Laser beam quality

Abstract: Ultrahigh intensity lasers can potentially be used in conjunction with conventional fusion lasers to ignite inertial confinement fusion (ICF) capsules with a total energy of a few tens of kilojoules of laser light, and can possibly lead to high gain with as little as 100 kJ. A scheme is proposed with three phases. First, a capsule is imploded as in the conventional approach to inertial fusion to assemble a high‐density fuel configuration. Second, a hole is bored through the capsule corona composed of ablated material, as the critical density is pushed close to the high‐density core of the capsule by the ponderomotive force associated with high‐intensity laser light. Finally, the fuel is ignited by suprathermal electrons, produced in the high‐intensity laser–plasma interactions, which then propagate from critical density to this high‐density core. This new scheme also drastically reduces the difficulty of the implosion, and thereby allows lower quality fabrication and less stringent beam quality and symmet...

Abstract: We demonstrate the transfer of information encoded as orbital angular momentum (OAM) states of a light beam. The transmitter and receiver units are based on spatial light modulators, which prepare or measure a laser beam in one of eight pure OAM states. We show that the information encoded in this way is resistant to eavesdropping in the sense that any attempt to sample the beam away from its axis will be subject to an angular restriction and a lateral offset, both of which result in inherent uncertainty in the measurement. This gives an experimental insight into the effects of aperturing and misalignment of the beam on the OAMmeasurement and demonstrates the uncertainty relationship for OAM.

Abstract: Cylindrical-vector beams are of increasing recent interest for their role in novel laser resonators and their applications to electron acceleration and scanning microscopy. In this paper, we calculate cylindrical-vector fields, near the focal region of an aplanatic lens, and briefly discuss some applications. We show that, in the particular case of a tightly focused, radially polarized beam, the polarization shows large inhomogeneities in the focal region, while the azimuthally polarized beam is purely transverse even at very high numerical apertures.

Abstract: A protocol is prescribed for clinical reference dosimetry of external beam radiation therapy using photon beams with nominal energies between 60Co and 50 MV and electron beams with nominal energies between 4 and 50 MeV. The protocol was written by Task Group 51 (TG-51) of the Radiation Therapy Committee of the American Association of Physicists in Medicine (AAPM) and has been formally approved by the AAPM for clinical use. The protocol uses ion chambers with absorbed-dose-to-water calibration factors, N(60Co)D,w which are traceable to national primary standards, and the equation D(Q)w = MkQN(60Co)D,w where Q is the beam quality of the clinical beam, D(Q)w is the absorbed dose to water at the point of measurement of the ion chamber placed under reference conditions, M is the fully corrected ion chamber reading, and kQ is the quality conversion factor which converts the calibration factor for a 60Co beam to that for a beam of quality Q. Values of kQ are presented as a function of Q for many ion chambers. The value of M is given by M = PionP(TP)PelecPpolMraw, where Mraw is the raw, uncorrected ion chamber reading and Pion corrects for ion recombination, P(TP) for temperature and pressure variations, Pelec for inaccuracy of the electrometer if calibrated separately, and Ppol for chamber polarity effects. Beam quality, Q, is specified (i) for photon beams, by %dd(10)x, the photon component of the percentage depth dose at 10 cm depth for a field size of 10x10 cm2 on the surface of a phantom at an SSD of 100 cm and (ii) for electron beams, by R50, the depth at which the absorbed-dose falls to 50% of the maximum dose in a beam with field size > or =10x10 cm2 on the surface of the phantom (> or =20x20 cm2 for R50>8.5 cm) at an SSD of 100 cm. R50 is determined directly from the measured value of I50, the depth at which the ionization falls to 50% of its maximum value. All clinical reference dosimetry is performed in a water phantom. The reference depth for calibration purposes is 10 cm for photon beams and 0.6R50-0.1 cm for electron beams. For photon beams clinical reference dosimetry is performed in either an SSD or SAD setup with a 10x10 cm2 field size defined on the phantom surface for an SSD setup or at the depth of the detector for an SAD setup. For electron beams clinical reference dosimetry is performed with a field size of > or =10x10 cm2 (> or =20x20 cm2 for R50>8.5 cm) at an SSD between 90 and 110 cm. This protocol represents a major simplification compared to the AAPM's TG-21 protocol in the sense that large tables of stopping-power ratios and mass-energy absorption coefficients are not needed and the user does not need to calculate any theoretical dosimetry factors. Worksheets for various situations are presented along with a list of equipment required.

Abstract: We demonstrate experimentally that a spiral phaseplate can convert a TEM00 laser beam into a helical-wavefront beam with a phase singularity at its axis. The diffractive-optical effect of the spiral phaseplate is implemented by index matching a macroscopic structure in an optical immersion. We discuss the optical properties of a helical wavefront beam produced this way by means of a mode analysis and by Fraunhofer diffraction calculations.