Oxide Semiconductor Thin‐Film Transistors: A Review of Recent Advances
TL;DR: The recent progress in n- and p-type oxide based thin-film transistors (TFT) is reviewed, with special emphasis on solution-processed andp-type, and the major milestones already achieved with this emerging and very promising technology are summarizeed.
Abstract: Transparent electronics is today one of the most advanced topics for a wide range of device applications. The key components are wide bandgap semiconductors, where oxides of different origins play an important role, not only as passive component but also as active component, similar to what is observed in conventional semiconductors like silicon. Transparent electronics has gained special attention during the last few years and is today established as one of the most promising technologies for leading the next generation of flat panel display due to its excellent electronic performance. In this paper the recent progress in n- and p-type oxide based thin-film transistors (TFT) is reviewed, with special emphasis on solution-processed and p-type, and the major milestones already achieved with this emerging and very promising technology are summarizeed. After a short introduction where the main advantages of these semiconductors are presented, as well as the industry expectations, the beautiful history of TFTs is revisited, including the main landmarks in the last 80 years, finishing by referring to some papers that have played an important role in shaping transparent electronics. Then, an overview is presented of state of the art n-type TFTs processed by physical vapour deposition methods, and finally one of the most exciting, promising, and low cost but powerful technologies is discussed: solution-processed oxide TFTs. Moreover, a more detailed focus analysis will be given concerning p-type oxide TFTs, mainly centred on two of the most promising semiconductor candidates: copper oxide and tin oxide. The most recent data related to the production of complementary metal oxide semiconductor (CMOS) devices based on n- and p-type oxide TFT is also be presented. The last topic of this review is devoted to some emerging applications, finalizing with the main conclusions. Related work that originated at CENIMAT|I3N during the last six years is included in more detail, which has led to the fabrication of high performance n- and p-type oxide transistors as well as the fabrication of CMOS devices with and on paper.
Citations
More filters
TL;DR: In this article, a review of recent researches performed to improve the PCE of organic-inorganic perovskite solar cells using different classes of HTMs are studied.
Abstract: Currently, several kinds of solar cells are developed and among them, organic-inorganic perovskite solar cells (PSCs) have received substantial interest because they have shown panchromatic light absorption capacities using low amounts of earth abundant materials, low exciton recombination rate, high carrier mobility and high solar to electrical power conversion efficiencies (PCEs) which can exceed 22%. In most PSCs, methylammonium lead iodide (CH3NH3PbI3 or MAPbI3) semiconductor perovskite is sandwiched between an electron transport material (ETM, n-type material) and a hole transport material (HTM, a p-type material). Two kinds of n-i-p and p-i-n configurations are fabricated which depends on the relative positions of the ETM and HTM layers in the device. The ETM in the n-i-p solar cell is usually a planar or mesoporous TiO2 thin film in which the perovskite solution is infiltrated. A disadvantage of the n-i-p cell is using very expensive HTM, 2,2′,7,7′-tetrakis(N,N-di-p-methoxyphenyl-amine)9,9′-spirobifluorene (spiro-OMeTAD). Although numerous HTMs have been introduced, spiro-OMeTAD is the most efficient HTM. Nonetheless, spiro-OMeTAD must be ultra-pure to produce high performance and this increases its price which is not cost-effective from economical viewpoint. Additionally, its pristine form performs badly and doping is necessary to improve its hole-mobility and conductivity. Also, the common dopants including 4-tert-butylpyridine, lithium salts and cobalt complex are corrosive and very hygroscopic which result in the device instability. In the p-i-n cells, poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) is extensively utilized as the HTM which is UV-unstable and hydrophilic that makes the device unstable. Furthermore, it is only deposited through solution coating process and shows acidic property that reacts with its underlying transparent conductive oxide. Thus, many attempts have been done to substitute the spiro-OMeTAD with other materials to find HTMs suitable for commercialization of PSCs. In this review, recent researches performed to improve the PCEs of PSCs using different classes of HTMs are studied.
80 citations
TL;DR: In this paper, the electron donating capacity of PEI combined with charge trapping and variation in the matrix film microstructure yields, for optimum PEI doping concentrations of 1.0% −1.5%, electron mobilities as high as ≈9 cm2 V−1 s−1 on a 300 nm SiO2 gate dielectric, an excellent on/off ratio of ≈107, and an application optimal V T.
Abstract: Polymer doping of solution-processed In2O3 with small amounts of the electron-rich polymer, polyethylenimine (PEI), affords superior transistor performance, including higher electron mobility than that of the pristine In2O3 matrix. PEI doping of In2O3 films not only frustrates crystallization and controls the carrier concentration but, more importantly, acts as electron dopant and/or scattering center depending on the polymer doping concentration. The electron donating capacity of PEI combined with charge trapping and variation in the matrix film microstructure yields, for optimum PEI doping concentrations of 1.0%–1.5%, electron mobilities as high as ≈9 cm2 V−1 s−1 on a 300 nm SiO2 gate dielectric, an excellent on/off ratio of ≈107, and an application optimal V T. Importantly, these metrics exceed those of the pure In2O3 matrix with a maximum mobility ≈4 cm2 V−1 s−1. Furthermore, we show that this approach is extendible to other oxide compositions such as IZO and the technologically relevant IGZO. This work opens a new means to fabricate amorphous semiconductors via solution processing at low temperatures, while preserving or enhancing the mobility of the pristine polycrystalline semiconductor.
80 citations
TL;DR: A flexible AMOLED display driven by oxide thin film transistors (TFTs) with anodic AlOx gate dielectric on a polyethylene naphthalate (PEN) substrate with a process temperature below 150 °C was reported in this paper.
Abstract: We report a flexible AMOLED display driven by oxide thin film transistors (TFTs) with anodic AlOx gate dielectric on a polyethylene naphthalate (PEN) substrate with a process temperature below 150 °C. The TFTs exhibit a field-effect mobility of 12.87 cm2 V−1 s−1, a subthreshold swing of 0.20 V dec−1, and an Ion/Ioff ratio of 109.
78 citations
TL;DR: In this paper, the authors review fundamental aspects and recent advances in emerging devices, and project their perspectives on their future, and regard hybrid electronics from organic semiconductors and graphene as a distinct subject of research that may open up many new possibilities.
Abstract: Both organic semiconductors and graphene now represent an established field of research with great technological potential. Recently, impressive progress has been made in our understanding of how to synergistically exploit their basic properties as unique functions in practical applications. It is therefore time to regard hybrid electronics from organic semiconductors and graphene as a distinct subject of research that may open up many new possibilities. This article reviews fundamental aspects and recent advances in emerging devices, and projects our perspectives on their future.
78 citations
TL;DR: Density functional theory calculations indicated that β-CuGaO2 is a direct semiconductor and intense absorption of light occurs near the band edge, which render this new material promising as an absorber in solar cells.
Abstract: An oxide semiconductor β-CuGaO2 with a wurtzite-derived β-NaFeO2 structure has been synthesized. Structural characterization has been carried out by Rietveld analysis using XRD and SAED, and it was shown that the lattice size is very close to that of zinc oxide. The optical absorption spectrum indicated that the band gap is 1.47 eV, which matches the band gap required to achieve the theoretical maximum conversion efficiency for a single-junction solar cell. The thermoelectromotive force indicated p-type conduction in its intrinsic state. Density functional theory calculations were performed to understand the electronic structure and optical properties of the semiconductor. These calculations indicated that β-CuGaO2 is a direct semiconductor and intense absorption of light occurs near the band edge. These properties render this new material promising as an absorber in solar cells.
77 citations
References
More filters
TL;DR: A novel semiconducting material is proposed—namely, a transparent amorphous oxide semiconductor from the In-Ga-Zn-O system (a-IGZO)—for the active channel in transparent thin-film transistors (TTFTs), which are fabricated on polyethylene terephthalate sheets and exhibit saturation mobilities and device characteristics are stable during repetitive bending of the TTFT sheet.
Abstract: Transparent electronic devices formed on flexible substrates are expected to meet emerging technological demands where silicon-based electronics cannot provide a solution. Examples of active flexible applications include paper displays and wearable computers1. So far, mainly flexible devices based on hydrogenated amorphous silicon (a-Si:H)2,3,4,5 and organic semiconductors2,6,7,8,9,10 have been investigated. However, the performance of these devices has been insufficient for use as transistors in practical computers and current-driven organic light-emitting diode displays. Fabricating high-performance devices is challenging, owing to a trade-off between processing temperature and device performance. Here, we propose to solve this problem by using a novel semiconducting material—namely, a transparent amorphous oxide semiconductor from the In-Ga-Zn-O system (a-IGZO)—for the active channel in transparent thin-film transistors (TTFTs). The a-IGZO is deposited on polyethylene terephthalate at room temperature and exhibits Hall effect mobilities exceeding 10 cm2 V-1 s-1, which is an order of magnitude larger than for hydrogenated amorphous silicon. TTFTs fabricated on polyethylene terephthalate sheets exhibit saturation mobilities of 6–9 cm2 V-1 s-1, and device characteristics are stable during repetitive bending of the TTFT sheet.
7,301 citations
Book•
04 Jul 1990
TL;DR: In this article, the authors present a characterization of the resistivity of a two-point-versus-four-point probe in terms of the number of contacts and the amount of contacts in the probe.
Abstract: Preface to Third Edition. 1 Resistivity. 1.1 Introduction. 1.2 Two-Point Versus Four-Point Probe. 1.3 Wafer Mapping. 1.4 Resistivity Profiling. 1.5 Contactless Methods. 1.6 Conductivity Type. 1.7 Strengths and Weaknesses. Appendix 1.1 Resistivity as a Function of Doping Density. Appendix 1.2 Intrinsic Carrier Density. References. Problems. Review Questions. 2 Carrier and Doping Density. 2.1 Introduction. 2.2 Capacitance-Voltage (C-V). 2.3 Current-Voltage (I-V). 2.4 Measurement Errors and Precautions. 2.5 Hall Effect. 2.6 Optical Techniques. 2.7 Secondary Ion Mass Spectrometry (SIMS). 2.8 Rutherford Backscattering (RBS). 2.9 Lateral Profiling. 2.10 Strengths and Weaknesses. Appendix 2.1 Parallel or Series Connection? Appendix 2.2 Circuit Conversion. References. Problems. Review Questions. 3 Contact Resistance and Schottky Barriers. 3.1 Introduction. 3.2 Metal-Semiconductor Contacts. 3.3 Contact Resistance. 3.4 Measurement Techniques. 3.5 Schottky Barrier Height. 3.6 Comparison of Methods. 3.7 Strengths and Weaknesses. Appendix 3.1 Effect of Parasitic Resistance. Appendix 3.2 Alloys for Contacts to Semiconductors. References. Problems. Review Questions. 4 Series Resistance, Channel Length and Width, and Threshold Voltage. 4.1 Introduction. 4.2 PN Junction Diodes. 4.3 Schottky Barrier Diodes. 4.4 Solar Cells. 4.5 Bipolar Junction Transistors. 4.6 MOSFETS. 4.7 MESFETS and MODFETS. 4.8 Threshold Voltage. 4.9 Pseudo MOSFET. 4.10 Strengths and Weaknesses. Appendix 4.1 Schottky Diode Current-Voltage Equation. References. Problems. Review Questions. 5 Defects. 5.1 Introduction. 5.2 Generation-Recombination Statistics. 5.3 Capacitance Measurements. 5.4 Current Measurements. 5.5 Charge Measurements. 5.6 Deep-Level Transient Spectroscopy (DLTS). 5.7 Thermally Stimulated Capacitance and Current. 5.8 Positron Annihilation Spectroscopy (PAS). 5.9 Strengths and Weaknesses. Appendix 5.1 Activation Energy and Capture Cross-Section. Appendix 5.2 Time Constant Extraction. Appendix 5.3 Si and GaAs Data. References. Problems. Review Questions. 6 Oxide and Interface Trapped Charges, Oxide Thickness. 6.1 Introduction. 6.2 Fixed, Oxide Trapped, and Mobile Oxide Charge. 6.3 Interface Trapped Charge. 6.4 Oxide Thickness. 6.5 Strengths and Weaknesses. Appendix 6.1 Capacitance Measurement Techniques. Appendix 6.2 Effect of Chuck Capacitance and Leakage Current. References. Problems. Review Questions. 7 Carrier Lifetimes. 7.1 Introduction. 7.2 Recombination Lifetime/Surface Recombination Velocity. 7.3 Generation Lifetime/Surface Generation Velocity. 7.4 Recombination Lifetime-Optical Measurements. 7.5 Recombination Lifetime-Electrical Measurements. 7.6 Generation Lifetime-Electrical Measurements. 7.7 Strengths and Weaknesses. Appendix 7.1 Optical Excitation. Appendix 7.2 Electrical Excitation. References. Problems. Review Questions. 8 Mobility. 8.1 Introduction. 8.2 Conductivity Mobility. 8.3 Hall Effect and Mobility. 8.4 Magnetoresistance Mobility. 8.5 Time-of-Flight Drift Mobility. 8.6 MOSFET Mobility. 8.7 Contactless Mobility. 8.8 Strengths and Weaknesses. Appendix 8.1 Semiconductor Bulk Mobilities. Appendix 8.2 Semiconductor Surface Mobilities. Appendix 8.3 Effect of Channel Frequency Response. Appendix 8.4 Effect of Interface Trapped Charge. References. Problems. Review Questions. 9 Charge-based and Probe Characterization. 9.1 Introduction. 9.2 Background. 9.3 Surface Charging. 9.4 The Kelvin Probe. 9.5 Applications. 9.6 Scanning Probe Microscopy (SPM). 9.7 Strengths and Weaknesses. References. Problems. Review Questions. 10 Optical Characterization. 10.1 Introduction. 10.2 Optical Microscopy. 10.3 Ellipsometry. 10.4 Transmission. 10.5 Reflection. 10.6 Light Scattering. 10.7 Modulation Spectroscopy. 10.8 Line Width. 10.9 Photoluminescence (PL). 10.10 Raman Spectroscopy. 10.11 Strengths and Weaknesses. Appendix 10.1 Transmission Equations. Appendix 10.2 Absorption Coefficients and Refractive Indices for Selected Semiconductors. References. Problems. Review Questions. 11 Chemical and Physical Characterization. 11.1 Introduction. 11.2 Electron Beam Techniques. 11.3 Ion Beam Techniques. 11.4 X-Ray and Gamma-Ray Techniques. 11.5 Strengths and Weaknesses. Appendix 11.1 Selected Features of Some Analytical Techniques. References. Problems. Review Questions. 12 Reliability and Failure Analysis. 12.1 Introduction. 12.2 Failure Times and Acceleration Factors. 12.3 Distribution Functions. 12.4 Reliability Concerns. 12.5 Failure Analysis Characterization Techniques. 12.6 Strengths and Weaknesses. Appendix 12.1 Gate Currents. References. Problems. Review Questions. Appendix 1 List of Symbols. Appendix 2 Abbreviations and Acronyms. Index.
6,573 citations
TL;DR: In this paper, a review of the literature in the area of alternate gate dielectrics is given, based on reported results and fundamental considerations, the pseudobinary materials systems offer large flexibility and show the most promise toward success.
Abstract: Many materials systems are currently under consideration as potential replacements for SiO2 as the gate dielectric material for sub-0.1 μm complementary metal–oxide–semiconductor (CMOS) technology. A systematic consideration of the required properties of gate dielectrics indicates that the key guidelines for selecting an alternative gate dielectric are (a) permittivity, band gap, and band alignment to silicon, (b) thermodynamic stability, (c) film morphology, (d) interface quality, (e) compatibility with the current or expected materials to be used in processing for CMOS devices, (f) process compatibility, and (g) reliability. Many dielectrics appear favorable in some of these areas, but very few materials are promising with respect to all of these guidelines. A review of current work and literature in the area of alternate gate dielectrics is given. Based on reported results and fundamental considerations, the pseudobinary materials systems offer large flexibility and show the most promise toward success...
5,711 citations
IBM1
TL;DR: In this article, the authors present new insight into conduction mechanisms and performance characteristics, as well as opportunities for modeling properties of organic thin-film transistors (OTFTs) and discuss progress in the growing field of n-type OTFTs.
Abstract: Organic thin-film transistors (OTFTs) have lived to see great improvements in recent years. This review presents new insight into conduction mechanisms and performance characteristics, as well as opportunities for modeling properties of OTFTs. The shifted focus in research from novel chemical structures to fabrication technologies that optimize morphology and structural order is underscored by chapters on vacuum-deposited and solution-processed organic semiconducting films. Finally, progress in the growing field of the n-type OTFTs is discussed in ample detail. The Figure, showing a pentacene film edge on SiO2, illustrates the morphology issue.
4,804 citations
TL;DR: An outlook is presented on what will be required to drive this young photovoltaic technology towards the next major milestone, a 10% power conversion efficiency, considered by many to represent the efficiency at which OPV can be adopted in wide-spread applications.
Abstract: Solution-processed bulk-heterojunction solar cells have gained serious attention during the last few years and are becoming established as one of the future photovoltaic technologies for low-cost power production. This article reviews the highlights of the last few years, and summarizes today's state-of-the-art performance. An outlook is given on relevant future materials and technologies that have the potential to guide this young photovoltaic technology towards the magic 10% regime. A cost model supplements the technical discussions, with practical aspects any photovoltaic technology needs to fulfil, and answers to the question as to whether low module costs can compensate lower lifetimes and performances.
3,084 citations