scispace - formally typeset
Search or ask a question

Can you heat up a ceramic teapot? 

Heat transfer
Dielectric
Ceramic
Heat sink
Glass-ceramic

Answers from top 10 papers

More filters
Papers (10)Insight
Journal Article•DOI
Preparation of glass-ceramic materials from basaltic rocks and by-pass cement dust
G.A. Khater, M. R. Shehata Shehata, Esmat M. A. Hamzawy, Mostafa Mahmoud 
14 Feb 2017-Glass Technology-european Journal of Glass Science and Technology Part A
12 Citations
Considering the main component of the raw materials compositions for making glass ceramic materials they can be used as heat and fire resistant materials because of their low thermal conductivities, high oxidation resistance, and high softening and melting temperatures.
Journal Article•DOI
Fabrication and Joining of Ceramic Compact Heat Exchangers for Process Integration
Charles A. Lewinsohn, Merrill Anderson Wilson, Joseph Fellows, H. Anderson 
01 Jul 2012-International Journal of Applied Ceramic Technology
23 Citations
Ceramic heat exchangers permit operation at higher temperatures than with other materials.
Journal Article•DOI
Using laser radiation for the formation of capillary structure in flat ceramic heat pipes
Yu. E. Nikolaenko, S. M. Rotner 
01 Dec 2012-Technical Physics Letters
16 Citations
The thermal resistance of flat ceramic heat pipes with this capillary structure reaches 0.07°C/W, which is quite acceptable for their use as heat sinks in systems of thermal regime control for electronic components and as heat exchange plates for large-size thermoelectric conversion units.
Journal Article•DOI
Structure and Microwave dielectric properties of a novel temperature stable low-firing Ba2LaV3O11 ceramic
Jie Li, Liang Fang, Hao Luo, Ying Tang, Chunchun Li 
01 Jul 2016-Journal of The European Ceramic Society
26 Citations
All the results indicate that the Ba2LaV3O11 ceramic might be a promising candidate for low temperature cofired ceramic technology.
Journal Article•DOI
Crystallization kinetics, sintering, microstructure, and properties of low temperature co-fired magnesium aluminum silicate glass-ceramic
Zhenjun Qing, Wenzhan Zhou, Wenjie Xia, Hao Li 
15 Apr 2018-Journal of Non-crystalline Solids
13 Citations
The results showed that the prepared glass-ceramic can be considered as a potential candidate for the application of low temperature co-fired ceramic substrates.
Journal Article•DOI
Li4WO5: A temperature stable low-firing microwave dielectric ceramic with rock salt structure
Jie Li, Liang Fang, Hao Luo, Jibran Khaliq, Ying Tang, Chunchun Li 
01 Jan 2016-Journal of The European Ceramic Society
54 Citations
All the results indicate that the Li4WO5 ceramic is a promising candidate as a base material in low temperature cofired ceramic technology.
Journal Article•DOI
Yttrium oxynitride glasses: Properties and potential for crystallisation to glass-ceramics
Stuart Hampshire, E. Nestor, R. Flynn, Jacques Besson, Tanguy Rouxel, H. Lemercier, P. Goursat, M. Sebai, Derek P. Thompson, K. Liddell 
01 Jan 1994-Journal of The European Ceramic Society
120 Citations
Further improvements are possible if glass-ceramic processes using two-stage heat treatments are introduced.
Journal Article•DOI
Microstructure, piezoelectric and ferroelectric properties of Mn-added Na0.5Bi4.5Ti4O15 ceramics
Daojiang Gao, Kin Wing Kwok, Dunmin Lin 
01 May 2011-Current Applied Physics
34 Citations
Our results also demonstrate that the ceramic exhibits a good thermal stability up to around 500 °C.
Journal Article•DOI
TiB2–SiC-based ceramics as alternative efficient micro heat exchangers
Sahar Nekahi, Mohammad Vajdi, Farhad Sadegh Moghanlou, Kourosh Vaferi, Amir Motallebzadeh, Melis Ozen, Umut Aydemir, Jianjun Sha, Mehdi Shahedi Asl 
15 Oct 2019-Ceramics International
84 Citations
This article demonstrates the feasibility of better heat transfer and performance for ceramic heat exchangers.
Open access•Journal Article•DOI
Energy efficiency enhancement and waste heat recovery in industrial processes by means of the heat pipe technology: Case of the ceramic industry
Bertrand Delpech, Massimo Milani, Luca Montorsi, Davide Boscardin, Amisha Chauhan, Sulaiman Almahmoud, Brian Axcell, Hussam Jouhara 
01 Sep 2018-Energy
69 Citations
These figures support the application of the heat pipes based heat recovery to the ceramic process from the viewpoint of the improvement the energy efficiency and environmental impact and also of the economic investment.

Related Questions

Are ceramic tea kettles good?7 answers
How do you heat tea in a ceramic teapot?9 answers
How do you keep a ceramic teapot warm?15 answers
How hot can a ceramic casserole dish get?17 answers
How hot can ceramic brake pads get?8 answers
How long should you run a ceramic heater?6 answers

See what other people are reading

How effective are adsorption-based water filters for water quality for drinking water?
5 answers
Adsorption-based water filters, such as those utilizing powdered activated carbon (PAC) and metal-organic frameworks (MOFs), are highly effective for improving drinking water quality. These filters can efficiently remove taste- and odor-causing compounds, synthetic organic chemicals, heavy metals, and other contaminants from water. Studies have shown that combining PAC with ceramic membranes can significantly enhance the removal of organic pollutants and pharmaceuticals from water, while also mitigating membrane fouling. Additionally, MOF-based adsorbents have been successfully tested in home water filters, meeting stringent reduction thresholds for various metals, ensuring clean and safe drinking water. Overall, adsorption-based water filters offer a reliable and affordable solution for improving water quality and ensuring access to potable water.How cfrp waste can be utilised in mortar?
5 answers
CFRP waste can be effectively utilized in mortar to enhance its properties and reduce environmental impact. By incorporating recycled concrete powder (RCP) and spontaneous combustion gangue powder (SCGP) as supplementary materials, the mechanical and durability properties of mortar can be improved, with a suitable combination of 15% RCP and 15% SCGP maintaining comparable mechanical properties to control mixes. Additionally, the use of construction waste micro powder along with various other components like cement, sand, and additives can create construction mortar that reduces environmental pollution and waste. Furthermore, incorporating ceramic waste as a substitute for fine aggregate in mortars can lead to superior results, with 10% ceramic waste showing high strengths and improved microstructural properties. Overall, utilizing CFRP waste in mortar presents a sustainable solution for enhancing performance while reducing environmental impact.What are the potential environmental impacts of using Al2O3 as a coolant additive in the automobile air conditioning system?
5 answers
Using Al2O3 as a coolant additive in automobile systems can have significant environmental impacts. Studies have shown that Al2O3 nanoparticles enhance the cooling performance of radiators, leading to increased overall heat transfer coefficients and improved engine thermal efficiency. Additionally, the use of Al2O3 nanofluids in cooling systems has been found to reduce NOx emissions from vehicle engines, indicating a potential positive environmental impact. Furthermore, the addition of Al2O3 nanoparticles to coolant fluids can improve the heat transfer coefficient and cooling effectiveness of automotive cooling systems, potentially reducing fuel consumption and enhancing overall system efficiency. Overall, incorporating Al2O3 as a coolant additive in automobile air conditioning systems shows promise in improving performance while potentially mitigating environmental impacts.Was ist stress shielding?
5 answers
Stress shielding is a biomechanical phenomenon observed in various medical and engineering contexts. In orthopedics, stress shielding occurs around metallic implants, leading to adaptive changes in bone strength and stiffness, potentially causing implant loosening. This effect is also seen in ligament reconstruction, where nonabsorbable suture augmentation aims to protect the reconstructed ligament but may inadvertently reduce stress on it, impacting its final strength and composition. In the field of ceramic binder jetting, stress shielding arises from unbalanced stresses between printed and unprinted regions, affecting the density of the final part. In total shoulder arthroplasty, stress shielding of the humeral stem is common at midterm follow-up but does not significantly impact functional outcomes.Can membrane technology effectively remove microplastics?
5 answers
Membrane technology, particularly ultrafiltration, offers a promising solution for effectively removing microplastics from water systems. These membranes with small pores can filter out microplastics, addressing the growing concern of microplastic contamination in aquatic environments. However, challenges such as membrane fouling and the passage of smaller microplastics through the filter still exist, highlighting the need for continuous improvement in membrane design and technology. Studies have shown that different types and shapes of microplastics can impact the efficiency of filtration processes, emphasizing the importance of understanding these factors for enhancing microplastic removal efficacy. Overall, membrane-based methods like ultrafiltration demonstrate high potential for efficient microplastic separation, but ongoing research is essential to optimize membrane performance and minimize environmental impacts.How does the design of corrugated fins affect heat transfer in cool pv pennal systems?
9 answers
The design of corrugated fins significantly influences heat transfer in cooling photovoltaic (PV) panel systems by enhancing the efficiency and performance of these systems. Corrugated fins introduce higher disturbances in the flow, causing multiple separations and reattachments, which result in a higher localized heat transfer coefficient and enhanced heat transfer from the system. This is particularly evident in the corrugated plate-fin heat sink, where the maximum fin performance was observed with specific dimensions of corrugation, demonstrating the critical role of fin geometry in optimizing heat dissipation. Moreover, the structural parameters of corrugated fins, such as the corrugation number, area, and flow channel width, have been identified as key factors affecting the efficiency of PV/T systems. Adjustments in these parameters can lead to significant improvements in heat collection and the reduction of outlet temperatures, thereby increasing the overall thermal efficiency of hybrid PV/T systems. Experimental research further supports the effectiveness of fin cooling in silicon solar cells, where aluminum fins dispersed waste heat more efficiently, leading to substantial gains in power output and electrical efficiency. Enhanced rearward convection through simple aluminum fin structures has been shown to reduce operating temperatures and increase peak output power, indicating the potential for commercial adoption with optimized material use and design integration. The corrugation technique applied to the lower sides of PV modules, especially under turbulent flow conditions, has been proven to reduce temperature and enhance thermal efficiency significantly. Different fin geometries and arrangements, such as staggered arrays of cylindrical aluminum fins, have demonstrated improved performance by absorbing heat more effectively from the photovoltaic cells, thus increasing electrical efficiency. Innovative designs like partially submerged angle perforating fins (PSAPF) have shown remarkable efficiency in heat dissipation from floating PV systems, significantly enhancing productivity and reducing operating temperatures. The incorporation of aluminum rectangular fins in air cooling PV/T systems has been validated to improve thermal and electrical performance, with specific fin geometries yielding optimal results. Even in concentrated PV thermal (CPV-T) receivers, the application of metal fins has been found to slightly enhance cooling, with certain geometric factors like fin heights and gap distances playing a crucial role in heat transfer efficiency. Lastly, the use of corrugated booster reflectors in solar collectors for cooling PV cells has highlighted the importance of optimizing design parameters to achieve maximum energy and exergy efficiencies, further underscoring the significant impact of corrugated fin design on the thermal management of PV systems.What are the potential benefits of using recycled aluminum in composite materials?
4 answers
Recycling aluminum for composite materials offers various advantages. Firstly, it aids in waste management and reduces environmental pollution. Secondly, incorporating recycled aluminum in composites enhances properties like specific strength, stiffness, wear resistance, and thermal stability. Additionally, the reuse of aluminum waste in composites can lead to significant improvements in mechanical properties such as hardness, compressive strength, and tensile strength. Moreover, utilizing recycled aluminum in composites can result in cost-effective manufacturing processes while revaluing metallic waste. Overall, the use of recycled aluminum in composite materials not only contributes to sustainability by reducing resource depletion but also enhances material performance and offers economic benefits.What are the advantages of using WAAM in manufacturing processes?
5 answers
Wire Arc Additive Manufacturing (WAAM) offers several advantages in manufacturing processes. WAAM enables the efficient production of large-scale components with reduced lead times, minimal material waste, and cost-effectiveness. It has been successfully utilized in various industries like aerospace, automotive, and shipbuilding. The technology allows for the in-situ manufacturing of complex structures with integrated material-structure-function components, providing solutions for components with surface performance requirements and individual structural features. WAAM also exhibits high efficiency in fabricating components, while the hybridization with Laser Directed Energy Deposition (LDED) enhances precision and surface flatness, resulting in well-fabricated samples with improved mechanical properties and microstructures. Additionally, WAAM materials have shown good yield and ultimate strengths, albeit with slightly lower ductility compared to conventional stainless steel, making them suitable for construction applications.What are the different mechanisms of cooling fabrics?
5 answers
Different mechanisms of cooling fabrics include utilizing cooling assemblies with air guide plates and fans to perform uniform cooling treatment on fiber cloth. Another mechanism involves inducing heat exchange through a heat exchanger and a fan blowing cooled air onto non-woven fabrics, aided by a tension roll system for fabric movement. Additionally, a unique mechanism involves micro-size ribbed surfaces on knitted stockings that enhance thermal conduction and promote heat release through a fluid-solid conjugate heat transfer analysis, creating a cooling effect on the body. Furthermore, fabric properties like thickness, grammage, and thermal conductivity influence the transient cool feeling of fabrics, with volumetric heat capacity and thickness being key factors in enhancing cooling sensation. These mechanisms collectively contribute to efficiently cooling fabrics during various processes like ironing and textile treatment.What is the current state of literature on die sinking Electrical Discharge Machining (EDM) using two different electrodes?
5 answers
The current literature on die sinking Electrical Discharge Machining (EDM) using different electrodes highlights various aspects. Studies have explored unconventional electrode designs, such as those with circular relief angles, showcasing improved performance in terms of Material Removal Rate (MRR), tool wear rate, overcut, taper angle, and surface roughness of machined holes. Additionally, research has compared the wear performance of copper and copper/nickel electrodes when machining aluminum alloys, indicating that copper electrodes exhibit significantly slower wear rates compared to copper/nickel electrodes. Furthermore, investigations into the impact of electrode materials with varying melting points on Material Removal Rate (MRR) have been conducted, revealing that materials with higher melting points require longer processing times and result in higher surface roughness.What is aluminum combustion mode on thermal explosion can occurs ?
4 answers
Aluminum combustion in the mode of thermal explosion (TE) can occur under various conditions and mechanisms, as elucidated by multiple studies. The general theory of thermal explosion, developed by N. N. Semenov, indicates that combustion synthesis (CS) systems, including those involving aluminum, exhibit a non-monotonic dependence of reaction rate on temperature, where phenomena such as melting of the precursor can sharply increase the reaction rate. This is particularly relevant in the formation of aluminum-based composites and alloys, where the thermal explosion mode of combustion synthesis method triggers reactions between aluminum and other materials, as seen in the creation of Cu-Al alloys. Mechanochemical treatment (MCT) has been shown to influence thermal explosion in aluminum powder blends, enhancing the maximum temperature of thermal explosion and stabilizing the combustion process. This suggests that the physical manipulation of aluminum particles can affect their reactivity and the conditions under which thermal explosion occurs. The size of aluminum particles plays a significant role in their ignition and combustion behavior. Studies on nano- and micro-sized aluminum particles have shown that ignition temperature varies significantly with particle size, influenced by the mode of heat transfer to the particle. This indicates that thermal explosion in aluminum systems can be critically dependent on the physical characteristics of the aluminum itself. Furthermore, the presence of a constant magnetic field has been found to influence the combustion of aluminum nanopowder under thermal explosion conditions, favoring the formation of specific compounds. This highlights the complex interplay of external conditions and material properties in determining the combustion mode of aluminum. In situ fabrication of aluminum metal matrix composites via thermal explosion reveals that aluminum not only acts as a diluent but also participates in the reaction, affecting both the process and the final products. This participation is crucial in the thermal explosion synthesis of materials involving aluminum. The study of aluminum and copper powder mixtures heated to self-ignition temperatures further elucidates the phase transformations and kinetics of heat release during thermal explosion, providing insight into the macrokinetic stages of aluminum combustion. Lastly, experiments with molten aluminum have shown that thermal explosion can occur with varying degrees of intensity, influenced by the temperature of the aluminum melt and the conditions of the experiment. This underscores the variability of thermal explosion phenomena in aluminum systems under different thermal conditions. In summary, aluminum combustion in the mode of thermal explosion can occur through various mechanisms, influenced by factors such as the physical treatment of aluminum, particle size, external magnetic fields, and the specific conditions of the reaction environment.