How do you cut nitrocellulose membrane?
Answers from top 10 papers
More filters
| Papers (10) | Insight |
|---|---|
| The method is versatile and allows for controlled through-cutting and ablative etching of nitrocellulose substrates. | |
| Third, nitrocellulose membranes can be cast that have pores sufficiently large to allow lateral flow of fluid in a reasonable time. | |
79 Citations | The new digest procedure takes just 2 h to complete and requires 5 ng protease per 1 microliter buffer per 1 mm2 of nitrocellulose; relatively large pieces of membrane (> or = 100 mm2) can be successfully processed. |
24 Citations | These results suggest that acid binding of proteins could increase the sensitivity of nitrocellulose membrane assays using a milk block. |
| To facilitate the utilization of nitrocellulose in lateral-flow assays, the membrane can be cast directly onto a polyester backing. | |
| A double-layered nitrocellulose (NC) membrane structure is proposed in this paper as an alternative holder for small quantities of either dry or wet pure (no added polyethylene powder) samples with significantly reduced etalon artifacts. | |
Open access•Journal Article | Nitrocellulose membrane after treatment has such merit as good lucidity and stability without toxicity on the cells. |
Open access•Journal Article 5 Citations | In conclusion, nitrocellulose membrane method is generally the same as acetone precipitation method. |
16 Citations | Columns of nitrocellulose have some advantage over membrane filters in that the capacity of the technique is increased and the recovery of adsorbed nucleic acids is improved. |
26 Citations | The eventuality of decreased or absent identification of some antigens on nitrocellulose membranes stresses the importance of controls using nylon membranes. |
Related Questions
What are the most effective catalysts for accelerating the nitration process of cellulose for nitrocellulose?5 answersThe most effective catalysts for accelerating the nitration process of cellulose for nitrocellulose include FeCl3·6H2O, ZnCl2, and nitrating acid mixtures containing HNO3 and H2SO4 or P2O5. FeCl3·6H2O and ZnCl2 were found to yield cellulose propionate with high degrees of substitution and varying yields, impacting the degree of polymerization and thermal stability of the resulting product. Additionally, the use of nitrating acid mixtures containing HNO3 and H2SO4 or P2O5 significantly intensifies the nitration process of cellulose, leading to low-nitrogen cellulose nitrates with improved physical and chemical characteristics, such as nitrogen content, solubility, viscosity, and chemical resistance. These catalysts and nitrating agents play crucial roles in enhancing the efficiency and quality of the nitration process for cellulose to produce nitrocellulose.
How effective are alternative materials to nitrocellulose in terms of performance and cost-effectiveness in various applications?5 answersAlternative materials to nitrocellulose, such as nitrated structurally modified cellulosic biopolymers (NNCs) derived from lignocellulosic feedstocks, have shown promising performance in various applications. These NNCs have higher densities and nitrogen contents compared to conventional nitrocellulose, making them suitable for use in solid propellant formulations and composite explosives. Additionally, the use of a nitrocellulose substitute in paint formulations has resulted in reduced volatile organic compound (VOC) content and improved performance, while also alleviating environmental pollution. Furthermore, the nitration of cellulose from deciduous tree species has led to the production of cellulose nitrate with a nitrogen mass fraction greater than 10%, indicating its potential for various applications. Microcrystalline cellulose nitrate derived from Alfa grass has shown improved properties such as higher crystallinity, thermal stability, and nitrogen content, making it suitable for propellant and gas generator components. Finally, the synthesis of aminated and nitrated cellulose and microcrystalline cellulose has resulted in energy-rich dense biopolymers with superior performance compared to nitrated unmodified cellulosic biopolymers.
What are the different ways of cutting trees?5 answersThere are different ways of cutting trees. One method involves using a tree cutting device that consists of a cross beam, an operation handle, a cutting table, a cutting wheel, and a base. Another approach is to focus on the higher degree vertices of a random recursive tree and sequentially remove them, keeping only the subtree containing the root after each removal. Cut trees, on the other hand, are combinatorial structures that represent the edge-connectivity between all pairs of vertices in an undirected graph and are used to efficiently solve the all pairs minimum s-t-cut problem. In the cutting process of a tree-shaped groove, rough cutting is performed first, followed by semi-finishing and finishing processes using different cutting tools.
Why nitroglycerin patches must not be cut?2 answersNitroglycerin patches must not be cut because cutting the patch can affect the absorption of the medication and may lead to inadequate or uneven delivery of nitroglycerin. Cutting the patch can also alter the release rate of the medication, potentially causing an overdose or underdose of nitroglycerin. Additionally, cutting the patch may compromise the integrity of the patch, leading to leakage or loss of the medication.
How do you remove membrane from pork?10 answers
How to cut spinal cord?3 answers