scispace - formally typeset
Search or ask a question
Topic

Ionic conductivity

About: Ionic conductivity is a research topic. Over the lifetime, 19412 publications have been published within this topic receiving 519167 citations.


Papers
More filters
Journal ArticleDOI
TL;DR: This work provides a simple and effective strategy to develop low-T AABs by using dimethyl sulfoxide (DMSO) as an additive with the molar fraction of 0.3 and reveals that the hydrogen bonds are stably formed between DMSO and water molecules and this is taking the role for the electrolyte working at an ultra-low-T.
Abstract: Insufficient ionic conductivity and freezing of the electrolyte are considered the main problems for electrochemical energy storage at low temperatures (low T). Here, an electrolyte with a freezing point lower than -130 °C is developed by using dimethyl sulfoxide (DMSO) as an additive with molar fraction of 0.3 to an aqueous solution of 2 m NaClO4 (2M-0.3 electrolyte). The 2M-0.3 electrolyte exhibits sufficient ionic conductivity of 0.11 mS cm-1 at -50 °C. The combination of spectroscopic investigations and molecular dynamics (MD) simulations reveal that hydrogen bonds are stably formed between DMSO and water molecules, facilitating the operation of the electrolyte at ultra-low T. Using DMSO as the electrolyte additive, the aqueous rechargeable alkali-ion batteries (AABs) can work well even at -50 °C. This work provides a simple and effective strategy to develop low T AABs.

226 citations

Journal ArticleDOI
TL;DR: Garnet-type solid state electrolyte is used as an interlayer between solid electrolyte and solid electrodes to improve their contact and reduce their interfacial resistance and the demonstrated hybrid battery presents a promising future for battery development with high energy and good safety.
Abstract: Garnet-type solid state electrolyte (SSE) is a promising candidate for high performance lithium (Li)-metal batteries due to its good stability and high ionic conductivity. One of the main challenges for garnet solid state batteries is the poor solid–solid contact between the garnet and electrodes, which results in high interfacial resistance, large polarizations, and low efficiencies in batteries. To address this challenge, in this work gel electrolyte is used as an interlayer between solid electrolyte and solid electrodes to improve their contact and reduce their interfacial resistance. The gel electrolyte has a soft structure, high ionic conductivity, and good wettability. Through construction of the garnet/gel interlayer/electrode structure, the interfacial resistance of the garnet significantly decreased from 6.5 × 104 to 248 Ω cm2 for the cathode and from 1.4 × 103 to 214 Ω cm2 for the Li-metal anode, successfully demonstrating a full cell with high capacity (140 mAh/g for LiFePO4 cathode) over 70 st...

226 citations

Journal ArticleDOI
TL;DR: In this paper, a 3D ordered bicontinuous conducting ceramic and insulating polymer microchannels were used to construct 3D scaffolds with 3D printed polymer template.
Abstract: Hybrid solid electrolytes, composed of 3D ordered bicontinuous conducting ceramic and insulating polymer microchannels are reported. The ceramic channels provide continuous, uninterrupted pathways, maintaining high ionic conductivity between the electrodes, while the polymer channels permit improvement of the mechanical properties from that of the ceramic alone, in particular mitigation of the ceramic brittleness. The conductivity of a ceramic electrolyte is usually limited by resistance at the grain boundaries, necessitating dense ceramics. The conductivity of the 3D ordered hybrid is reduced by only the volume fraction occupied by the ceramic, demonstrating that the ceramic channels can be sintered to high density similar to a dense ceramic disk. The hybrid electrolytes are demonstrated using the ceramic lithium ion conductor Li1.4Al0.4Ge1.6(PO4)3 (LAGP). Structured LAGP 3D scaffolds with empty channels were prepared by negative replication of a 3D printed polymer template. Filling the empty channels with non-conducting polypropylene (PP) or epoxy polymer (epoxy) creates the structured hybrid electrolytes with 3D bicontinuous ceramic and polymer microchannels. Printed templating permits precise control of the ceramic to polymer ratio and the microarchitecture; as demonstrated by the formation of cubic, gyroidal, diamond and spinodal (bijel) structures. The electrical and mechanical properties depend on the microarchitecture, the gyroid filled with epoxy giving the best combination of conductivity and mechanical properties. An ionic conductivity of 1.6 × 10−4 S cm−1 at room temperature was obtained, reduced from the conductivity of a sintered LAGP pellet only by the volume fraction occupied by the ceramic. The mechanical properties of the gyroid LAGP–epoxy electrolyte demonstrate up to 28% higher compressive failure strain and up to five times the flexural failure strain of a LAGP pellet before rupture. Notably, this demonstrates that ordered ceramic and polymer hybrid electrolytes can have superior mechanical properties without significantly compromising ionic conductivity, which addresses one of the key challenges for all-solid-state batteries.

226 citations

Journal ArticleDOI
TL;DR: Garnets are capable of accommodating an excess of lithium cations beyond that normally found in this prototypical structure and this excess lithium is found in a mixture of coordination environments with considerable positional and occupational disorder and leads to ionic conductivity of up to 4 × 10−4 S cm−1 at room temperature as discussed by the authors.
Abstract: Garnets are capable of accommodating an excess of lithium cations beyond that normally found in this prototypical structure. This excess lithium is found in a mixture of coordination environments with considerable positional and occupational disorder and leads to ionic conductivity of up to 4 × 10−4 S cm−1 at room temperature. This high value for total conductivity, combined with excellent thermal and (electro)chemical resistance makes these candidate materials for operation in all solid-state batteries. This review looks at garnets with a wide range of stoichiometries and lithium concentrations and the impact of complex lithium distributions and crystallographic order/disorder transitions on the transport properties of these materials.

225 citations

Journal ArticleDOI
TL;DR: In this article, the ionic conductivity of polymeric gel electrolyte membranes has been found to increase with increasing concentration of IL and attains a maximum value of 2 × 10−3 S cm−1 at 30 °C and ∼3 × 10 −2 S cm −1 at 130 °C.
Abstract: Ion conducting polymer gel electrolyte membranes based on polymer poly(vinylidene fluoride-co-hexafluoropropylene) PVdF-HFP, ionic liquid, 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide BMIMTFSI with and without the Li-salt (having the same anion i.e. the TFSI− anion) have been synthesized. Prepared membranes have been characterized by scanning electron microscopy, X-ray diffraction, Fourier transform infrared (FTIR), differential scanning calorimetry, thermogravimetric analysis (TGA) and complex impedance spectroscopic techniques. Incorporation of IL in the polymer PVdF-HFP/polymer electrolyte (i.e. PVdF-HFP + 20 wt% LiTFSI) changes different physicochemical properties such as melting temperature (Tm), glass transition temperature (Tg), thermal stability, degree of crystallinity (Xc), and ionic transport behaviour of these materials. The ionic conductivity of polymeric gel electrolyte membranes has been found to increase with increasing concentration of IL and attains a maximum value of 2 × 10−3 S cm−1 at 30 °C and ∼3 × 10−2 S cm−1 at 130 °C. A high total ionic transference number >0.99 and the cationic transference number (tLi+) ∼ 0.22 with a wider electrochemical window (ECW) ∼ 4.0–5.0 V for the polymer gel electrolyte membrane containing higher loading of IL (∼70 wt% of IL) have been obtained. Temperature dependent ionic conductivity obeys Arrhenius type thermally activated behaviour.

225 citations


Network Information
Related Topics (5)
Oxide
213.4K papers, 3.6M citations
89% related
Thin film
275.5K papers, 4.5M citations
86% related
Carbon nanotube
109K papers, 3.6M citations
86% related
Graphene
144.5K papers, 4.9M citations
86% related
Raman spectroscopy
122.6K papers, 2.8M citations
86% related
Performance
Metrics
No. of papers in the topic in previous years
YearPapers
20231,167
20222,073
20211,175
20201,117
20191,030
2018966