The Influence of 3D Printing Parameters on Adhesion between Polylactic Acid (PLA) and Thermoplastic Polyurethane (TPU).
TL;DR: In this paper, the authors presented the possibility of printing with PLA and TPU using commercially available filaments and software to obtain the best possible bond strength between two different polymers with respect to printing parameters, surface pattern, and the order of layer application.
Abstract: A 3D printer in FDM technology allows printing with two nozzles, which creates an opportunity to produce multi-material elements. Printing from two materials requires special consideration of the interface zone generated between their geometrical boundaries. This article aims to present the possibility of printing with PLA and TPU using commercially available filaments and software to obtain the best possible bond strength between two different polymers with respect to printing parameters, surface pattern (due to the material contact surface’s roughness), and the order of layer application. The interaction at the interface of two surfaces of two different filaments (PLA-TPU and TPU-PLA) and six combinations of patterns were tested by printing seven replicas for each. A total of 12 combinations were obtained. By analyzing pairs of samples (the same patterns, different order of materials), the results for the TPU/PLA samples were better or very close to the results for PLA/TPU. The best variants of pattern combinations were distinguished. Well-chosen printing parameters can prevent a drop in parts efficiency compared to component materials (depending on the materials combination).
Citations
More filters
TL;DR: In this article , the authors present the material properties of conductive PLA material, which is capable of conducting electric current, and describe the design of the experiment, the process of measuring the resistance of samples printed by FDM device, measuring the maximum tensile strength of samples.
Abstract: There is a large number of materials that can be used for FDM additive manufacturing technology. These materials have different strength properties, they are designed for different purposes. They can be highly strong or flexible, abrasion-resistant, or designed for example for environments with higher thermal loads. However recently new innovative and progressive materials have come to the practice, which include nano-composite particles, bringing new added value. One such material is the Conductive PLA material, which is capable of conducting electric current. The aim of this article is to present the material properties of this material. The article describes the design of the experiment, the process of measuring the resistance of samples printed by FDM device, measuring the maximum tensile strength of samples. The article includes a statistical evaluation of the measured data, with the determination of the significance of individual factors of the experiment as well as the evaluation of the overall result of the experiments.
16 citations
TL;DR: In this article , the authors presented the LOM manufacturing of 3D-printed flexural specimens of two widely used polymers available viz. ABS and TPU and tested as per ASTM D790 standards.
Abstract: Fused deposition modeling (FDM) printing of commercial and reinforced filaments is a proven and well-explored method for the enhancement of mechanical properties. However, little has hitherto been reported on the multi-material components, fused or laminated together into a single specimen by using the laminated object manufacturing (LOM) technique for sustainable/renewable polymers. TPU is one such durable and flexible, sustainable material exhibiting renewable and biocompatible properties that have been explored very less often in combination with the ABS polymer matrix in a single specimen, such as the LOM specimen. The current research work presents the LOM manufacturing of 3D-printed flexural specimens of two different, widely used polymers available viz. ABS and TPU and tested as per ASTM D790 standards. The specimens were made and laminated in three layers. They were grouped into two categories, namely ABS: TPU: ABS (ATA) and TPU: ABS: TPU (TAT), which are functionally graded, sandwiched structures of polymeric material. The investigation of the flexural properties, microscopic imaging, and porosity characteristics of the specimens was made for the above categories. The results of the study suggest that ATA-based samples held larger flexural strength than TAT laminated manufactured samples. A significant improvement in the peak elongation and break elongation of the samples was achieved and has shown a 187% increase in the break elongation. Similarly, for the TAT-based specimen, flexural strength was improved significantly from approximately 6.8 MPa to 13 MPa, which represents a nearly 92% increase in the flexural strength. The morphological testing using Tool Maker’s microscopic analysis and porosity analysis has supported the observed trends of mechanical behavior of ATA and TAT samples.
9 citations
5 citations
TL;DR: In this article , the authors focused on obtaining the ideal weight-to-performance ratio for making a 3D-printed part and analyzed the effect of infill density, wall perimeter and layer height on tensile elasticity of the part.
Abstract: Three-dimensional printing is widely used in many fields, including engineering, architecture and even medical purposes. The focus of the study is to obtain the ideal weight-to-performance ratio for making a 3D-printed part. The end products of the 3D-printed part are hugely affected by not only the material but also the printing parameters. The printing parameters to be highlighted for this study are the infill density, wall perimeter and layer height, which are the commonly adjusted parameters in 3D printing. The study will be divided into two parts, the simulation analysis and the experimental analysis, to confirm both results toward the trend of Young’s modulus for the material. It will then be analyzed and discussed toward any differences between the two results. The results showed that increasing the value of all three parameters will increase the tensile elasticity of the part.
3 citations
TL;DR: In this article , the authors focus on the thermo-formability and shape recovery characteristics of 3D-printed multi-material specimens under different thermoforming temperatures, where the specimens were then reheated at 60 °C to evaluate their shape memory ability.
Abstract: Multi-material products are required in fused deposition modelling (FDM) to meet a desired specification such as a rigid structure with soft material for impact protection. This paper focuses on the thermoformability and shape recovery characteristics of three-dimensional (3D)-printed multi-material specimens under different thermoforming temperatures. The multi-material specimens consist of polylactic acid (PLA) and thermoplastic polyurethane (TPU). The PLA/TPU specimens were prepared by depositing the TPU component on top of the PLA component using a fused deposition modelling (FDM) machine. Simple thermoforming tests were proposed, where the specimens were bent under load and molded into a circular shape at different thermoforming temperatures. The bent specimens were then reheated at 60 °C to evaluate their shape memory ability. The test results were quantified into apparent bending modulus and shape recovery percentage. The PLA/TPU specimens showed a better apparent bending modulus of 143 MPa than a PLA specimen at a temperature between 60 °C to 90 °C. However, only the PLA/TPU specimens being thermoformed into a circular shape at 100 °C or greater showed good shape retention accuracy and interfacial surface bonding. The PLA/TPU specimens that were thermoformed at 60 °C to 90 °C showed reasonable shape memory of about 60% recovery when reheated. Finally, suitable thermoforming temperatures for thermoforming PLA/TPU specimens were suggested based on design needs.
2 citations
References
More filters
TL;DR: In this paper, the influence of process parameters on the quality characteristics of the prototypes using Taguchi technique has been assessed and the results of the study and the conclusions arrived from it.
655 citations
TL;DR: In this paper, a high-resolution projection microstereolithography (PμSL) approach is used to create high resolution (up to a few microns), multimaterial shape memory polymer (SMP) architectures.
Abstract: We present a new 4D printing approach that can create high resolution (up to a few microns), multimaterial shape memory polymer (SMP) architectures. The approach is based on high resolution projection microstereolithography (PμSL) and uses a family of photo-curable methacrylate based copolymer networks. We designed the constituents and compositions to exhibit desired thermomechanical behavior (including rubbery modulus, glass transition temperature and failure strain which is more than 300% and larger than any existing printable materials) to enable controlled shape memory behavior. We used a high resolution, high contrast digital micro display to ensure high resolution of photo-curing methacrylate based SMPs that requires higher exposure energy than more common acrylate based polymers. An automated material exchange process enables the manufacture of 3D composite architectures from multiple photo-curable SMPs. In order to understand the behavior of the 3D composite microarchitectures, we carry out high fidelity computational simulations of their complex nonlinear, time-dependent behavior and study important design considerations including local deformation, shape fixity and free recovery rate. Simulations are in good agreement with experiments for a series of single and multimaterial components and can be used to facilitate the design of SMP 3D structures.
650 citations
TL;DR: The MM3D printheads exploit the diode-like behaviour that arises when multiple viscoelastic materials converge at a junction to enable seamless, high-frequency switching between up to eight different materials to create voxels with a volume approaching that of the nozzle diameter cubed, substantially broadens the palette of voxelated materials that can be designed and manufactured in complex motifs.
Abstract: There is growing interest in voxelated matter that is designed and fabricated voxel by voxel1–4. Currently, inkjet-based three-dimensional (3D) printing is the only widely adopted method that is capable of creating 3D voxelated materials with high precision1–4, but the physics of droplet formation requires the use of low-viscosity inks to ensure successful printing5. By contrast, direct ink writing, an extrusion-based 3D printing method, is capable of patterning a much broader range of materials6–13. However, it is difficult to generate multimaterial voxelated matter by extruding monolithic cylindrical filaments in a layer-by-layer manner. Here we report the design and fabrication of voxelated soft matter using multimaterial multinozzle 3D (MM3D) printing, in which the composition, function and structure of the materials are programmed at the voxel scale. Our MM3D printheads exploit the diode-like behaviour that arises when multiple viscoelastic materials converge at a junction to enable seamless, high-frequency switching between up to eight different materials to create voxels with a volume approaching that of the nozzle diameter cubed. As exemplars, we fabricate a Miura origami pattern14 and a millipede-like soft robot that locomotes by co-printing multiple epoxy and silicone elastomer inks of stiffness varying by several orders of magnitude. Our method substantially broadens the palette of voxelated materials that can be designed and manufactured in complex motifs. Voxelated soft matter is designed and fabricated using multimaterial multinozzle three-dimensional printing, which switches between different viscoelastic inks along the same print filament to print multiple materials simultaneously.
564 citations
TL;DR: In this paper, the most significant process parameters considered as influencing FDM specimens' tensile, compression, flexural or impact strengths are discussed considering the results presented in the literature, and a necessary distinction between the mechanical properties of material and testing specimens and the mechanical behavior of a FDM end part is also made.
549 citations
TL;DR: In this article, a new approach to model surface roughness in fused deposition modeling (FDM) is proposed, which is based on real-world FDM parts and a theoretical model is presented by considering the main factors that crucially affect surface quality.
357 citations