Utilization of sewage sludge in EU application of old and new methods—A review
TL;DR: In this article, the authors review past and future trends in sludge handling, focusing mainly at thermal processes (e.g. pyrolysis, wet oxidation, gasification) and the utilization of sewage sludge in cement manufacture as a co-fuel.
Abstract: The European Union has made progress in dealing with municipal wastewater in individual countries and as a corporate entity. However, it intends to make still further and substantial progress over the next 15 years. Currently, the most widely available options in the EU are the agriculture utilization, the waste disposal sites, the land reclamation and restoration, the incineration and other novel uses. The selection of an option on a local basis reflects local or national, cultural, historical, geographical, legal, political and economic circumstances. The degree of flexibility varies from country to country. In any case sludge treatment and disposal should always be considered as an integral part of treatment of wastewater. There is a wide range of other uses for sludge, which exploit its energy or chemical content, namely the thermal processes. The present paper sought to review past and future trends in sludge handling, focusing mainly at thermal processes (e.g. pyrolysis, wet oxidation, gasification) and the utilization of sewage sludge in cement manufacture as a co-fuel.
Citations
More filters
TL;DR: In this article, the authors examined the life cycle costs of the following four wastewater treatment methods: granular activated carbon, nanofiltration, solar photo-Fenton and ozonation.
59 citations
TL;DR: In this paper, the effects of variations in SiO2 and Al2O3 content on characteristics of LWA, including physical characteristics, morphological structures, crystal phases, and stabilization of heavy metals were evaluated.
58 citations
TL;DR: This study attempted to synthesize a novel ceramsite with excellent adsorption property compositing through the co-combustion of biomass and sewage sludge ash (CBSA), gasification of coal fly ash (GCFA) and sewagesludge (SS) to dispose wastewater contaminated by Pb (II).
58 citations
TL;DR: Thermogravimetric analysis results showed that high temperature pyrolysis could improve the thermal stability of the derived char and catalytic inorganic compounds improved the combustion reactivity of both the IS and MS-derived char.
58 citations
TL;DR: An empirical second-order polynomial model was developed for the ATH process with high levels of oxidant, and it is possible to achieve an organic matter removal of up to 92%, but the conditions required are prohibitive on an industrial scale.
Abstract: The aim of this work was to study in depth the behavior and optimization of a novel process, called advanced thermal hydrolysis (ATH), to determine its utility as a pretreatment (sludge solubilization) or postreatment (organic matter removal) for anaerobic digestion (AD) in the sludge line of wastewater treatment plants (WWTPs). ATH is based on a thermal hydrolysis (TH) process plus hydrogen peroxide (H(2)O(2)) addition and takes advantage of a peroxidation/direct steam injection synergistic effect. On the basis of the response surface methodology (RSM) and a modified Doehlert design, an empirical second-order polynomial model was developed for the total yield of: (a) disintegration degree [DD (%)] (solubilization), (b) filtration constant [F(c) (cm(2)/min)] (dewaterability), and (c) organic matter removal (%). The variables considered were operation time (t), temperature reached after initial heating (T), and oxidant coefficient (n = oxygen(supplied)/oxygen(stoichiometric)). As the model predicts, in the case of the ATH process with high levels of oxidant, it is possible to achieve an organic matter removal of up to 92%, but the conditions required are prohibitive on an industrial scale. ATH operated at optimal conditions (oxygen amount 30% of stoichiometric, 115 °C and 24 min) gave promising results as a pretreatment, with similar solubilization and markedly better dewaterability levels in comparison to those obtained with TH at 170 °C. The empirical validation of the model was satisfactory.
58 citations
References
More filters
TL;DR: In this paper, an analytical procedure involving sequential chemicai extractions was developed for the partitioning of particulate trace metals (Cd, Co, Cu, Ni, Pb, Zn, Fe, and Mn) into five fractions: exchangeable, bound to carbonates, binding to Fe-Mn oxides and bound to organic matter.
Abstract: An analytical procedure involving sequential chemicai extractions has been developed for the partitioning of particulate trace metals (Cd, Co, Cu, Ni, Pb, Zn, Fe, and Mn) into five fractions: exchangeable, bound to carbonates, bound to Fe-Mn oxides, bound to organic matter, and residual. Experimental results obtained on replicate samples of fluvial bottom sediments demonstrate that the relative standard deviation of the sequential extraction procedure Is generally better than =10%. The accuracy, evaluated by comparing total trace metal concentrations with the sum of the five Individual fractions, proved to be satisfactory. Complementary measurements were performed on the Individual leachates, and on the residual sediments following each extraction, to evaluate the selectivity of the various reagents toward specific geochemical phases. An application of the proposed method to river sediments is described, and the resulting trace metal speciation is discussed.
10,518 citations
"Utilization of sewage sludge in EU ..." refers background in this paper
...Over the last decades, a great variety of extraction schemes, both simple and sequential have been developed and, although some methods have been widely used [12,13] none has been unreservedly accepted by the scientific community....
[...]
Book•
01 Jan 1972
TL;DR: Wastewater Engineering: An Overview of Wastewater Engineering, Methods and Implementation Considerations as mentioned in this paper is a good starting point for a discussion of the issues of wastewater engineering. But, it is not a complete survey of the entire literature.
Abstract: Wastewater Engineering: An Overview. Wastewater Flowrates. Wastewater Characteristics. Wastewater Treatment Objective, Methods, and Implementation Considerations. Introduction to Wastewater Treatment Plant Design. Physical Unit Operations. Chemical Unit Processes. Biological Unit Processes. Design of Facilities for Physical and Chemical Treatment of Wastewater. Design of Facilities for the Biological Treatment of Wastewater. Advanced Wastewater Treatment. Design of Facilities for the Treatment and Disposal of Sludge. Natural-Treatment Systems. Small Wastewater Treatment Systems. Management of Wastewater from Combined Sewers. Wastewater Reclamation and Reuse.
3,826 citations
TL;DR: In this article, a review of the current and future issues related to the combustion of sewage sludge is presented, and a number of technologies for thermal processing of sludge are discussed in three groups, i.e., mono-combustion, cocombustions and alternative processes.
1,026 citations
"Utilization of sewage sludge in EU ..." refers background in this paper
...Multiple hearth and fluidized bed furnaces are the most popular and the latter is becoming widely applied [24]....
[...]
...Analysis has shown that about 78–98% of Cd, Cr, Cu, Ni, Pb and Zn present in the sewage sludge are retained in the ash, whereas up to 98% of the Hg may be released into the atmosphere with the flue gas [24]....
[...]
...The whole process is occurring in two distinctive regimes [24]:...
[...]
TL;DR: In this article, the authors proposed a standardization with respect to grain size effects, commonly achieved by analyzing the sieve fraction <63μm, which is used to pin point major sources of metal pollution and to estimate the toxicity potential of dredged materials.
Abstract: Sediment analyses are used to pin‐point major sources of metal pollution and to estimate the toxicity potential of dredged materials on agricultural land. For source assessments (Part I of the present review) standardization is needed with respect to grain size effects, commonly achieved by analyzing the sieve fraction <63μm. Further aspects include sampling methods, evaluation of background data and extent of anthropogenic metal enrichment.
530 citations