Ductility

About: Ductility is a research topic. Over the lifetime, 23427 publications have been published within this topic receiving 420674 citations.

Additive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling

Abstract: Additive manufacturing (AM) technologies have been successfully applied in various applications. Fused deposition modeling (FDM), one of the most popular AM techniques, is the most widely used method for fabricating thermoplastic parts those are mainly used as rapid prototypes for functional testing with advantages of low cost, minimal wastage, and ease of material change. Due to the intrinsically limited mechanical properties of pure thermoplastic materials, there is a critical need to improve mechanical properties for FDM-fabricated pure thermoplastic parts. One of the possible methods is adding reinforced materials (such as carbon fibers) into plastic materials to form thermoplastic matrix carbon fiber reinforced plastic (CFRP) composites those could be directly used in the actual application areas, such as aerospace, automotive, and wind energy. This paper is going to present FDM of thermoplastic matrix CFRP composites and test if adding carbon fiber (different content and length) can improve the mechanical properties of FDM-fabricated parts. The CFRP feedstock filaments were fabricated from plastic pellets and carbon fiber powders for FDM process. After FDM fabrication, effects on the tensile properties (including tensile strength, Young's modulus, toughness, yield strength, and ductility) and flexural properties (including flexural stress, flexural modulus, flexural toughness, and flexural yield strength) of specimens were experimentally investigated. In order to explore the parts fracture reasons during tensile and flexural tests, fracture interface of CFRP composite specimens after tensile testing and flexural testing was observed and analyzed using SEM micrograph.

The Mechanical Design of Nacre

Abstract: Mother-of-pearl (nacre) is a platelet-reinforced composite, highly filled with calcium carbonate (aragonite). The Young modulus, determined from beams of a span-to-depth ratio of no less than 15 (a necessary precaution), is of the order of 70 GPa (dry) and 60 GPa (wet), much higher than previously recorded values. These values can be derived from ‘shear-lag’ models developed for platey composites, suggesting that nacre is a near-ideal material. The tensile strength of nacre is of the order of 170 MPa (dry) and 140 MPa (wet), values which are best modelled assuming that pull-out of the platelets is the main mode of failure. In three-point bending, depending on the span-to-depth ratio and degree of hydration, the work to fracture across the platelets varies from 350 to 1240 J m -2 . In general, the effect of water is to increase the ductility of nacre and increase the toughness almost tenfold by the associated introduction of plastic work. The pull-out model is sufficient to account for the toughness of dry nacre, but accounts for only a third of the toughness of wet nacre. The additional contribution probably comes from debonding within the thin layer of matrix material. Electron microscopy reveals that the ductility of wet nacre is caused by cohesive fracture along platelet lamellae at right angles to the main crack. The matrix appears to be well bonded to the lamellae, enabling the matrix to be stretched across the delamination cracks without breaking, thereby sustaining a force across a wider crack. Such a mechanism also explains why toughness is dependent on the span-to-depth ratio of the test piece. With this last observation as a possible exception, nacre does not employ any really novel mechanisms to achieve its mechanical properties. It is simply ‘well made’. The importance of nacre to the mollusc depends both on the material and the size of the shell. Catastrophic failure will be very likely in whole, undamaged shells which behave like unnotched beams at large span-to-depth ratios. This tendency is increased by the fact that predators act as ‘soft’ machines and store strain energy which can be fed into the material very quickly once the fracture stress has been reached. It may therefore be advantageous to have a shell made of an intrinsically less tough material which is better at stopping cracks (e. g. crossed lamellar). However, nacre may still be preferred for the short, thick shells of young molluscs, as these have a low span-to-depth ratio and can make better use of ductility mechanisms.

Twinning and the ductility of magnesium alloys Part I: “Tension” twins

Abstract: Magnesium and its alloys do not in general undergo the same extended range of plasticity as their competitor structural metals. The present work is part I of a study that examines some of the roles deformation twinning might play in the phenomenon. A series of tensile test results are reported for the common wrought alloy AZ31. These data are employed in conjunction with a simple constitutive model to argue that View the MathML source twinning (which gives extension along the c-axis) can increase the uniform elongation in tensile tests. This effect appears to be similar to that seen in Ti, Zr and Cu–Si and in the so called TWIP phenomenon in steel.

Heterogeneous lamella structure unites ultrafine-grain strength with coarse-grain ductility.

Abstract: Grain refinement can make conventional metals several times stronger, but this comes at dramatic loss of ductility. Here we report a heterogeneous lamella structure in Ti produced by asymmetric rolling and partial recrystallization that can produce an unprecedented property combination: as strong as ultrafine-grained metal and at the same time as ductile as conventional coarse-grained metal. It also has higher strain hardening than coarse-grained Ti, which was hitherto believed impossible. The heterogeneous lamella structure is characterized with soft micrograined lamellae embedded in hard ultrafine-grained lamella matrix. The unusual high strength is obtained with the assistance of high back stress developed from heterogeneous yielding, whereas the high ductility is attributed to back-stress hardening and dislocation hardening. The process discovered here is amenable to large-scale industrial production at low cost, and might be applicable to other metal systems.

Mechanical biocompatibilities of titanium alloys for biomedical applications.

Abstract: Young's modulus as well as tensile strength, ductility, fatigue life, fretting fatigue life, wear properties, functionalities, etc., should be adjusted to levels that are suitable for structural biomaterials used in implants that replace hard tissue. These factors may be collectively referred to as mechanical biocompatibilities. In this paper, the following are described with regard to biomedical applications of titanium alloys: the Young's modulus, wear properties, notch fatigue strength, fatigue behaviour on relation to ageing treatment, improvement of fatigue strength, fatigue crack propagation resistance and ductility by the deformation-induced martensitic transformation of the unstable beta phase, and multifunctional deformation behaviours of titanium alloys.