scispace - formally typeset
Search or ask a question
Topic

Alloy

About: Alloy is a research topic. Over the lifetime, 171884 publications have been published within this topic receiving 1719420 citations. The topic is also known as: alloys.


Papers
More filters
Journal ArticleDOI
TL;DR: In this article, a Zr41.2Ti13.8Cu12.5Ni10Be22.5 alloy, machined into 7 mm wide, 38 mm thick compact-tension specimens and fatigue precracked following standard procedures, revealed fracture toughnesses in the fully amorphous structure of K(lc)similar to 55 MPa root m, i.e., comparable with that of a high-strength steel or aluminum ahoy.
Abstract: The recent development of metallic alloy systems which can be processed with an amorphous structure over large dimensions, specifically to form metallic glasses at low cooling rates (similar to 10 K/s), has permitted novel measurements of important mechanical properties. These include, for example, fatigue-crack growth and fracture toughness behavior, representing the conditions governing the subcritical and critical propagation of cracks in these structures. In the present study, bulk plates of a Zr41.2Ti13.8Cu12.5Ni10Be22.5 alloy, machined into 7 mm wide, 38 mm thick compact-tension specimens and fatigue precracked following standard procedures, revealed fracture toughnesses in the fully amorphous structure of K(lc)similar to 55 MPa root m, i.e., comparable with that of a high-strength steel or aluminum ahoy. However, partial and full crystallization, e.g., following thermal exposure at 633 K or more, was found to result in a drastic reduction in fracture toughness to similar to 1 MPa root m, i.e., comparable with silica glass. The fully amorphous alloy was also found to be susceptible to fatigue-crack growth under cyclic loading, with growth-rate properties comparable to that of ductile crystalline metallic alloys, such as high-strength steels or aluminum alloys; no such fatigue was seen in the partially or fully crystallized alloys which behaved like very brittle ceramics. Possible micromechanical mechanisms for such behavior are discussed.

423 citations

Journal ArticleDOI
TL;DR: The best corrosion behaviour of the AZ31 alloy was obtained for the finest grain alloy associated with the highest transfer resistance value, after long periods of immersion in PBS.

422 citations

Journal ArticleDOI
TL;DR: In this paper, three-dimensional atom-probe tomography studies demonstrate that the distribution of Al is highly inhomogeneous in the sintered bulk samples, and Al-containing precipitates including Al(Cu,Zn)−O−N, Al-O-N and Al−N are distributed in the matrix.

420 citations

Book ChapterDOI
01 Jan 1987
TL;DR: In this article, the authors presented a theory of liquid alloys and assembled all the necessary tools for the ab initio construction of an alloy phase diagram, which they used to construct a phase diagram.
Abstract: With the presentation of a theory of liquid alloys, we have now assembled all the necessary tools for the ab initio construction of an alloy phase diagram.

417 citations

Journal ArticleDOI
TL;DR: In this paper, the glass-liquid transition was exhibited thermally by both binary and ternary alloys, and the stability, ease of formation and glass transition temperature, Tg, of the glasses were all increased by the replacement of Pd with small concentrations of the noble metals.

416 citations


Network Information
Related Topics (5)
Microstructure
148.6K papers, 2.2M citations
96% related
Coating
379.8K papers, 3.1M citations
89% related
Ultimate tensile strength
129.2K papers, 2.1M citations
87% related
Thin film
275.5K papers, 4.5M citations
87% related
Amorphous solid
117K papers, 2.2M citations
87% related
Performance
Metrics
No. of papers in the topic in previous years
YearPapers
202310,509
202220,674
20215,930
20208,500
20199,616
20189,122