Oxide Semiconductor Thin‐Film Transistors: A Review of Recent Advances
TL;DR: The recent progress in n- and p-type oxide based thin-film transistors (TFT) is reviewed, with special emphasis on solution-processed andp-type, and the major milestones already achieved with this emerging and very promising technology are summarizeed.
Abstract: Transparent electronics is today one of the most advanced topics for a wide range of device applications. The key components are wide bandgap semiconductors, where oxides of different origins play an important role, not only as passive component but also as active component, similar to what is observed in conventional semiconductors like silicon. Transparent electronics has gained special attention during the last few years and is today established as one of the most promising technologies for leading the next generation of flat panel display due to its excellent electronic performance. In this paper the recent progress in n- and p-type oxide based thin-film transistors (TFT) is reviewed, with special emphasis on solution-processed and p-type, and the major milestones already achieved with this emerging and very promising technology are summarizeed. After a short introduction where the main advantages of these semiconductors are presented, as well as the industry expectations, the beautiful history of TFTs is revisited, including the main landmarks in the last 80 years, finishing by referring to some papers that have played an important role in shaping transparent electronics. Then, an overview is presented of state of the art n-type TFTs processed by physical vapour deposition methods, and finally one of the most exciting, promising, and low cost but powerful technologies is discussed: solution-processed oxide TFTs. Moreover, a more detailed focus analysis will be given concerning p-type oxide TFTs, mainly centred on two of the most promising semiconductor candidates: copper oxide and tin oxide. The most recent data related to the production of complementary metal oxide semiconductor (CMOS) devices based on n- and p-type oxide TFT is also be presented. The last topic of this review is devoted to some emerging applications, finalizing with the main conclusions. Related work that originated at CENIMAT|I3N during the last six years is included in more detail, which has led to the fabrication of high performance n- and p-type oxide transistors as well as the fabrication of CMOS devices with and on paper.
Citations
More filters
TL;DR: X-ray reflectometry analysis revealed that the film density of the IGZO:H decreased with an increase in R[H2] which would be the possible cause for facilitating the O diffusion at low temperature.
Abstract: Low-temperature activation of oxide semiconductor materials such as In-Ga-Zn-O (IGZO) is a key approach for their utilization in flexible devices. We previously reported that the activation temperature can be reduced to 150 °C by hydrogen-doped IGZO (IGZO:H), demonstrating a strong potential of this approach. In this paper, we investigated the mechanism for reducing the activation temperature of the IGZO:H films. In situ Hall measurements revealed that oxygen diffusion from annealing ambient into the conventional Ar/O2-sputtered IGZO film was observed at >240 °C. Moreover, the temperature at which the oxygen diffusion starts into the film significantly decreased to 100 °C for the IGZO:H film deposited at hydrogen gas flow ratio (R[H2]) of 8%. Hard X-ray photoelectron spectroscopy indicated that the near Fermi level (EF) defects in the IGZO:H film after the 150 °C annealing decreased in comparison to that in the conventional IGZO film after 300 °C annealing. The oxygen diffusion into the film during annealing plays an important role for reducing oxygen vacancies and subgap states especially for near EF. X-ray reflectometry analysis revealed that the film density of the IGZO:H decreased with an increase in R[H2] which would be the possible cause for facilitating the O diffusion at low temperature.
2 citations
TL;DR: In this article , the authors have demonstrated Cu2O TFTs with improved field-effect mobility and low off-current through reduction of cupric oxide (CuO) impurities and dissociative Cu defects with the combination of deposition and annealing conditions.
Abstract: Cuprous oxide (Cu2O) p-type thin-film transistors (TFTs) can be practically applied for complementary metal oxide semiconductor (CMOS) logic circuits, but the electrical performances are still insufficient due to high off-current and low field-effect mobility. Here, we have demonstrated Cu2O TFTs with improved field-effect mobility and low off-current through reduction of cupric oxide (CuO) impurities and dissociative Cu defects with the combination of deposition and annealing conditions. Copper oxide was deposited by radio frequency sputtering in mixed gases of argon and oxygen. After that, the deposited copper oxide was annealed at 800 °C in the tube furnace under a N2 atmosphere instead of a high vacuum condition. The fabricated Cu2O thin film had a high crystalline quality, the ratio of dissociative Cu defects decreased from 11.3 to 3.1%, and the electrical performances of the TFT including the fabricated Cu2O thin film exhibited the field-effect mobility of 1.11 ± 0.05 cm2/V·s, the on/off current ratio of 4.68 ± 0.8 × 104, and the subthreshold swing value of 3.91 ± 0.21 V dec–1. The fabricated Cu2O TFT showed a Vth shift of 3.31 V in the transfer curve under negative bias stress. Nitrogen plays a role in promoting Cu2O phase formation while it prevents CuO phase formation during the annealing process. In addition, oxygen added during sputtering increases the ratio of CuO in the copper oxide thin film and works effectively to reduce dissociative Cu defects in the annealing process. To determine the feasibility of the CMOS logic circuit, we also demonstrated the inverter with n-type indium–gallium–zinc oxide (IGZO) TFT and p-type Cu2O TFT, which showed a voltage gain of 14 at VDD = 20 V.
2 citations
TL;DR: In this article , a bilayer dielectric scheme combining aluminum oxide (AlOx) as a positive charge trapping insulator and yttrium aluminum oxide(YAl Ox) as negative charge trapping dielectrics was proposed to obtain hysteresis free switching in the solution-processed metal-oxide thin-film transistors.
Abstract: Solution processing and low-temperature annealing (T < 300°C) of the precursor compounds promise low-cost manufacturing for future applications of flexible oxide electronics. However, thermal budget reduction comes at the expense of increased charge trapping residuals in the dielectric layers, which result in hysteretic switching of transistors. This work reports on a novel bilayer dielectric scheme combining aluminum oxide (AlOx) as a positive charge trapping insulator and yttrium aluminum oxide (YAlOx) as a negative charge trapping dielectric to obtain hysteresis free switching in the solution-processed metal-oxide thin-film transistors. Devices were processed at a thermal budget of 250°C, without an encapsulation layer. The presence of H+ and OH− in the AlOx were found responsible for the hysteresis in the switching, which was suppressed successfully with the thickness optimization of the YAlOx in the dielectric stack. Fabricated devices yield ON/OFF ratios of 106, sub-pA level gate leakage currents, a subthreshold swing of 150 mV/decade, and field-effect mobility of 1.5 cm2/V-sec.
2 citations
01 Jan 2020
TL;DR: In this paper, the authors discuss the electrical performance of tin oxide-based materials and the importance of obtaining structures with well-defined electrical characteristics to be used in practical applications, such as smart and functional electronic and optoelectronic devices in both micro- and nanoscale.
Abstract: The understanding of electrical properties in engineered materials plays an essential role, whether for basic science or technological applications. The unique electrical/electronic features exhibited by semiconducting metal oxides (SMOx) make them fundamental building blocks for the design of smart and functional electronic and optoelectronic devices in both micro- and nanoscale. Tin oxide based-materials are outstanding representatives of SMOx that have received plenty of attention for decades due to their particular chemical and physical properties, especially SnO2, which is the most chemically and thermally stable oxidation state of tin oxide used in several areas. The growing interest for new stoichiometries of tin oxide, such as SnO and Sn3O4, has also arisen in recent years, but their electrical properties have not been detailed studied. This chapter is addressed to discuss the electrical performance of tin oxide-based materials and the importance of obtaining structures with well-defined electrical characteristics to be used in practical applications.
2 citations
TL;DR: In this article, a flexible monolithic integrated silicon RF low noise amplifier (LNA) on a plastic substrate is presented, which has a gain of ∼11 dB and a noise figure (NF) of ∼4.3 dB at 300 MHz.
Abstract: Flexible radio frequency (RF) circuits are highly desirable for flexible communication and other miniaturized function modules. However, the prevalent studies on flexible high-speed electronics have mostly focused on individual elements such as transistors, inductors, capacitors and transmission lines. Research on flexible RF monolithic integrated functional circuits is still limited. This letter presents the design of a flexible monolithic integrated silicon RF low noise amplifier (LNA) on plastic substrate. For the LNA, a flexible thin film transistor (TFT) based on a silicon nanomembrane, high-frequency flexible inductors and capacitors are fabricated and modeled. The impedance matching circuit on plastic substrate is analyzed and optimized. The LNA has a gain of ∼11 dB and a noise figure (NF) of ∼4.3 dB at 300 MHz. The influence of the parasitics induced by the flexible impedance matching on the gain and NF is discussed. This study provides useful design guideline for flexible RF monolithic integrated circuits and expands the high frequency applications of flexible electronics.
2 citations
References
More filters
TL;DR: A novel semiconducting material is proposed—namely, a transparent amorphous oxide semiconductor from the In-Ga-Zn-O system (a-IGZO)—for the active channel in transparent thin-film transistors (TTFTs), which are fabricated on polyethylene terephthalate sheets and exhibit saturation mobilities and device characteristics are stable during repetitive bending of the TTFT sheet.
Abstract: Transparent electronic devices formed on flexible substrates are expected to meet emerging technological demands where silicon-based electronics cannot provide a solution. Examples of active flexible applications include paper displays and wearable computers1. So far, mainly flexible devices based on hydrogenated amorphous silicon (a-Si:H)2,3,4,5 and organic semiconductors2,6,7,8,9,10 have been investigated. However, the performance of these devices has been insufficient for use as transistors in practical computers and current-driven organic light-emitting diode displays. Fabricating high-performance devices is challenging, owing to a trade-off between processing temperature and device performance. Here, we propose to solve this problem by using a novel semiconducting material—namely, a transparent amorphous oxide semiconductor from the In-Ga-Zn-O system (a-IGZO)—for the active channel in transparent thin-film transistors (TTFTs). The a-IGZO is deposited on polyethylene terephthalate at room temperature and exhibits Hall effect mobilities exceeding 10 cm2 V-1 s-1, which is an order of magnitude larger than for hydrogenated amorphous silicon. TTFTs fabricated on polyethylene terephthalate sheets exhibit saturation mobilities of 6–9 cm2 V-1 s-1, and device characteristics are stable during repetitive bending of the TTFT sheet.
7,301 citations
Book•
04 Jul 1990
TL;DR: In this article, the authors present a characterization of the resistivity of a two-point-versus-four-point probe in terms of the number of contacts and the amount of contacts in the probe.
Abstract: Preface to Third Edition. 1 Resistivity. 1.1 Introduction. 1.2 Two-Point Versus Four-Point Probe. 1.3 Wafer Mapping. 1.4 Resistivity Profiling. 1.5 Contactless Methods. 1.6 Conductivity Type. 1.7 Strengths and Weaknesses. Appendix 1.1 Resistivity as a Function of Doping Density. Appendix 1.2 Intrinsic Carrier Density. References. Problems. Review Questions. 2 Carrier and Doping Density. 2.1 Introduction. 2.2 Capacitance-Voltage (C-V). 2.3 Current-Voltage (I-V). 2.4 Measurement Errors and Precautions. 2.5 Hall Effect. 2.6 Optical Techniques. 2.7 Secondary Ion Mass Spectrometry (SIMS). 2.8 Rutherford Backscattering (RBS). 2.9 Lateral Profiling. 2.10 Strengths and Weaknesses. Appendix 2.1 Parallel or Series Connection? Appendix 2.2 Circuit Conversion. References. Problems. Review Questions. 3 Contact Resistance and Schottky Barriers. 3.1 Introduction. 3.2 Metal-Semiconductor Contacts. 3.3 Contact Resistance. 3.4 Measurement Techniques. 3.5 Schottky Barrier Height. 3.6 Comparison of Methods. 3.7 Strengths and Weaknesses. Appendix 3.1 Effect of Parasitic Resistance. Appendix 3.2 Alloys for Contacts to Semiconductors. References. Problems. Review Questions. 4 Series Resistance, Channel Length and Width, and Threshold Voltage. 4.1 Introduction. 4.2 PN Junction Diodes. 4.3 Schottky Barrier Diodes. 4.4 Solar Cells. 4.5 Bipolar Junction Transistors. 4.6 MOSFETS. 4.7 MESFETS and MODFETS. 4.8 Threshold Voltage. 4.9 Pseudo MOSFET. 4.10 Strengths and Weaknesses. Appendix 4.1 Schottky Diode Current-Voltage Equation. References. Problems. Review Questions. 5 Defects. 5.1 Introduction. 5.2 Generation-Recombination Statistics. 5.3 Capacitance Measurements. 5.4 Current Measurements. 5.5 Charge Measurements. 5.6 Deep-Level Transient Spectroscopy (DLTS). 5.7 Thermally Stimulated Capacitance and Current. 5.8 Positron Annihilation Spectroscopy (PAS). 5.9 Strengths and Weaknesses. Appendix 5.1 Activation Energy and Capture Cross-Section. Appendix 5.2 Time Constant Extraction. Appendix 5.3 Si and GaAs Data. References. Problems. Review Questions. 6 Oxide and Interface Trapped Charges, Oxide Thickness. 6.1 Introduction. 6.2 Fixed, Oxide Trapped, and Mobile Oxide Charge. 6.3 Interface Trapped Charge. 6.4 Oxide Thickness. 6.5 Strengths and Weaknesses. Appendix 6.1 Capacitance Measurement Techniques. Appendix 6.2 Effect of Chuck Capacitance and Leakage Current. References. Problems. Review Questions. 7 Carrier Lifetimes. 7.1 Introduction. 7.2 Recombination Lifetime/Surface Recombination Velocity. 7.3 Generation Lifetime/Surface Generation Velocity. 7.4 Recombination Lifetime-Optical Measurements. 7.5 Recombination Lifetime-Electrical Measurements. 7.6 Generation Lifetime-Electrical Measurements. 7.7 Strengths and Weaknesses. Appendix 7.1 Optical Excitation. Appendix 7.2 Electrical Excitation. References. Problems. Review Questions. 8 Mobility. 8.1 Introduction. 8.2 Conductivity Mobility. 8.3 Hall Effect and Mobility. 8.4 Magnetoresistance Mobility. 8.5 Time-of-Flight Drift Mobility. 8.6 MOSFET Mobility. 8.7 Contactless Mobility. 8.8 Strengths and Weaknesses. Appendix 8.1 Semiconductor Bulk Mobilities. Appendix 8.2 Semiconductor Surface Mobilities. Appendix 8.3 Effect of Channel Frequency Response. Appendix 8.4 Effect of Interface Trapped Charge. References. Problems. Review Questions. 9 Charge-based and Probe Characterization. 9.1 Introduction. 9.2 Background. 9.3 Surface Charging. 9.4 The Kelvin Probe. 9.5 Applications. 9.6 Scanning Probe Microscopy (SPM). 9.7 Strengths and Weaknesses. References. Problems. Review Questions. 10 Optical Characterization. 10.1 Introduction. 10.2 Optical Microscopy. 10.3 Ellipsometry. 10.4 Transmission. 10.5 Reflection. 10.6 Light Scattering. 10.7 Modulation Spectroscopy. 10.8 Line Width. 10.9 Photoluminescence (PL). 10.10 Raman Spectroscopy. 10.11 Strengths and Weaknesses. Appendix 10.1 Transmission Equations. Appendix 10.2 Absorption Coefficients and Refractive Indices for Selected Semiconductors. References. Problems. Review Questions. 11 Chemical and Physical Characterization. 11.1 Introduction. 11.2 Electron Beam Techniques. 11.3 Ion Beam Techniques. 11.4 X-Ray and Gamma-Ray Techniques. 11.5 Strengths and Weaknesses. Appendix 11.1 Selected Features of Some Analytical Techniques. References. Problems. Review Questions. 12 Reliability and Failure Analysis. 12.1 Introduction. 12.2 Failure Times and Acceleration Factors. 12.3 Distribution Functions. 12.4 Reliability Concerns. 12.5 Failure Analysis Characterization Techniques. 12.6 Strengths and Weaknesses. Appendix 12.1 Gate Currents. References. Problems. Review Questions. Appendix 1 List of Symbols. Appendix 2 Abbreviations and Acronyms. Index.
6,573 citations
TL;DR: In this paper, a review of the literature in the area of alternate gate dielectrics is given, based on reported results and fundamental considerations, the pseudobinary materials systems offer large flexibility and show the most promise toward success.
Abstract: Many materials systems are currently under consideration as potential replacements for SiO2 as the gate dielectric material for sub-0.1 μm complementary metal–oxide–semiconductor (CMOS) technology. A systematic consideration of the required properties of gate dielectrics indicates that the key guidelines for selecting an alternative gate dielectric are (a) permittivity, band gap, and band alignment to silicon, (b) thermodynamic stability, (c) film morphology, (d) interface quality, (e) compatibility with the current or expected materials to be used in processing for CMOS devices, (f) process compatibility, and (g) reliability. Many dielectrics appear favorable in some of these areas, but very few materials are promising with respect to all of these guidelines. A review of current work and literature in the area of alternate gate dielectrics is given. Based on reported results and fundamental considerations, the pseudobinary materials systems offer large flexibility and show the most promise toward success...
5,711 citations
IBM1
TL;DR: In this article, the authors present new insight into conduction mechanisms and performance characteristics, as well as opportunities for modeling properties of organic thin-film transistors (OTFTs) and discuss progress in the growing field of n-type OTFTs.
Abstract: Organic thin-film transistors (OTFTs) have lived to see great improvements in recent years. This review presents new insight into conduction mechanisms and performance characteristics, as well as opportunities for modeling properties of OTFTs. The shifted focus in research from novel chemical structures to fabrication technologies that optimize morphology and structural order is underscored by chapters on vacuum-deposited and solution-processed organic semiconducting films. Finally, progress in the growing field of the n-type OTFTs is discussed in ample detail. The Figure, showing a pentacene film edge on SiO2, illustrates the morphology issue.
4,804 citations
TL;DR: An outlook is presented on what will be required to drive this young photovoltaic technology towards the next major milestone, a 10% power conversion efficiency, considered by many to represent the efficiency at which OPV can be adopted in wide-spread applications.
Abstract: Solution-processed bulk-heterojunction solar cells have gained serious attention during the last few years and are becoming established as one of the future photovoltaic technologies for low-cost power production. This article reviews the highlights of the last few years, and summarizes today's state-of-the-art performance. An outlook is given on relevant future materials and technologies that have the potential to guide this young photovoltaic technology towards the magic 10% regime. A cost model supplements the technical discussions, with practical aspects any photovoltaic technology needs to fulfil, and answers to the question as to whether low module costs can compensate lower lifetimes and performances.
3,084 citations