scispace - formally typeset
Search or ask a question

Does inverter cause voltage fluctuations? 

Answers from top 18 papers

More filters
Papers (18)Insight
The inverter may also cause a reduction in the power factor and in the overall efficiency of the drive.
It should constitute a reliable theoretical framework for further analysis of the impact of time fluctuations on the static and dynamic operation of CMOS inverter based circuits.
The numbers of inverter voltage levels are always same, and hence, their total harmonic distortion also remains nearly constant at different speeds of operation.
Therefore, the fluctuating power causes frequency and voltage fluctuations.
Such low modulation usually leads to high-voltage stresses across the components and poor spectral performance at the inverter output.
Therefore, it can cause frequency fluctuations or voltage fluctuations in the power system.
Since the induction generators do not perform voltage regulation and absorb reactive power from the utility grid, they are often the source of voltage fluctuations.
This is because individual inverter output voltage phase angle and magnitude are sensitive to certain circuit uncertainty, for instance, component tolerance.
Negative resistance can cause impedance-based interactions which may lead to instability, especially, when the inverter is connected to a weak grid which has large inductance.
This results in a significant reduction of the fluctuations of the neutral point voltage of NPC inverters.
These control methods cause the three-phase inverters to substitute reactive output power for real output power when fluctuations in the solar power are experienced, allowing the fluctuations to be controlled.
Therefore, fluctuations occur in systems voltage and frequency.
Therefore the voltage drops across the switches are mitigated and as a result the efficiency of the presented inverter is improved.
The obtained results lead to the following conclusions: not all efficient lamps have a lower sensitivity to fluctuations than do incandescent lamps; the response of some lamps depends on the complexity of the input voltage fluctuation; and the response of some lamps in real scenarios, i. e., more complex voltage fluctuations, does not correlate with their response to simple voltage fluctuations.
The paper presents a novel technique for an accurate identification of the inverter nonlinear effects, such as the dead-time and on-state voltage drops.
The simulation and experimental results show that the proposed technique provides seamless transition between the inverter modes of operation with minimal distortion at the inverter output voltage.
This paper presents an enhanced average model of a voltage source inverter (VSI) that can accurately predict some of the low frequency phenomena only seen by the switching models.

See what other people are reading

How to measure the power consumption for camera modules in projects?
5 answers
To measure the power consumption of camera modules in projects, various methods and devices have been developed. One approach involves using a power consumption measurement circuit that includes current and voltage sampling components for accurate measurements. Another method focuses on controlling power consumption by dynamically adjusting the working time and brightness of projectors based on distance data from the target object, effectively reducing power usage. Additionally, a camera power consumption control method involves predicting and accumulating power consumption values to ensure that the total power consumption remains below a set threshold, optimizing power usage during camera operation. Furthermore, a multi-channel camera module measuring device integrates power supply control, motion measurement, and operational testing to efficiently assess camera modules' performance and power usage in a cost-effective manner.
How does the conversion process of solar power satellites (SPS) work to generate energy?
5 answers
Solar Power Satellites (SPS) harness solar energy in space and transmit it to Earth as electricity. The process involves converting solar energy into microwaves using Microwave Power Transmission technology. These satellites collect solar energy, convert it into DC power, store it in batteries, and then transform it into RF energy using a device called Magnetron for transmission to Earth. New SPS projects aim to improve efficiency by utilizing heat-resistant carbonic nanocomposite materials and low-temperature superconductors for solar energy conversion, eliminating the need for steam and gas turbine plants. Additionally, a modular approach with Solar Module Integrated Converters (SMIC) has been proposed to reduce costs and development time for the Electrical Power System of satellites, ensuring efficient power generation and transmission.
What are the specific manufacturing standards that dictate the optimal temperature range for photovoltaic solar panels?
5 answers
The optimal temperature range for photovoltaic solar panels is governed by specific manufacturing standards such as IEC 61730-2 and ANSI/UL 1703. These standards provide procedures to determine the maximum reference temperatures of various components and materials of a PV module, ensuring safety and functionality requirements are met. Additionally, the International Electrotechnical Committee (IEC) has defined standard test conditions (STC) for PV modules, specifying 25°C module temperature as part of the testing criteria. Moreover, research has shown that the performance of PV panels can be significantly improved by reducing operating temperatures, with experimental studies demonstrating a 10°C temperature decrease leading to a 5% power improvement and better regulation of electrical output.
What has been proven challenging for renewables in general?
5 answers
The deployment of renewable energy technologies (RETs) faces various challenges. These challenges include inflexible and ineffective regulatory frameworks, limited financing options, insufficient societal awareness. Additionally, integrating renewable energy into the electricity network poses technical challenges such as fluctuating power generation due to weather-dependent sources like solar and wind power. Furthermore, the transition to renewables requires overcoming barriers like the need for accurate steady-state and dynamic models for large renewable power plants, compliance with grid codes, and ensuring proper operation through cooperation with transmission system operators. Overall, challenges in regulatory, financial, societal awareness, technical integration, and operational aspects hinder the widespread adoption and diffusion of renewable energy technologies.
What are the primary components of a generation station in the context of power systems?
4 answers
A power generation station typically consists of several key components. These include a combustor for generating a circulating fluid by burning fuel, an expander for converting the fluid's energy into power, a power generator for electricity production, a compressor for fluid compression, and a pump for circulation. Additionally, a displacement measuring part may be present to measure the movement of a generator's parts, along with a converter to adjust the electric power's voltage level based on this measurement. Furthermore, some systems utilize permanent magnets to generate rotational force for power generation without physical transmission structures, incorporating multiple power generators, an integrated substation for electricity distribution, and a control room for system management. Other configurations may involve waste heat circulating systems with shared evaporators and cooling agent control valves to optimize equipment utilization and prevent working oil loss.
How to calculate the air velocity generated by fan in wind tunnel ?
4 answers
To calculate the air velocity generated by a fan in a wind tunnel, various methods and technologies have been developed. One approach involves establishing a fan wind energy calculation model based on different wind speeds before and after passing through the fan, as well as the fan area and air density. Additionally, a wind tunnel active simulation method utilizes an array of fans with adjustable deflection angles to simulate different wind profiles accurately. Furthermore, adjusting the fan rotor blade setting angle based on the fan rotating speed and flow velocity in the wind tunnel test section can optimize fan performance without the need for total pressure rise measurements, saving costs and ensuring reliable results. These methods collectively contribute to accurately determining and controlling the air velocity generated by fans in wind tunnels.
What is the file structure of Dig silent power factory .dsg file ?
4 answers
The file structure of a DIgSILENT PowerFactory .dgs file is primarily used for storing simulation data and settings within the software. This file format is crucial for saving and loading simulation scenarios, network configurations, and analysis results in PowerFactory. The .dgs file contains detailed information about the modeled power system elements, such as generators, transmission lines, loads, and protection devices, enabling users to simulate and analyze various studies in the power grid. Additionally, the .dgs file may store Python code snippets for task automation within PowerFactory, showcasing the software's flexibility and integration capabilities. Overall, the .dgs file serves as a comprehensive repository for all the necessary data and configurations required for conducting advanced power system studies and analyses using DIgSILENT PowerFactory.
How does the distribution system in a power system affect the overall efficiency of energy transmission?
5 answers
The distribution system in a power system significantly impacts the overall efficiency of energy transmission. By correcting power factors through the installation of capacitors at each consumer, voltage drop and power losses in wires can be reduced, enhancing system efficiency. Additionally, utilizing direct-current (DC) power distribution with energy storage devices at edge devices allows for more efficient power delivery to loads like LED devices. Implementing a well-structured power distribution system with multiple power supply paths, transformer banks, and breakers can enhance operational flexibility, reduce equipment costs, and improve equipment utilization rates, thereby increasing overall efficiency of the distribution system. Moreover, incorporating various cooling mechanisms like air blowing, air exhaust, and water circulation in the distribution system helps maintain optimal operating temperatures, further enhancing efficiency. Integrating monitoring devices and terminals for data analysis and real-time monitoring improves distribution station efficiency, ensuring stable and secure operations.
What are the various forms of renewable energy sources in Indonesia?
4 answers
Renewable energy sources in Indonesia include wind energy, solar energy, biomass energy, geothermal energy, and hydro energy. Indonesia has significant potential in renewable energy, with 419 GW capacity, including 75 GW of hydro energy, 23.7 GW of geothermal, 32.6 GW of bioenergy, 207.8 GW of solar, and 60.6 GW of wind energy. Wind energy can be harnessed through large-scale wind turbines or Small Wind Turbines, with studies focusing on wind mapping for optimal design. Solar energy is abundant throughout the year in Indonesia, making it a promising renewable energy source, with calibration methods like the Continuous Sun and Shade Method being developed for accurate measurements. Additionally, achieving Indonesia's net-zero emissions target involves utilizing nuclear power, energy storage, and decommissioning fossil fuel power plants, emphasizing the importance of diverse renewable energy sources.
What is the role of the dc link capacitor in the PV system regarding the ripple effect?
5 answers
The DC-link capacitor in a PV system plays a crucial role in smoothing voltage ripples and stabilizing the DC voltage. It helps in charging/discharging, smoothing the DC voltage, and stabilizing fluctuations in the DC-link voltage. The selection of an appropriate capacitance for the DC-link capacitor is essential, as it directly impacts the system's voltage stabilization. While larger capacitance is ideal for voltage stabilization, practical limitations such as cost, volume, and size constraints need to be considered. Different PWM strategies can affect the DC-link voltage ripple, emphasizing the importance of analyzing ripple effects to determine the optimal capacitance for the DC-link capacitor.
How does the DC link capacitor affect the ripple effect in a PV system?
5 answers
The DC-link capacitor in a PV system plays a crucial role in smoothing the DC voltage and reducing ripple effects. Capacitors are commonly used in PV inverters for their fast charging/discharging characteristics. However, issues like leakage current due to parasitic capacitance can arise, affecting system efficiency. To address this, innovative solutions like using a Boost converter to eliminate leakage current and transferring ripple to a separate capacitor have been proposed, enhancing system performance. Additionally, strategies involving switched-capacitor topologies have been suggested to suppress voltage ripples and limit short-circuit currents, improving system stability. By monitoring the DC-link capacitor's condition and capacitance changes, potential failures and safety hazards can be preemptively managed, ensuring the reliability and longevity of PV systems.