Buck–boost converter

About: Buck–boost converter is a research topic. Over the lifetime, 15413 publications have been published within this topic receiving 233614 citations.

Z-source inverter

Abstract: This paper presents an impedance-source (or impedance-fed) power converter (abbreviated as Z-source converter) and its control method for implementing DC-to-AC, AC-to-DC, AC-to-AC, and DC-to-DC power conversion. The Z-source converter employs a unique impedance network (or circuit) to couple the converter main circuit to the power source, thus providing unique features that cannot be obtained in the traditional voltage-source (or voltage-fed) and current-source (or current-fed) converters where a capacitor and inductor are used, respectively. The Z-source converter overcomes the conceptual and theoretical barriers and limitations of the traditional voltage-source converter (abbreviated as V-source converter) and current-source converter (abbreviated as I-source converter) and provides a novel power conversion concept. The Z-source concept can be applied to all DC-to-AC, AC-to-DC, AC-to-AC, and DC-to-DC power conversion. To describe the operating principle and control, this paper focuses on an example: a Z-source inverter for DC-AC power conversion needed in fuel cell applications. Simulation and experimental results are presented to demonstrate the new features.

A comparison of half-bridge resonant converter topologies

Abstract: The half-bridge series-resonant, parallel-resonant, and combination series-parallel resonant converters are compared for use in low-output-voltage power supply applications. It is shown that the combination series-parallel converter, which takes on the desirable characteristics of the pure series and the pure parallel converter, avoids the main disadvantages of each of them. Analyses and breadboard results show that the combination converter can run over a large input voltage range and a large load range (no load to full load) while maintaining excellent efficiency. A useful analysis technique based on classical AC complex analysis is introduced. >

Switched reluctance motor drives : modeling, simulation, analysis, design, and applications

Abstract: PRINCIPLE OF OPERATION OF THE SWITCH RELUCTANCE MOTOR (SRM) Introduction Background Elementary Operation of the Switch Reluctance Motor Principle of Operation of the Switched Reluctance Motor Derivation of the Relationship Between Inductance and Rotor Position Equivalent Circuit SRM Configurations Linear Switched Reluctance Machines References DERIVATION OF SRM CHARACTERISTICS Introduction Data for Performance Computation Analytic Method for the Computation of Machine Characteristics Computation of Unaligned Inductance Computation of Aligned Inductance Computation of Inductance vs. Rotor Position vs. Excitation Current Comparison of Measured, Analytic and Finite Element Results References DESIGN OF SRM Introduction Derivation of Output Equation Selection of Dimensions Design Verification Operational Limit Selection of Number of Phases Selection of Poles Ratio of Pole-Arc to Pole-Pitch Selection of Pole Base Selection of Pole-Arcs Measurement of Inductance Calculation of Torque Design of Linear Switched Reluctance Machine (LSRM) References CHAPTER 4: CONVERTERS FOR SRM DRIVES Converter Configurations Asymmetric Bridge Converter Asymmetric Converter Variation Single Switch per Phase Converters m Switches and 2m Diodes m Switches and 2m Diodes with Independent Phase Current Control (m+1) Switch and Diode Configurations One Common Switch Configuration Minimum Switch Topology With Variable DC Link Variable DC Link Voltage with Buck Boost Converter Topology 1.5m Switches and Diodes Configuration Comparison of Some Power Converters Two Stage Power Converter Resonant Converter Circuits for Switched Reluctance Motor Drives References CONTROL OF SRM DRIVE Introduction Control Principle Closed Loop Speed Controlled SRM Drive Design of Current Controllers Flux Linkage Controller Torque Control Design of the Speed Controller References MODELING AND SIMULATION OF SRM DRIVE SYSTEM Introduction Modeling Simulation References ACOUSTIC NOISE AND ITS CONTROL IN SRM Introduction Sources of Acoustic Noise in Electrical Machines Noise Sources Noise Mitigation Qualitative Design Measures to Reduce Noise Measurement of Acoustic Noise and Vibrations Future Directions Appendix-1: Derivation of First Mode Frequency of SRM References SENSORLESS OPERATION OF SRM DRIVES Introduction Current Sensing Rotor Position Measurement Methods Rotor Position Estimation References APPLICATION CONSIDERATIONS AND APPLICATIONS Introduction Review of SRM Drive Features for Application Consideration Applications Emerging applications References

LLC resonant converter for front end DC/DC conversion

Abstract: A new LLC resonant converter is proposed for front end DC/DC conversion in a distributed power system. Three advantages are achieved with this resonant converter. First, ZVS turn on and low turn off current of MOSFETs are achieved. The switching loss is reduced so we can operate the converter at higher switching frequency. The second advantage is that with this topology, we can optimize the converter at high input voltage. Finally, with this topology, we can eliminate the secondary filter inductor, so the voltage stress on the secondary rectifier will be limited to two times the output voltage, better rectifier diodes can be used and secondary conduction loss can be reduced. The converter utilizes leakage and magnetizing inductance of a transformer. With magnetic integration concept, all the magnetic components can be built in one magnetic core. The operation and characteristic of this converter is introduced and efficiency comparison between this converter and a conventional PWM converter is given which shows a great improvement by using this topology.

Analysis and design of optimum-amplitude nine-switch direct AC-AC converters

Abstract: The maximum input-output transformer ratio, or output voltage ability, of direct AC-AC pulse-width-modulated converters is explored. An intrinsic limit, independent of the control algorithm, is found. A suitable novel converter control algorithm is discussed which achieves such maximum output amplitude ability and displays some interesting features. Finally, the opportunity to implement AC-AC converter control with the use of feedback techniques is considered, and a feedback-based control algorithm for the converter is proposed. >