UHF technique for identification of discharges initiated by liquid droplet in epoxy nanocomposite insulation material under ac voltages
TL;DR: In this article, the feasibility of using a ultra-high frequency (UHF) technique for identification of any corona discharge/arcing in insulating material due to water droplets was made.
Abstract: In this work, an attempt has been made to understand the feasibility of using a ultrahigh frequency (UHF) technique for identification of any corona discharge/ arcing in insulating material due to water droplets. The sensors of broadband type are useful for the identification of such discharges. It is realized that corona discharges/arcing initiated by liquid droplet radiates UHF signals in the entire bandwidth up to 2 GHz. The frequency content of the UHF signal generated due to corona/arcing is not much varied in epoxy nanocomposites with different weight percentage of clay content. The exfoliated/intercalated properties were analysed through TEM studies. It is realized that corona initiated discharges are of intermittent process. It is observed that the permittivity and tan(δ) reduces with increase in percentage of clay in epoxy nanocomposite material up to 3 wt%. The hydrophobicity of the material is characterized through contact angle measurement. It is realized that low weight percentage of nanoclay content in epoxy resin reduces the surface carbonization due to arcing.
Citations
More filters
TL;DR: The droplet coalescence, the discharge activity and the surface thermal distribution response between sessile multidroplets and chloride salt droplets under high tangential electric fields have been investigated with infrared thermography, high-speed photography and pulse current measurement.
Abstract: Understanding the interaction behaviors between sessile droplets under imposed high voltages is very important in many practical situations, e.g., microfluidic devices and the degradation/aging problems of outdoor high-power applications. In the present work, the droplet coalescence, the discharge activity and the surface thermal distribution response between sessile multidroplets and chloride salt droplets under high tangential electric fields have been investigated with infrared thermography, high-speed photography and pulse current measurement. Obvious polarity effects on the discharge path direction and the temperature change in the droplets in the initial stage after discharge initiation were observed due to the anodic dissolution of metal ions from the electrode. In the case of sessile aligned multidroplets, the discharge path direction could affect the location of initial droplet coalescence. The smaller unmerged droplet would be drained into the merged large droplet as a result from the pressure difference inside the droplets rather than the asymmetric temperature change due to discharge. The discharge inception voltages and the temperature variations for two salt droplets closely correlated with the ionization degree of the salt, as well as the interfacial electrochemical reactions near the electrodes. Mechanisms of these observed phenomena were discussed.
26 citations
TL;DR: In this paper, the authors used laser induced breakdown spectroscopy (LIBS) technique for characterisation of samples and measured threshold fluence and plasma temperatures through LIBS studies to classify the ageing condition of the composite material.
Abstract: Corona ageing of the epoxy nanocomposites surface exhibits a high influence on contact angle of the material. A reduction in corona inception voltage due to water droplet, upon corona ageing, is less with epoxy composites, which has Wollastonite as filler followed with nano-micro silica filler added epoxy composites. Charge accumulation studies indicate that charge retention time drastically reduces with corona aged epoxy composite specimen. Epoxy composites with Wollastonite as filler have shown higher mean charge lifetime. Adoption of laser induced breakdown spectroscopy (LIBS) technique for characterisation of samples is unique. Measure of threshold fluence and plasma temperatures through LIBS studies enables to classify the ageing condition of the composite material. Plasma temperature and threshold fluence are clear indicators to classify different materials. Plasma temperature is also an indicator of the hardness of the material. Epoxy composite with Wollastonite as filler is not affected by laser abrasion, which is in accordance with its superior performance with corona ageing, proving as discharge resistant material.
19 citations
TL;DR: In this paper, it was found that an increase in droplet volume and number of droplets within the gap reduces the CIV and the magnitude of discharge current flow is high under negative polarity.
Abstract: Epoxy nanocomposites with different percentages of nano clay filler are prepared using a shear mixer technique. Corona inception voltage (CIV) due to water droplets on the epoxy nanocomposite is high under negative direct voltage compared with positive polarity voltage. It was found that an increase in droplet volume and number of droplets within the gap reduces the CIV. The magnitude of discharge current flow is high under negative polarity. Surface charge accumulation studies indicate nonlinear variation in distribution of charges on the surface of the epoxy nanocomposite with water droplets. Optical Emission Spectroscopy (OES) results confirm high temperature plasma during water droplet initiated electrical discharges on the surface of epoxy resin. Laser Induced Breakdown Spectroscopy (LIBS) results indicate the presence of carbon on the degraded surface of the sample. The absorbed energy on the sample surface during arcing is measured through leakage current, and is observed to be higher for negative polarity. UHF signals were radiated due to corona discharges from water droplets on the epoxy nanocomposites under direct voltages and their bandwidth is in the range of 1–2 GHz.
12 citations
TL;DR: In this article, the thermal characteristics in the interaction process between water droplets on a hydrophobic insulator surface under high direct current voltages have been investigated with the infrared thermography.
Abstract: The thermal characteristics in the interaction process between water droplets on a hydrophobic insulator surface under high direct current voltages have been investigated with the infrared thermography. Discharge inception under a sufficiently high electric field resulted in the temperature rise between droplets and the formation of a liquid channel. The channel was transient for low conductivity droplets followed by their coalescence while stable for highly conductive ones. Asymmetric temperature distributions in the associated droplets appeared, and localized drying in the low conductivity droplet near the higher potential electrode initiated intermittent discharge. Mechanisms of these experimental phenomena have been discussed.
11 citations
TL;DR: In this article, the impact of high-frequency AC voltage and the percentage of ripple content in DC voltage on corona inception caused by water droplets was analyzed and the surface potential characteristics were altered with corona-aged specimen.
Abstract: The study of epoxy nano micro composites clearly indicates that the material has better dielectric properties with a good discharge resistance and less surface charge accumulation on its surface. The impact of high-frequency AC voltage and the percentage of ripple content in DC voltage on corona inception caused by water droplets was analyzed. Under a high frequency, the variation in the shape of the water droplet is the same as that under 50 Hz AC voltage. The UHF signal radiated due to water droplet initiated discharges have signal bandwidth in the range of 300 MHz-3 GHz. The influence of corona discharge on surface properties of the material, its variation to contact angle and water droplet initiated corona activity under AC voltage was analyzed. The surface potential characteristics were altered with corona-aged specimen. The impact of an ion-trapping particle on nanocomposites clearly exhibits its characteristics through surface potential studies. Water diffusion into the insulating materials varies with the type of filler material. The temperatures measured during arcing, analyzed through laser-induced breakdown spectroscopy (LIBS), were correlated with the hardness of the material. In addition, the mechanical properties, especially storage modulus and tan δ, were analyzed through dynamic mechanical analysis (DMA) studies.
10 citations
Cites background from "UHF technique for identification of..."
...studied the effect of corona inception voltage (CIV) caused by water droplet initiated discharge on the surface of the insulating material, and indicated that the water droplet initiated discharges radiate UHF signals [7]....
[...]
References
More filters
TL;DR: In this article, a review of polymer-layered silicate nanocomposites is presented, where the polymer chains are sandwiched in between silicate layers and exfoliated layers are more or less uniformly dispersed in the polymer matrix.
Abstract: This review aims at reporting on very recent developments in syntheses, properties and (future) applications of polymer-layered silicate nanocomposites. This new type of materials, based on smectite clays usually rendered hydrophobic through ionic exchange of the sodium interlayer cation with an onium cation, may be prepared via various synthetic routes comprising exfoliation adsorption, in situ intercalative polymerization and melt intercalation. The whole range of polymer matrices is covered, i.e. thermoplastics, thermosets and elastomers. Two types of structure may be obtained, namely intercalated nanocomposites where the polymer chains are sandwiched in between silicate layers and exfoliated nanocomposites where the separated, individual silicate layers are more or less uniformly dispersed in the polymer matrix. This new family of materials exhibits enhanced properties at very low filler level, usually inferior to 5 wt.%, such as increased Young’s modulus and storage modulus, increase in thermal stability and gas barrier properties and good flame retardancy.
5,901 citations
1,102 citations
1,031 citations
TL;DR: In this article, the future of mesoscopic properties of nanocomposite polymers is discussed, and several interesting results to indicate the foreseeable future have been revealed, some of which are described on materials and processing, together with basic concepts and future direction.
Abstract: Polymer nanocomposites are defined as polymers in which small amounts of nanometer size fillers are homogeneously dispersed by only several weight percentages. Addition of just a few weight percent of the nanofillers has profound impact on the physical, chemical, mechanical and electrical properties of polymers. Such change is often favorable for engineering purpose. This nanocomposite technology has emerged from the field of engineering plastics, and potentially expanded its application to structural materials, coatings, and packaging to medical/biomedical products, and electronic and photonic devices. Recently these 'hi-tech' materials with excellent properties have begun to attract research people in the field of dielectrics and electrical insulation. Since new properties are brought about from the interactions of nanofillers with polymer matrices, mesoscopic properties are expected to come out, which would be interesting to both scientists and engineers. Improved characteristics are. expected as dielectrics and electrical insulation. Several interesting results to indicate the foreseeable future have been revealed, some of which are described on materials and processing in the paper together with basic concepts and future direction.
889 citations
TL;DR: In this article, the propagation velocity matrix (PVM) and propagation time matrix (PTM) were introduced to detect partial discharge (PD) in power transformers, which can be used to index a database of physical descriptions of the transformer that could provide additional information to assist with diagnosis.
Abstract: Determining whether power transformers are suffering from internal arcing or dangerous levels of partial discharge (PD) is important because failure without warning can result in damage to neighboring equipment, customer dissatisfaction, disruption to economic activity, and the imposition of regulatory fines. This paper provides an overview of the excitation of UHF signals by PD inside transformers. The use of externally mounted sensors has been outlined, and the structure of a dielectric window that can be constructed on an inspection hatch has been outlined. Attenuation of UHF signals propagating inside a transformer tank has been shown to be relatively low. A new approach to locating PD sources in three dimensions has been presented, based on using a numerical model of the transformer materials, which defines electromagnetic propagation velocities on a mesh of 5-cm sub-cells. The concepts of the propagation-velocity matrix (PVM) and the propagation-time matrix (PTM) were thereby introduced. Once the PD source has been located to a specific region of the transformer, the PVM might be used to index a database of physical descriptions of the transformer that could provide additional information to assist with diagnosis.
390 citations