Thermal transport properties of carbon-assisted phase change nanocomposite
01 Jul 2020-Fullerenes Nanotubes and Carbon Nanostructures (Taylor & Francis)-Vol. 28, Iss: 11, pp 925-933
TL;DR: In this article, stability, density, rheology, and thermal conductivity of the Multi-wall carbon nanotubes (MWCNTs) based PCM nanocomposites were experimentally investigated.
Abstract: In this study, stability, density, rheology, and thermal conductivity of the Multi-wall carbon nanotubes (MWCNTs) based PCM nanocomposites were experimentally investigated. The PCM OM08 has been se...
Citations
More filters
01 Jan 2005
TL;DR: In this paper, the problem of laminar forced convection flow of nanofluids has been thoroughly investigated for two particular geometrical configurations, namely a uniformly heated tube and a system of parallel, coaxial and heated disks.
Abstract: The problem of laminar forced convection flow of nanofluids has been thoroughly investigated for two particular geometrical configurations, namely a uniformly heated tube and a system of parallel, coaxial and heated disks. Numerical results, as obtained for water-γAl 2 O 3 and Ethylene Glycol-γAl 2 O 3 mixtures, have clearly shown that the inclusion of nanoparticles into the base fluids has produced a considerable augmentation of the heat transfer coefficient that clearly increases with an increase of the particle concentration. However, the presence of such particles has also induced drastic effects on the wall shear stress that increases appreciably with the particle loading. Among the mixtures studied, the Ethylene Glycol -γAl 2 O 3 nanofluid appears to offer a better heat transfer enhancement than water- γ/Al 2 O 3 ; it is also the one that has induced more pronounced adverse effects on the wall shear stress. For the case of tube flow, results have also shown that, in general, the heat transfer enhancement also increases considerably with an augmentation of the flow Reynolds number. Correlations have been provided for computing the Nusselt number for the nanofluids considered in terms of the Reynolds and the Prandtl numbers and this for both the thermal boundary conditions considered
93 citations
TL;DR: In this article, a novel nanofluid using Therminol-55 (T-55) as heat transfer fluid and multi-wall carbon nanotubes (MWCNTs) as dispersants with various volume concentrations of 0.05, 0.3, and 0.5% and assess its thermo-physical properties for solar-thermal applications.
Abstract: This work aims to develop a novel nanofluid using Therminol-55 (T-55) as heat transfer fluid and multi-wall carbon nanotubes (MWCNTs) as dispersants with various volume concentrations of 0.05, 0.1, 0.3, and 0.5% and assess its thermo-physical properties for solar-thermal applications. The pH values of nanofluid MWCNT/T-55 with various particle loading were too far-flung from the pH (I) value, which confirmed the good dispersion stability of nanofluid. The measured density shows tremendous deviation from predicted density with increasing MWCNT loading owing to the non-considering of microstructural parameters in Pak & Cho correlation predication. The highest augmentation in nanofluid thermal conductivity was 16.83% for 0.5 vol. % MWCNT at 60 °C. The maximum improvement in dynamic viscosity of nanofluid with 0.5 vol. % of MWCNT is found to be 44%, and this rise is reduced at higher temperatures. The thermal effectiveness of the nanofluids demonstrates that nanofluid with all volume fractions of MWCNTs was favorable at higher temperatures in the laminar region. Mouromtseff number ratio decreases with a rise in temperature and MWCNT volume concentration. It is concluded that the excellent thermo-physical properties and prolonged thermal stability of the MWCNT will be highly beneficial in improving the overall performance of various kinds of heat transfer fluids (HTFs) for process heating and solar-thermal applications.
14 citations
TL;DR: In this paper, the authors investigated the thermophysical properties of binary eutectic PCM salt (LiNO3+NaCl) using the dispersion of multi-walled carbon nanotubes (MWCNTs) with varying weight fractions.
Abstract: In this article, the thermophysical properties of binary eutectic PCM salt (LiNO3 + NaCl) are investigated experimentally using the dispersion of multi-walled carbon nanotubes (MWCNTs) with varying weight fractions (i.e., 0.25 %, 0.5 %, and 1 %). According to the XRD and FTIR results, MWCNTs physically amalgamated with base eutectic salt without affecting their chemical structure. The Kissinger model is used to assess the phase change kinetics of the prepared nano-PCM composites. With the addition of MWCNTs, the activation energy of the chosen PCM is significantly increased. The thermophysical properties of the nano-PCM samples, such as phase transition temperature and latent heat value, are measured using differential scanning calorimetry (DSC) and thermal conductivity using a laser flash apparatus. The results show that dispersing 1 % MWCNTs in PCM salt improved the thermal conductivity enhancement ratio by 38.59 %, while decreasing the latent heat storage capacity by 14.98 %. Furthermore, by training the experimental DSC values of nano-PCM samples at various heating rates, an artificial neural network is developed to predict the thermophysical properties of nanocomposites. With an R2 value of 0.998, the developed neural network accurately predicted the experimental DSC values.
14 citations
TL;DR: In this paper , the performance of the low-capacity energy storage tank in different heat transfer fluid (HTF) conditions (at various flow rates) filled with spherical capsules containing nano-enhanced phase change material (nano-PCM) was investigated.
12 citations
TL;DR: In this article, an attempt was made to extend the comfort of a passenger car cabin during the compressor off cycle using thermal energy storage (TES) in an HFO-1234yf mobile air conditioning (MAC) unit for idle stop/start vehicles.
Abstract: In this study, an attempt was made to extend the comfort of a passenger car cabin during the compressor off cycle using thermal energy storage (TES) in an HFO-1234yf mobile air conditioning (MAC) unit for idle stop/start vehicles. Fatty acid (OM08), as a phase change material (PCM), with 0.1–0.5 vol% of graphene nanoplatelets (GnPs) was used in this study. It was found that the inclusion of GnPs increases the thermal conductivity and dynamic viscosity of the liquid PCM nanocomposites by ~ 46% and ~ 53%, respectively, with 0.5 vol% of GnPs. During the pull-down cycle, the enhanced thermal conductivity outweighs the increased dynamic viscosity, resulting in a quicker decrease in PCM temperature. The test results revealed that the cabin temperature increases through the addition of TES, with a marginal decrease in the coefficient of performance. The addition of TES with the use of pure PCM increases the compressor power consumption of the MAC system by less than 1%. However, with the inclusion of graphene the power consumption increases with respect to the volume fraction. Without TES, the cabin comfort is extended by 78 s, 60 s, and 43 s for heating loads of 500, 1000, and 1500 W, respectively, and with the inclusion of TES, using pure PCM, the cabin comfort increased by up to 106 s, 87 s, and 63 s, respectively. The inclusion of 0.5 vol% GnPs extends the cabin comfort further by up to 189 s, 147 s, and 105 s for heating loads of 500, 1000, and 1500 W, respectively. Further, the CO2 equivalent emissions of the MAC system with TES using a pure PCM and a PCM nanocomposite are 10.54% and 5.64% lower than that of the system without TES, respectively.
11 citations
References
More filters
TL;DR: In this article, the authors considered seven slip mechanisms that can produce a relative velocity between the nanoparticles and the base fluid and concluded that only Brownian diffusion and thermophoresis are important slip mechanisms in nanofluids.
Abstract: Nanofluids are engineered colloids made of a base fluid and nanoparticles (1-100 nm) Nanofluids have higher thermal conductivity' and single-phase heat transfer coefficients than their base fluids In particular the heat transfer coefficient increases appear to go beyond the mere thermal-conductivity effect, and cannot be predicted by traditional pure-fluid correlations such as Dittus-Boelter's In the nanofluid literature this behavior is generally attributed to thermal dispersion and intensified turbulence, brought about by nanoparticle motion To test the validity of this assumption, we have considered seven slip mechanisms that can produce a relative velocity between the nanoparticles and the base fluid These are inertia, Brownian diffusion, thermophoresis, diffusioplwresis, Magnus effect, fluid drainage, and gravity We concluded that, of these seven, only Brownian diffusion and thermophoresis are important slip mechanisms in nanofluids Based on this finding, we developed a two-component four-equation nonhomogeneous equilibrium model for mass, momentum, and heat transport in nanofluids A nondimensional analysis of the equations suggests that energy transfer by nanoparticle dispersion is negligible, and thus cannot explain the abnormal heat transfer coefficient increases Furthermore, a comparison of the nanoparticle and turbulent eddy time and length scales clearly indicates that the nanoparticles move homogeneously with the fluid in the presence of turbulent eddies so an effect on turbulence intensity is also doubtful Thus, we propose an alternative explanation for the abnormal heat transfer coefficient increases: the nanofluid properties may vary significantly within the boundary layer because of the effect of the temperature gradient and thermophoresis For a heated fluid, these effects can result in a significant decrease of viscosity within the boundary layer, thus leading to heat transfer enhancement A correlation structure that captures these effects is proposed
5,329 citations
TL;DR: In this article, the authors used a Brookfield rotating viscometer to measure the viscosities of the dispersed fluids with γ-alumina (Al2O3) and titanium dioxide (TiO2) particles at a 10% volume concentration.
Abstract: Turbulent friction and heat transfer behaviors of dispersed fluids (i.e., uttrafine metallic oxide particles suspended in water) in a circular pipe were investigated experimentally. Viscosity measurements were also conducted using a Brookfield rotating viscometer. Two different metallic oxide particles, γ-alumina (Al2O3) and titanium dioxide (TiO2), with mean diameters of 13 and 27 nm, respectively, were used as suspended particles. The Reynolds and Prandtl numbers varied in the ranges l04-I05 and 6.5-12.3, respectively. The viscosities of the dispersed fluids with γ-Al2O3 and TiO2 particles at a 10% volume concentration were approximately 200 and 3 times greater than that of water, respectively. These viscosity results were significantly larger than the predictions from the classical theory of suspension rheology. Darcy friction factors for the dispersed fluids of the volume concentration ranging from 1% to 3% coincided well with Kays' correlation for turbulent flow of a single-phase fluid. The Nusselt n...
3,730 citations
TL;DR: In this paper, an expression for the viscosity of solutions and suspensions of finite concentration is derived by considering the effect of the addition of one solute-molecule to an existing solution, which is considered as a continuous medium.
Abstract: An expression for the viscosity of solutions and suspensions of finite concentration is derived by considering the effect of the addition of one solute‐molecule to an existing solution, which is considered as a continuous medium.
3,724 citations
TL;DR: In this article, the effect of Brownian motion on the probability density of the separation vector of rigid spherical particles in a dilute suspension is investigated and an explicit expression for this leading approximation is constructed in terms of hydrodynamic interactions between pairs of particles.
Abstract: The effect of Brownian motion of particles in a statistically homogeneous suspension is to tend to make uniform the joint probability density functions for the relative positions of particles, in opposition to the tendency of a deforming motion of the suspension to make some particle configurations more common. This smoothing process of Brownian motion can be represented by the action of coupled or interactive steady ‘thermodynamic’ forces on the particles, which have two effects relevant to the bulk stress in the suspension. Firstly, the system of thermodynamic forces on particles makes a direct contribution to the bulk stress; and, secondly, thermodynamic forces change the statistical properties of the relative positions of particles and so affect the bulk stress indirectly. These two effects are analysed for a suspension of rigid spherical particles. In the case of a dilute suspension both the direct and indirect contributions to the bulk stress due to Brownian motion are of order o2, where o([Lt ] 1) is the volume fraction of the particles, and an explicit expression for this leading approximation is constructed in terms of hydrodynamic interactions between pairs of particles. The differential equation representing the effects of the bulk deforming motion and the Brownian motion on the probability density of the separation vector of particle pairs in a dilute suspension is also investigated, and is solved numerically for the case of relatively strong Brownian motion. The suspension has approximately isotropic structure in this case, regardless of the nature of the bulk flow, and the effective viscosity representing the stress system to order ϕ2 is found to be
\[
\mu^{*} = \mu(1+2.5\phi + 6.2\phi^2).
\]
The value of the coefficient of o2 for steady pure straining motion in the case of weak Brownian motion is known to be 7[sdot ]6, which indicates a small degree of ‘strain thickening’ in the o2-term.
1,956 citations
TL;DR: In this article, the problem of laminar forced convection flow of nanofluids has been thoroughly investigated for two particular geometrical configurations, namely a uniformly heated tube and a system of parallel, coaxial and heated disks.
929 citations