature in the area of alternate gate dielectrics is given, based on reported results and fundamental considerations, the pseudobinary materials systems offer large flexibility and show the most promise toward success.
Abstract: Many materials systems are currently under consideration as potential replacements for SiO2 as the gate dielectric material for sub-0.1 μm complementary metal–oxide–semiconductor (CMOS) technology. A systematic consideration of the required properties of gate dielectrics indicates that the key guidelines for selecting an alternative gate dielectric are (a) permittivity, band gap, and band alignment to silicon, (b) thermodynamic stability, (c) film morphology, (d) interface quality, (e) compatibility with the current or expected materials to be used in processing for CMOS devices, (f) process compatibility, and (g) reliability. Many dielectrics appear favorable in some of these areas, but very few materials are promising with respect to all of these guidelines. A review of current work and literature in the area of alternate gate dielectrics is given. Based on reported results and fundamental considerations, the pseudobinary materials systems offer large flexibility and show the most promise toward success...

5,711 citations

Journal ArticleDOI
TL;DR: In this article, the authors present new insight into conduction mechanisms and performance characteristics, as well as opportunities for modeling properties of organic thin-film transistors (OTFTs) and discuss progress in the growing field of n-type OTFTs.
Abstract: Organic thin-film transistors (OTFTs) have lived to see great improvements in recent years. This review presents new insight into conduction mechanisms and performance characteristics, as well as opportunities for modeling properties of OTFTs. The shifted focus in research from novel chemical structures to fabrication technologies that optimize morphology and structural order is underscored by chapters on vacuum-deposited and solution-processed organic semiconducting films. Finally, progress in the growing field of the n-type OTFTs is discussed in ample detail. The Figure, showing a pentacene film edge on SiO2, illustrates the morphology issue.

4,804 citations

Journal ArticleDOI
TL;DR: An outlook is presented on what will be required to drive this young photovoltaic technology towards the next major milestone, a 10% power conversion efficiency, considered by many to represent the efficiency at which OPV can be adopted in wide-spread applications.
Abstract: Solution-processed bulk-heterojunction solar cells have gained serious attention during the last few years and are becoming established as one of the future photovoltaic technologies for low-cost power production. This article reviews the highlights of the last few years, and summarizes today's state-of-the-art performance. An outlook is given on relevant future materials and technologies that have the potential to guide this young photovoltaic technology towards the magic 10% regime. A cost model supplements the technical discussions, with practical aspects any photovoltaic technology needs to fulfil, and answers to the question as to whether low module costs can compensate lower lifetimes and performances.

3,084 citations