Showing papers on "Field-effect transistor published in 2004"

Elastomeric Transistor Stamps: Reversible Probing of Charge Transport in Organic Crystals

Abstract: We introduce a method to fabricate high-performance field-effect transistors on the surface of freestanding organic single crystals. The transistors are constructed by laminating a monolithic elastomeric transistor stamp against the surface of a crystal. This method, which eliminates exposure of the fragile organic surface to the hazards of conventional processing, enables fabrication of rubrene transistors with charge carrier mobilities as high as approximately 15 cm2/V.s and subthreshold slopes as low as 2nF.V/decade.cm2. Multiple relamination of the transistor stamp against the same crystal does not affect the transistor characteristics; we exploit this reversibility to reveal anisotropic charge transport at the basal plane of rubrene.

Extraordinary Mobility in Semiconducting Carbon Nanotubes

Abstract: Semiconducting carbon nanotube transistors with channel lengths exceeding 300 microns have been fabricated. In these long transistors, carrier transport is diffusive and the channel resistance dominates the transport. Transport characteristics are used to extract the field-effect mobility (79 000 cm2/Vs) and estimate the intrinsic mobility (>100 000 cm2/Vs) at room temperature. These values exceed those for all known semiconductors, which bodes well for application of nanotubes in high-speed transistors, single- and few-electron memories, and chemical/biochemical sensors.

Gate Insulators in Organic Field-Effect Transistors

Abstract: In this paper, we review recent progress in the understanding of insulator/semiconductor interfaces in organic field-effect transistors (OFETs). We would like to emphasize that the choice of gate insulator is as important for high-quality OFET devices as the semiconductor itself, especially because of the unique transport mechanisms operating in them. To date researchers have explored numerous organic and inorganic insulator materials, some of them designed to improve the morphology of the organic semiconductor (OSC). Surface treatments, particularly on inorganic insulators, have been shown to influence significantly molecular ordering and device performance. In addition, the deposition technique used for the insulator and semiconductor layers has a further impact on the active interface. Dielectric related effects are reviewed here for a variety of polymeric and molecular semiconductors reported in the literature, with an emphasis on electronic transport. We also review in more detail experiences at Phil...

Band-to-band tunneling in carbon nanotube field-effect transistors.

Abstract: A detailed study on the mechanism of band-to-band tunneling in carbon nanotube field-effect transistors (CNFETs) is presented. Through a dual-gated CNFET structure tunneling currents from the valence into the conduction band and vice versa can be enabled or disabled by changing the gate potential. Different from a conventional device where the Fermi distribution ultimately limits the gate voltage range for switching the device on or off, current flow is controlled here by the valence and conduction band edges in a bandpass-filter-like arrangement. We discuss how the structure of the nanotube is the key enabler of this particular one-dimensional tunneling effect.

Control of carrier density by self-assembled monolayers in organic field-effect transistors

Abstract: Organic thin-film transistors are attracting a great deal of attention due to the relatively high field-effect mobility in several organic materials. In these organic semiconductors, however, researchers have not established a reliable method of doping at a very low density level, although this has been crucial for the technological development of inorganic semiconductors. In the field-effect device structures, the conduction channel exists at the interface between organic thin films and SiO2 gate insulators. Here, we discuss a new technique that enables us to control the charge density in the channel by using organosilane self-assembled monolayers (SAMs) on SiO2 gate insulators. SAMs with fluorine and amino groups have been shown to accumulate holes and electrons, respectively, in the transistor channel: these properties are understood in terms of the effects of electric dipoles of the SAMs molecules, and weak charge transfer between organic films and SAMs.

ZnO nanowire field-effect transistor and oxygen sensing property

Abstract: Single-crystal ZnO nanowires are synthesized using a vapor trapping chemical vapor deposition method and configured as field-effect transistors. Electrical transport studies show n-type semiconducting behavior with a carrier concentration of ∼107cm−1 and an electron mobility of ∼17cm2∕Vs. The contact Schottky barrier between the Au/Ni electrode and nanowire is determined from the temperature dependence of the conductance. Thermionic emission is found to dominate the transport mechanism. The effect of oxygen adsorption on electron transport through the nanowires is investigated. The sensitivity to oxygen is demonstrated to be higher with smaller radii nanowires. Moreover, the oxygen detection sensitivity can be modulated by the gate voltage. These results indicate that ZnO holds high potential for nanoscale sensing applications.

Low-voltage organic transistors with an amorphous molecular gate dielectric

Abstract: Organic thin film transistors (TFTs) are of interest for a variety of large-area electronic applications, such as displays, sensors and electronic barcodes. One of the key problems with existing organic TFTs is their large operating voltage, which often exceeds 20 V. This is due to poor capacitive coupling through relatively thick gate dielectric layers: these dielectrics are usually either inorganic oxides or nitrides, or insulating polymers, and are often thicker than 100 nm to minimize gate leakage currents. Here we demonstrate a manufacturing process for TFTs with a 2.5-nm-thick molecular self-assembled monolayer (SAM) gate dielectric and a high-mobility organic semiconductor (pentacene). These TFTs operate with supply voltages of less than 2 V, yet have gate currents that are lower than those of advanced silicon field-effect transistors with SiO2 dielectrics. These results should therefore increase the prospects of using organic TFTs in low-power applications (such as portable devices). Moreover, molecular SAMs may even be of interest for advanced silicon transistors where the continued reduction in dielectric thickness leads to ever greater gate leakage and power dissipation.

Single Crystal Nanowire Vertical Surround-Gate Field-Effect Transistor

Abstract: Harnessing the potential of single crystal inorganic nanowires for practical advanced nanoscale applications requires not only reproducible synthesis of highly regular one-dimensional (1D) nanowire arrays directly on device platforms but also elegant device integration which retains structural integrity of the nanowires while significantly reducing or eliminating complex critical processing steps. Here we demonstrate a unique, direct, and bottom-up integration of a semiconductor 1D nanowire, using zinc oxide (ZnO) as an example, to obtain a vertical surround-gate field-effect transistor (VSG-FET). The vertical device structure and bottom-up integration reduce process complexity, compared to conventional top-down approaches. More significantly, scaling of the vertical channel length is lithographically independent and decoupled from the device packing density. A bottom electrical contact to the nanowire is uniquely provided by a heavily doped underlying lattice-match substrate. Based on the nanowire-integrated platform, both n- and p-channel VSG-FETs are fabricated. The vertical device architecture has the potential for use in tera-level ultrahigh-density nanoscale memory and logic devices.

Carbon Nanotube Field-Effect Transistors with Integrated Ohmic Contacts and High-κ Gate Dielectrics

Abstract: High-performance enhancement-mode semiconducting carbon nanotube field-effect transistors (CNTFETs) are obtained by combining ohmic metal-tube contacts, high-dielectric-constant HfO2 films as gate insulators, and electrostatically doped nanotube segments as source/drain electrodes. The combination of these elements affords high ON currents and subthreshold swings of 70-80 mV/decade and allows for low OFF currents and suppressed ambipolar conduction. The doped source and drain approach resembles that of MOSFETs and can impart excellent OFF states to nanotube FETs under aggressive vertical scaling. This presents an important advantage over devices with a metal source/drain, or devices commonly referred to as Schottky barrier FETs.

Spatially correlated charge transport in organic thin film transistors

Abstract: Hole mobility in organic ultrathin film field-effect transistors is studied as a function of the coverage. For layered sexithienyl films, the charge carrier mobility rapidly increases with increasing coverage and saturates at a coverage of about two monolayers. This shows that the first two molecular layers next to the dielectric interface dominate the charge transport. A quantitative analysis of spatial correlations shows that the second layer is crucial, as it provides efficient percolation pathways for carriers generated in both the first and the second layers. The upper layers do not actively contribute either because their domains are smaller than the ones in the second layer or because the carrier density is negligible.

High-mobility field-effect transistors based on transition metal dichalcogenides

Abstract: We report on fabrication of field-effect transistors (FETs) based on transition metal dichalcogenides. The unique structure of single crystals of these layered inorganic semiconductors enables fabrication of FETs with intrinsically low field-effect threshold and high charge carrier mobility, comparable to that in the best single-crystal Si FETs (up to 500 cm2/V s for the p-type conductivity in the WSe2-based FETs at room temperature). These FETs demonstrate ambipolar operation. Owing to mechanical flexibility, they hold potential for applications in “flexible” electronics.

Organic single-crystal field-effect transistors

Abstract: Organic electronics constitute an innovative field, with interesting applications complementary to the silicon semiconductor technology. From a scientific perspective, there is large interest in the fundamental understanding of electrical transport in organic semiconductors. However, a well-developed microscopic description is still lacking, due to the complicated character of the many-body polaronic-type of charge carriers in molecular compounds. In this Thesis, we have experimentally studied the intrinsic charge transport properties of organic semiconductors by using organic single-crystal field-effect transistors. The electric field-effect has been frequently used to investigate thin films of organic compounds. Unfortunately, thin-film transistors are not suitable for the study of intrinsic electronic properties of organic conductors, because their characteristics are often strongly affected by imperfections of the film structure and by insufficient purity of organic materials. Thus, for a higher degree of molecular ordering and an improved quality of the FET, we fabricate devices on the surface of a free-standing single crystal of organic molecules. In short, in this work we have achieved successful fabrication of high-quality single-crystal FETs, exhibiting high mobilities and signs of intrinsic transport. Herewith, we have identified new aspects that influence charge transport in organic semiconductor FETs, and we have performed exploratory measurements in the charge density regime approaching one carrier per molecule.

Self-Aligned Ballistic Molecular Transistors and Electrically Parallel Nanotube Arrays

Abstract: Carbon nanotube field-effect transistors with structures and properties near the scaling limit with short (down to 50 nm) channels, self-aligned geometries, palladium electrodes with low contact resistance, and high-K dielectric gate insulators are realized. Electrical transport in these miniature transistors is nearly ballistic up to high biases at both room and low temperatures. Atomic-layer-deposited (ALD) high-K films interact with nanotube sidewalls via van der Waals interactions without causing weak localization at 4 K. New fundamental understanding of ballistic transport, optical phonon scattering, and potential interfacial scattering mechanisms in nanotubes is obtained. Also, parallel arrays of such molecular transistors are enabled to deliver macroscopic currents-an important milestone for future circuit applications.

Threshold voltage shift in organic field effect transistors by dipole monolayers on the gate insulator

Abstract: We demonstrate controllable shift of the threshold voltage and the turn-on voltage in pentacene thin film transistors and rubrene single crystal field effect transistors (FET) by the use of nine organosilanes with different functional groups. Prior to depositing the organic semiconductors, the organosilanes were applied to the SiO2 gate insulator from solution and form a self-assembled monolayer (SAM). The observed shifts of the transfer characteristics range from −2to50V and can be related to the surface potential of the layer next to the transistor channel. Concomitantly the mobile charge carrier concentration at zero gate bias reaches up to 4×1012∕cm2. In the single crystal FETs the measured transfer characteristics are also shifted, while essentially maintaining the high quality of the subthreshold swing. The shift of the transfer characteristics is governed by the built-in electric field of the SAM and can be explained using a simple energy level diagram. In the thin film devices, the subthreshold re...

Threshold Voltage Shift in Organic Field Effect Transistors by Dipole-Monolayers on the Gate Insulator

Abstract: We demonstrate controllable shift of the threshold voltage and the turn-on voltage in pentacene thin film transistors and rubrene single crystal field effect transistors (FET) by the use of nine organosilanes with different functional groups. Prior to depositing the organic semiconductors, the organosilanes were applied to the SiO2 gate insulator from solution and form a self assembled monolayer (SAM). The observed shift of the transfer characteristics range from -2 to 50 V and can be related to the surface potential of the layer next to the transistor channel. Concomitantly the mobile charge carrier concentration at zero gate bias reaches up to 4*10^12/cm^2. In the single crystal FETs the measured transfer characteristics are also shifted, while essentially maintaining the high quality of the subthreshold swing. The shift of the transfer characteristics is governed by the built-in electric field of the SAM and can be explained using a simple energy level diagram. In the thin film devices, the subthreshold region is broadened, indicating that the SAM creates additional trap states, whose density is estimated to be of order 1*10^12/cm^2.

Novel High-Mobility Field-Effect Transistors Based on Transition Metal Dichalcogenides

Abstract: We report on fabrication of novel field-effect transistors (FETs) based on transition metal dichalcogenides. The unique structure of single crystals of these layered inorganic semiconductors enables fabrication of FETs with intrinsically low field-effect threshold and high charge carrier mobility, comparable to that in the best single-crystal Si FETs (up to 500 cm2/Vs for the p-type conductivity in the WSe2-based FETs at room temperature). These novel FETs demonstrate ambipolar operation. Owing to mechanical flexibility, they hold potential for applications in "flexible" electronics.

Ion Transport in Nanofluidic Channels

Abstract: Theoretical modeling of ionic distribution and transport in silica nanotubes, 30 nm in diameter and 5 μm long, suggest that when the diameter is smaller than the Debye length, a unipolar solution of counterions is created within the nanotube and the colons are electrostatically repelled By locally modifying the surface charge density through a gate electrode, the ion concentration can be depleted under the gate and the ionic current can be significantly suppressed It is proposed that this could form the basis of a unipolar ionic field-effect transistor

Complementary tunneling transistor for low power application

Abstract: The metal oxide semiconductor field effect transistor (MOSFET) is scaling to a “tunneling epoch”, in which multiple leakage current induced by different tunneling effects exist. The complementary Si-based tunneling transistors are presented in this paper. The working principle of this device is investigated in detail. It is found that the band-to-band tunneling current is be controlled by the gate-to-source voltage. Due to the reverse biased p-i-n diode structure, an ultra-low leakage current is achieved. The sub-threshold swing of TFET is not limited by kt/q, which is the physical limit of the MOSFET. Using the CMOS compatible processes, the complementary TFETs (CTFET) are fabricated on one wafer. From a circuit point of view, the compatibility between TFET and MOSFET enables the transfer of CMOS circuits to CTFET circuits.

A spin metal–oxide–semiconductor field-effect transistor using half-metallic-ferromagnet contacts for the source and drain

Abstract: We propose and theoretically analyze a metal–oxide–semiconductor field-effect-transistor (MOSFET) type of spin transistor (spin MOSFET) consisting of a MOS structure and half-metallic-ferromagnet (HMF) contacts for the source and drain. When the magnetization configuration of the HMF source and drain is parallel (antiparallel), highly spin-polarized carriers injected from the HMF source to the channel are transported into (blocked by) the HMF drain, resulting in the magnetization-configuration-dependent output characteristics. Our two-dimensional numerical analysis indicates that the spin MOSFET exhibits high (low) current drive capability in the parallel (antiparallel) magnetization, and that extremely large magnetocurrent ratios can be obtained. Furthermore, the spin MOSFET satisfies other important requirements for “spintronic integrated circuits,” such as high amplification capability, low power-delay product, and low off-current.

Fabrication and electrical characteristics of high-performance ZnO nanorod field-effect transistors

Abstract: We report on fabrication and electrical characteristics of high-mobility field-effect transistors (FETs) using ZnO nanorods. For FET fabrications, single-crystal ZnO nanorods were prepared using catalyst-free metalorganic vapor phase epitaxy. Although typical ZnO nanorod FETs exhibited good electrical characteristics, with a transconductance of ∼140nS and a mobility of 75cm2∕Vs, the device characteristics were significantly improved by coating a polyimide thin layer on the nanorod surface, exhibiting a large turn-ON/OFF ratio of 104–105, a high transconductance of 1.9μS, and high electron mobility above 1000cm2∕Vs. The role of the polymer coating in the enhancement of the devices is also discussed.

Oxygen sensing characteristics of individual ZnO nanowire transistors

Abstract: Individual ZnO nanowire transistors are fabricated, and their sensing properties are investigated. The transistors show a carrier density of 2300μm−1 and mobility up to 6.4cm2∕Vs, which are obtained from the ISD−VG curves. The threshold voltage shifts in the positive direction and the source-drain current decreases as ambient oxygen concentration increases. However, the opposite occurs when the transistors are under illumination. Surface adsorbates on the ZnO nanowires affect both the mobility and the carrier density. Our data are helpful in understanding the sensing mechanism of the gas sensors.

A three-dimensional quantum simulation of silicon nanowire transistors with the effective-mass approximation

Abstract: The silicon nanowire transistor (SNWT) is a promising device structure for future integrated circuits, and simulations will be important for understanding its device physics and assessing its ultimate performance limits. In this work, we present a three-dimensional (3D) quantum mechanical simulation approach to treat various SNWTs within the effective-mass approximation. We begin by assuming ballistic transport, which gives the upper performance limit of the devices. The use of a mode space approach (either coupled or uncoupled) produces high computational efficiency that makes our 3D quantum simulator practical for extensive device simulation and design. Scattering in SNWTs is then treated by a simple model that uses so-called Buttiker probes, which was previously used in metal-oxide-semiconductor field effect transistor simulations. Using this simple approach, the effects of scattering on both internal device characteristics and terminal currents can be examined, which enables our simulator to be used f...

A Three-Dimensional Quantum Simulation of Silicon Nanowire Transistors with the Effective-Mass Approximation

Abstract: The silicon nanowire transistor (SNWT) is a promising device structure for future integrated circuits, and simulations will be important for understanding its device physics and assessing its ultimate performance limits. In this work, we present a three-dimensional quantum mechanical simulation approach to treat various SNWTs within the effective-mass approximation. We begin by assuming ballistic transport, which gives the upper performance limit of the devices. The use of a mode space approach (either coupled or uncoupled) produces high computational efficiency that makes our 3D quantum simulator practical for extensive device simulation and design. Scattering in SNWTs is then treated by a simple model that uses so-called Buttiker probes, which was previously used in metal-oxide-semiconductor field effect transistor (MOSFET) simulations. Using this simple approach, the effects of scattering on both internal device characteristics and terminal currents can be examined, which enables our simulator to be used for the exploration of realistic performance limits of SNWTs.

Building Blocks for n-Type Molecular and Polymeric Electronics. Perfluoroalkyl- versus Alkyl-Functionalized Oligothiophenes (nT; n = 2−6). Systematics of Thin Film Microstructure, Semiconductor Performance, and Modeling of Majority Charge Injection in Field-Effect Transistors

Abstract: The solid-state properties and FET electrical behavior of several series of α,ω- and β,β‘-fluorocarbon- and alkyl-substituted and unsubstituted oligothiophenes nTs (n = 2−6) are compared and contrasted. The thin films were grown by slow vacuum deposition over a range of substrate temperatures and/or by casting from solution and were investigated by X-ray diffraction and scanning electron microscopy. Our results indicate that vacuum deposition at 60−80 °C affords films with remarkably similar microstructures despite the extensive H → F substitution. Trends in observed d spacing versus molecular core extension provide quantitative information on molecular orientation. Field-effect transistor measurements performed for all systems and having the same device structure, components, and fabrication conditions demonstrate that all nTs functionalized with fluorocarbon chains at the thiophene termini are n-type semiconductors, in contrast to the p-type activity of the remaining systems. One of these systems, α,ω-d...

Plasma wave detection of sub-terahertz and terahertz radiation by silicon field-effect transistors

Abstract: We report on experiments on photoresponse to sub-THz (120GHz) radiation of Si field-effect transistors (FETs) with nanometer and submicron gate lengths at 300K. The observed photoresponse is in agreement with predictions of the Dyakonov–Shur plasma wave detection theory. This is experimental evidence of the plasma wave detection by silicon FETs. The plasma wave parameters deduced from the experiments allow us to predict the nonresonant and resonant detection in THz range by nanometer size silicon devices—operating at room temperature.

Highly linear receiver front-end adopting MOSFET transconductance linearization by multiple gated transistors

Abstract: Highly linear receiver RF front-end adopting MOSFET transconductance linearization by linearly superposing several common-source FET transistors in parallel (multiple gated transistor, or MGTR), combined with some additional circuit techniques are reported. In MGTR circuitry, linearity is improved by using transconductance linearization which can be achieved by canceling the negative peak value of g/sub m/'' of the main transistor with the positive one in the auxiliary transistor having a different size and gate drive combined in parallel. This enhancement, however, is limited by the distortion originated from the combined influence of g/sub m/' and harmonic feedback, which can greatly be reduced by the cascoding MGTR output for the amplifier and by the tuned load for the mixer. Experimental results designed using the above techniques show IIP/sub 3/ improvements at given power consumption by as much as 10 dB for CMOS low-noise amplifier at 900 MHz and 7 dB for Gilbert cell mixer at 2.4 GHz without sacrificing other features such as gain and noise figure.

A numerical study of scaling issues for Schottky-barrier carbon nanotube transistors

Abstract: We performed a comprehensive scaling study of Schottky-barrier (SB) carbon nanotube transistors using self-consistent, atomistic scale simulations. We restrict our attention to SB carbon nanotube field-effect transistors (FETs) whose metal source-drain is attached to an intrinsic carbon nanotube channel. Ambipolar conduction is found to be an important factor that must be carefully considered in device design, especially when the gate oxide is thin. The channel length scaling limit imposed by source-drain tunneling is found to be between 5 nm and 10 nm, depending on the off-current specification. Using a large diameter tube increases the on-current, but it also increases the leakage current. Our study of gate dielectric scaling shows that the charge on the nanotube can play an important role above threshold.

High mobility of dithiophene-tetrathiafulvalene single-crystal organic field effect transistors.

Abstract: Single-crystal field effect transistors of the organic semiconductor dithiophene-tetrathiafulvalene (DT-TTF) were prepared by drop casting. Long, thin crystals connected two microfabricated gold electrodes, and a silicon substrate was used as a back gate. The highest hole mobility observed was 1.4 cm2/Vs, which is the highest reported for an organic semiconductor not based on pentacene. A high ON/OFF ratio of at least 7 x 105 was obtained for this device.