Charge pump

About: Charge pump is a research topic. Over the lifetime, 14306 publications have been published within this topic receiving 182181 citations.

A three-phase soft-switched high power density DC/DC converter for high power applications

Abstract: Three DC/DC converter topologies suitable for high-power-density high-power applications are presented. All three circuits operate in a soft-switched manner, making possible a reduction in device switching losses and an increase in switching frequency. The three-phase dual-bridge converter proposed is shown to have the most favorable characteristics. This converter consists of two three-phase inverter stages operating in a high-frequency six-step mode. In contrast to existing single-phase AC-link DC/DC converters, lower turn-off peak currents in the power devices and lower RMS current ratings for both the input and output filter capacitors are obtained. This is in addition to smaller filter element values due to the higher-frequency content of the input and output waveforms. Furthermore, the use of a three-phase symmetrical transformer instead of single-phase transformers and a better utilization of the available apparent power of the transformer (as a consequence of the controlled output inverter) significantly increase the power density attainable. >

Step-Up DC–DC Converters: A Comprehensive Review of Voltage-Boosting Techniques, Topologies, and Applications

Abstract: DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques.

High-efficiency, high step-up DC-DC converters

Abstract: Many applications call for high step-up DC-DC converters that do not require isolation. Some DC-DC converters can provide high step-up voltage gain, but with the penalty of either an extreme duty ratio or a large amount of circulating energy. DC-DC converters with coupled inductors can provide high voltage gain, but their efficiency is degraded by the losses associated with leakage inductors. Converters with active clamps recycle the leakage energy at the price of increasing topology complexity. A family of high-efficiency, high step-up DC-DC converters with simple topologies is proposed in this paper. The proposed converters, which use diodes and coupled windings instead of active switches to realize functions similar to those of active clamps, perform better than their active-clamp counterparts. High efficiency is achieved because the leakage energy is recycled and the output rectifier reverse-recovery problem is alleviated.

Charge-Pump Phase-Lock Loops

Abstract: Phase/frequency detectors deliver output in the form of three-state, digital logic. Charge pumps are utilized to convert the timed logic levels into analog quantities for controlling the locked oscillators. This paper analyzes typical charge-pump circuits, identifies salient features, and provides equations and graphs for the design engineer.

Adaptive impedance tuning in wireless power transmission

Abstract: Exemplary embodiments are directed to wireless power. A wireless power receiver includes a receive antenna for coupling with near field radiation in a coupling-mode region generated by a transmit antenna operating at a resonant frequency. The receive antenna generates an RF signal when coupled to the near filed radiation and a rectifier converts the RF signal to a DC input signal. A direct current (DC)-to-DC converter coupled to the DC input signal generates a DC output signal. A pulse modulator generate a pulse-width modulation signal to the DC-to-DC converter to adjust a DC impedance of the wireless power receiver by modifying a duty cycle of the pulse-width modulation signal responsive to at least one of a voltage of the DC input signal, a current of the DC input signal, a voltage of the DC output signal, and a current of the DC output signal.