Topic
Gas metal arc welding
About: Gas metal arc welding is a research topic. Over the lifetime, 11706 publications have been published within this topic receiving 109555 citations. The topic is also known as: metal active gas welding & GMAW.
Papers published on a yearly basis
Papers
More filters
Patent•
[...]
05 Jun 1969
TL;DR: In this paper, a high current capacity arc welding gun for gas-shielded, continuous feed, consumable electrode arc welding processes is presented, which includes: a unique handle cooled by convection air flow; an improved head assembly having a unique electrical insulating ion impervious shield for preventing destructive arcing to the gas nozzle, an improved shielding gas flow path through the head assembly which additionally cooperates with the ion-resistant shield to prevent gas nozzle arcing, a unique current contact tip which attaches to head assembly by a novel curved wedge clamping concept and which is produced
Abstract: A high current capacity arc welding gun for gas-shielded, continuous feed, consumable electrode arc welding processes. Features include: a unique handle cooled by convection air flow; an improved head assembly having a unique electrical insulating ion impervious shield for preventing destructive arcing to the gas nozzle, an improved shielding gas flow path through the head assembly which additionally cooperates with the ion impervious shield to prevent gas nozzle arcing, a unique current contact tip which attaches to the head assembly by a novel curved wedge clamping concept and which is produced by an improved, versatile, and inexpensive method of manufacture that increases the copper density and refines the grain structure in the current contact tip for greater life; an improved gooseneck lining for longer life and reduced friction; a heat protected control switch assembly of rugged construction and unique trigger operation; and an improved welding cable connection assembly.
129 citations
17 Apr 2015-Materials Science and Engineering A-structural Materials Properties Microstructure and Processing
TL;DR: In this article, the additive layer manufacturing (ALM) process is used to produce full density titanium aluminide components directly using the new additive layer additive manufacturing method, and the microstructure variation and strengthening mechanisms resulting from the new manufacturing approach are analysed in detail.
Abstract: An innovative and low cost additive layer manufacturing (ALM) process is used to produce γ-TiAl based alloy wall components. Gas tungsten arc welding (GTAW) provides the heat source for this new approach, combined with in-situ alloying through separate feeding of commercially pure Ti and Al wires into the weld pool. This paper investigates the morphology, microstructure and mechanical properties of the additively manufactured TiAl material, and how these are affected by the location within the manufactured component. The typical additively layer manufactured morphology exhibits epitaxial growth of columnar grains and several layer bands. The fabricated γ-TiAl based alloy consists of comparatively large α 2 grains in the near-substrate region, fully lamellar colonies with various sizes and interdendritic γ structure in the intermediate layer bands, followed by fine dendrites and interdendritic γ phases in the top region. Microhardness measurements and tensile testing results indicated relatively homogeneous mechanical characteristics throughout the deposited material. The exception to this homogeneity occurs in the near-substrate region immediately adjacent to the pure Ti substrate used in these experiments, where the alloying process is not as well controlled as in the higher regions. The tensile properties are also different for the vertical (build) direction and horizontal (travel) direction because of the differing microstructure in each direction. The microstructure variation and strengthening mechanisms resulting from the new manufacturing approach are analysed in detail. The results demonstrate the potential to produce full density titanium aluminide components directly using the new additive layer manufacturing method.
129 citations
TL;DR: In this article, the effect of vacuum on weld penetration and porosity formation was investigated in high-power cw CO2 and YAG laser welding, and it was shown that no porosity was present in the materials welded at lower pressures.
Abstract: The effect of vacuum on weld penetration and porosity formation was investigated in high-power cw CO2 and YAG laser welding. It was consequently confirmed in welding with both lasers that the penetration was slightly deeper in aluminum alloys and austenitic stainless steel with a decrease in the ambient pressure. It was also revealed that no porosity was present in the materials welded at lower pressures. The reason for no porosity formation in vacuum was examined by observing keyhole behavior, bubble and porosity formation situation, and liquid flow in the molten pool during high-power YAG laser welding under various conditions through the microfocused x-ray real-time observation system. It was confirmed in the coaxial Ar or He shielding gas that a lot of bubbles were generated near the bottom part of the molten pool from the tip of a fluctuated keyhole and resulted in large pores. On the other hand, under the vacuum conditions, no bubbles were formed in the melt pool from the keyhole, although the middl...
126 citations
TL;DR: In this article, a rugged, low-cost, point infrared sensor was used to monitor changes in the plate surface temperatures occurring during the welding process to eliminate or mitigate defects that may form due to the process perturbations.
125 citations
TL;DR: The shrinkage volume method as discussed by the authors is a linear elastic finite-element modeling technique that has been developed to predict post-weld distortion and residual stress in a carbon steel plate with different vee-butt preparations.
124 citations