Showing papers on "Maximum power point tracking published in 2009"

Comprehensive Approach to Modeling and Simulation of Photovoltaic Arrays

Abstract: This paper proposes a method of modeling and simulation of photovoltaic arrays. The main objective is to find the parameters of the nonlinear I-V equation by adjusting the curve at three points: open circuit, maximum power, and short circuit. Given these three points, which are provided by all commercial array data sheets, the method finds the best I-V equation for the single-diode photovoltaic (PV) model including the effect of the series and parallel resistances, and warranties that the maximum power of the model matches with the maximum power of the real array. With the parameters of the adjusted I-V equation, one can build a PV circuit model with any circuit simulator by using basic math blocks. The modeling method and the proposed circuit model are useful for power electronics designers who need a simple, fast, accurate, and easy-to-use modeling method for using in simulations of PV systems. In the first pages, the reader will find a tutorial on PV devices and will understand the parameters that compose the single-diode PV model. The modeling method is then introduced and presented in details. The model is validated with experimental data of commercial PV arrays.

Control of a Single-Phase Cascaded H-Bridge Multilevel Inverter for Grid-Connected Photovoltaic Systems

Abstract: This paper presents a single-phase cascaded H-bridge converter for a grid-connected photovoltaic (PV) application The multilevel topology consists of several H-bridge cells connected in series, each one connected to a string of PV modules The adopted control scheme permits the independent control of each dc-link voltage, enabling, in this way, the tracking of the maximum power point for each string of PV panels Additionally, low-ripple sinusoidal-current waveforms are generated with almost unity power factor The topology offers other advantages such as the operation at lower switching frequency or lower current ripple compared to standard two-level topologies Simulation and experimental results are presented for different operating conditions

Multilevel Inverter For Grid-Connected PV System Employing Digital PI Controller

Abstract: This paper presents a single-phase five-level photovoltaic (PV) inverter topology for grid-connected PV systems with a novel pulsewidth-modulated (PWM) control scheme. Two reference signals identical to each other with an offset equivalent to the amplitude of the triangular carrier signal were used to generate PWM signals for the switches. A digital proportional-integral current control algorithm is implemented in DSP TMS320F2812 to keep the current injected into the grid sinusoidal and to have high dynamic performance with rapidly changing atmospheric conditions. The inverter offers much less total harmonic distortion and can operate at near-unity power factor. The proposed system is verified through simulation and is implemented in a prototype, and the experimental results are compared with that with the conventional single-phase three-level grid-connected PWM inverter.

Electrical PV Array Reconfiguration Strategy for Energy Extraction Improvement in Grid-Connected PV Systems

Abstract: This paper applies a dynamical electrical array reconfiguration (EAR) strategy on the photovoltaic (PV) generator of a grid-connected PV system based on a plant-oriented configuration, in order to improve its energy production when the operating conditions of the solar panels are different. The EAR strategy is carried out by inserting a controllable switching matrix between the PV generator and the central inverter, which allows the electrical reconnection of the available PV modules. As a result, the PV system exhibits a self-capacity for real-time adaptation to the PV generator external operating conditions and improves the energy extraction of the system. Experimental results are provided to validate the proposed approach.

Parallel-Connected Solar PV System to Address Partial and Rapidly Fluctuating Shadow Conditions

Abstract: Solar photovoltaic (PV) arrays in portable applications are often subject to partial shading and rapid fluctuations of shading. In the usual series-connected wiring scheme, the residual energy generated by partially shaded cells either cannot be collected (if diode bypassed) or, worse, impedes collection of power from the remaining fully illuminated cells (if not bypassed). Rapid fluctuation of the shading pattern makes maximum power point (MPP) tracking difficult; generally, there will exist multiple local MPPs, and their values will change as rapidly as does the illumination. In this paper, a portable solar PV system that effectively eliminates both of the aforementioned problems is described and proven. This system is capable of simultaneously maximizing the power generated by every PV cell in the PV panel. The proposed configuration consists of an array of parallel-connected PV cells, a low-input-voltage step-up power converter, and a simple wide bandwidth MPP tracker. Parallel-configured PV systems are compared to traditional series-configured PV systems through both hardware experiments and computer simulations in this paper. Study results demonstrate that, under complex irradiance conditions, the power generated by the new configuration is approximately twice that of the traditional configuration. The solar PV system can be widely used in many consumer applications, such as PV vests for cell phones and music players.

A Technique for Improving P&O MPPT Performances of Double-Stage Grid-Connected Photovoltaic Systems

Abstract: In double-stage grid-connected photovoltaic (PV) inverters, the dynamic interactions among the DC/DC and DC/AC stages and the maximum power point tracking (MPPT) controller may reduce the system performances. In this paper, the detrimental effects, particularly in terms of system efficiency and MPPT performances, of the oscillations of the PV array voltage, taking place at the second harmonic of the grid frequency are evidenced. The use of a proper compensation network acting on the error signal between a reference signal provided by the MPPT controller and a signal that is proportional to the PV array voltage is proposed. The guidelines for the proper joint design of the compensation network (which is able to cancel out the PV voltage oscillations) and of the main MPPT parameters are provided in this paper. Simulation results and experimental measurements confirm the effectiveness of the proposed approach.

Artificial neural network-polar coordinated fuzzy controller based maximum power point tracking control under partially shaded conditions

Abstract: The one of main causes of reducing energy yield of photovoltaic systems is partially shaded conditions. Although the conventional maximum power point tracking (MPPT) control algorithms operate well under uniform insolation, they do not operate well in non-uniform insolation. The non-uniform conditions cause multiple local maximum power points on the power-voltage curve. The conventional MPPT methods cannot distinguish between the global and local peaks. Since the global maximum power point (MPP) may change within a large voltage window and also its position depends on shading patterns, it is very difficult to recognise the global operating point under partially shaded conditions. In this paper, a novel MPPT system is proposed for partially shaded PV array using artificial neural network (ANN) and fuzzy logic with polar information controller. The ANN with three layer feed-forward is trained once for several partially shaded conditions to determine the global MPP voltage. The fuzzy logic with polar information controller uses the global MPP voltage as a reference voltage to generate the required control signal for the power converter. Another objective of this study is to determine the estimated maximum power and energy generation of PV system through the same ANN structure. The effectiveness of the proposed method is demonstrated under the experimental real-time simulation technique based dSPACE real-time interface system for different interconnected PV arrays such as series-parallel, bridge link and total cross tied configurations.

A Control Methodology and Characterization of Dynamics for a Photovoltaic (PV) System Interfaced With a Distribution Network

Abstract: This paper proposes a control strategy for a single-stage, three-phase, photovoltaic (PV) system that is connected to a distribution network. The control is based on an inner current-control loop and an outer DC-link voltage regulator. The current-control mechanism decouples the PV system dynamics from those of the network and the loads. The DC-link voltage-control scheme enables control and maximization of the real power output. Proper feedforward actions are proposed for the current-control loop to make its dynamics independent of those of the rest of the system. Further, a feedforward compensation mechanism is proposed for the DC-link voltage-control loop, to make the PV system dynamics immune to the PV array nonlinear characteristic. This, in turn, permits the design and optimization of the PV system controllers for a wide range of operating conditions. A modal/sensitivity analysis is also conducted on a linearized model of the overall system, to characterize dynamic properties of the system, to evaluate robustness of the controllers, and to identify the nature of interactions between the PV system and the network/loads. The results of the modal analysis confirm that under the proposed control strategy, dynamics of the PV system are decoupled from those of the distribution network and, therefore, the PV system does not destabilize the distribution network. It is also shown that the PV system dynamics are not influenced by those of the network (i.e., the PV system maintains its stability and dynamic properties despite major variations in the line length, line X/R ratio, load type, and load distance from the PV system).

Modeling and Control of PV Charger System With SEPIC Converter

Abstract: The photovoltaic (PV) stand-alone system requires a battery charger for energy storage. This paper presents the modeling and controller design of the PV charger system implemented with the single-ended primary inductance converter (SEPIC). The designed SEPIC employs the peak-current-mode control with the current command generated from the input PV voltage regulating loop, where the voltage command is determined by both the PV module maximum power point tracking (MPPT) control loop and the battery charging loop. The control objective is to balance the power flow from the PV module to the battery and the load such that the PV power is utilized effectively and the battery is charged with three charging stages. This paper gives a detailed modeling of the SEPIC with the PV module input and peak-current-mode control first. Accordingly, the PV voltage controller, as well as the adaptive MPPT controller, is designed. An 80-W prototype system is built. The effectiveness of the proposed methods is proved with some simulation and experimental results.

Voltage Support Provided by a Droop-Controlled Multifunctional Inverter

Abstract: This paper presents a single-phase multifunctional inverter for photovoltaic (PV) systems application. The converter provides active power to local loads and injects reactive power into the grid providing voltage support at fundamental frequency. The proposed topology is controlled by means of the droop-control technique. Hence, it allows the obtaining of voltage-sag-compensation capability, endowing voltage ride-through to the system. A model and analysis of the whole system is given to properly choose the control parameters. Simulation and experimental results validate the proposed control using a 5-kVA PV converter.

Improved Energy Capture in Series String Photovoltaics via Smart Distributed Power Electronics

Abstract: This paper proposes an improved module integrated converter to increase energy capture in the photovoltaic (PV) series string. Prototypes for self-powered, high efficiency dc-dc converters that operate with autonomous control for tracking the maximum power of solar panels locally and on a fine scale are simulated, built and tested. The resulting module is a low-cost, reliable smart PV panel that operates independently of the geometry and complexity of the surrounding system. The controller maximizes energy capture by selection of one of three possible modes: buck, boost and pass-through. Autonomous controllers achieve noninteracting maximum power point tracking and a constant string voltage. The proposed module-integrated converters are verified in simulation. Experimental results show that the converter prototype achieves efficiencies of over 95% for most of its operating range. A 3-module PV series string was tested under mismatched solar irradiation conditions and increases of up to 38% power capture were measured.

Design of a Solar-Harvesting Circuit for Batteryless Embedded Systems

Abstract: The limited battery lifetime of modern embedded systems and mobile devices necessitates frequent battery recharging or replacement. Solar energy and small-size photovoltaic (PV) systems are attractive solutions to increase the autonomy of embedded and personal devices attempting to achieve perpetual operation. We present a battery less solar-harvesting circuit that is tailored to the needs of low-power applications. The harvester performs maximum-power-point tracking of solar energy collection under nonstationary light conditions, with high efficiency and low energy cost exploiting miniaturized PV modules. We characterize the performance of the circuit by means of simulation and extensive testing under various charging and discharging conditions. Much attention has been given to identify the power losses of the different circuit components. Results show that our system can achieve low power consumption with increased efficiency and cheap implementation. We discuss how the scavenger improves upon state-of-the-art technology with a measured power consumption of less than 1 mW. We obtain increments of global efficiency up to 80%, diverging from ideality by less than 10%. Moreover, we analyze the behavior of super capacitors. We find that the voltage across the supercapacitor may be an unreliable indicator for the stored energy under some circumstances, and this should be taken into account when energy management policies are used.

Development of a MATLAB/Simulink Model of a Single-Phase Grid-Connected Photovoltaic System

Abstract: Because of their deployment in dispersed locations on the lowest voltage portions of the grid, photovoltaic (PV) systems pose unique challenges to power system engineers. Computer models that accurately simulate the relevant behavior of PV systems would thus be of high value. However, most of today's models either do not accurately model the dynamics of the maximum power point trackers (MPPTs) or anti-islanding algorithms, or they involve excessive computational overhead for this application. To address this need, a Matlab/Simulink model of a single-phase grid-connected PV inverter has been developed and experimentally tested. The development of the PV array model, the integration of the MPPT with an averaged model of the power electronics, and the Simulink implementation are described. It is experimentally demonstrated that the model works well in predicting the general behaviors of single-phase grid-connected PV systems. This paper concludes with a discussion of the need for a full gradient-based MPPT model, as opposed to a commonly used simplified MPPT model.

Sensitivity Study of the Dynamics of Three-Phase Photovoltaic Inverters With an LCL Grid Filter

Abstract: An accurate small-signal model of three-phase photovoltaic (PV) inverters with a high-order grid filter is derived in this paper. The proposed model takes into account the influence of both the inverter operating point and the PV panel characteristics on the inverter dynamic response. A sensitivity study of the control loops to variations of the DC voltage, PV panel transconductance, supplied power, and grid inductance is performed using the proposed small-signal model. Analytical and experimental results carried out on a 100-kW PV inverter are presented.

Modeling of a variable speed wind turbine with a Permanent Magnet Synchronous Generator

Abstract: The aim of this work is to analyze a typical configuration of a Wind Turbine Generator System (WTGS) equipped with a Variable Speed Generator. Nowadays, doubly-fed induction generators are being widely used on WTGS, although synchronous generators are being extensively utilized too. There are different types of synchronous generators, but the multi-pole Permanent Magnet Synchronous Generator (PMSG) is chosen in order to obtain its model. It offers better performance due to higher efficiency and less maintenance since it does not have rotor current and can be used without a gearbox, which also implies a reduction of the weight of the nacelle and a reduction of costs. Apart from the generator, the analyzed WTGS consists of another three parts: wind speed, wind turbine and drive train. These elements have been modeled and the equations that explain their behavior have been introduced. What is more, the whole WTGS has been implemented in MATLAB/Simulink interface. Moreover, the concept of the Maximum Power Point Tracking (MPPT) has been presented in terms of the adjustment of the generator rotor speed according to instantaneous wind speed.

A Single-Phase Voltage-Controlled Grid-Connected Photovoltaic System With Power Quality Conditioner Functionality

Abstract: Future ancillary services provided by photovoltaic (PV) systems could facilitate their penetration in power systems. In addition, low-power PV systems can be designed to improve the power quality. This paper presents a single-phase PV system that provides grid voltage support and compensation of harmonic distortion at the point of common coupling thanks to a repetitive controller. The power provided by the PV panels is controlled by a Maximum Power Point Tracking algorithm based on the incremental conductance method specifically modified to control the phase of the PV inverter voltage. Simulation and experimental results validate the presented solution.

Maximum Power Tracking Control for a Wind Turbine System Including a Matrix Converter

Abstract: This paper focuses on maximum wind power extraction for a wind energy conversion system composed of a wind turbine, a squirrel-cage induction generator, and a matrix converter (MC). At a given wind velocity, the mechanical power available from a wind turbine is a function of its shaft speed. In order to track maximum power, the MC adjusts the induction generator terminal frequency, and thus, the turbine shaft speed. The MC also adjusts the reactive power transfer at the grid interface toward voltage regulation or power factor correction. A maximum power point tracking (MPPT) algorithm is included in the control system. Conclusions about the effectiveness of the proposed scheme are supported by analysis and simulation results.

Low-Complexity MPPT Technique Exploiting the PV Module MPP Locus Characterization

Abstract: This paper proposes a method for tracking the maximum power point (MPP) of a photovoltaic (PV) module that exploits the relation existing between the values of module voltage and current at the MPP (MPP locus). Experimental evidence shows that this relation tends to be linear in conditions of high solar irradiation. The analysis of the PV module electrical model allows one to justify this result and to derive a linear approximation of the MPP locus. Based on that, an MPP tracking strategy is devised which presents high effectiveness, low complexity, and the inherent possibility to compensate for temperature variations by periodically sensing the module open circuit voltage. The proposed method is particularly suitable for low-cost PV systems and has been successfully tested in a solar-powered 55-W battery charger circuit.

Sensorless Maximum Power Point Tracking of Wind by DFIG Using Rotor Position Phase Lock Loop (PLL)

Abstract: This paper presents an invention, the rotor position phase lock loop (PLL), which enables maximum power point (MPPT) tracking of wind by doubly-fed induction generators without needing a tachometer, an absolute position encoder, or an anemometer. The rotor position PLL is parameter variation insensitive, requiring only an estimate of the magnetization inductance for it to operate. It is also insensitive to noise in the electrical measurements. Proof of concept is by: (1) digital simulations and (2) experimental testing of a laboratory prototype.

A Single-Stage Single-Phase Transformer-Less Doubly Grounded Grid-Connected PV Interface

Abstract: A transformer provides galvanic isolation and grounding of the photovoltaic (PV) array in a PV-fed grid-connected inverter. Inclusion of the transformer, however, may increase the cost and/or bulk of the system. To overcome this drawback, a single-phase, single-stage [no extra converter for voltage boost or maximum power point tracking (MPPT)], doubly grounded, transformer-less PV interface, based on the buck-boost principle, is presented. The configuration is compact and uses lesser components. Only one (undivided) PV source and one buck-boost inductor are used and shared between the two half cycles, which prevents asymmetrical operation and parameter mismatch problems. Total harmonic distortion and DC component of the current supplied to the grid is low, compared to existing topologies and conform to standards like IEEE 1547. A brief review of the existing, transformer-less, grid-connected inverter topologies is also included. It is demonstrated that, as compared to the split PV source topology, the proposed configuration is more effective in MPPT and array utilization. Design and analysis of the inverter in discontinuous conduction mode is carried out. Simulation and experimental results are presented.

Energy Comparison of Seven MPPT Techniques for PV Systems

Abstract: In the future, solar energy will be a very important energy source. Several studies suppose that more than 45% of the energy in the world will be generated by photovoltaic array. Therefore it is necessary to concentrate our forces to reduce the application costs and to increment their performance. In order to reach the last aspect, it is important to note that the output characteristic of a photovoltaic array is nonlinear and changes with solar irradiation and cell’s temperature. Therefore a Maximum Power Point Tracking (MPPT) technique is needed to maximize the produced energy. This paper presents a comparative study of seven widely-adopted MPPT algorithms; their performance is evaluated using, for all the techniques, a common device with minimum hardware variations. In particular, this study compares the behaviors of each technique in presence of solar irradiation variations.

Experimental Performance of MPPT Algorithm for Photovoltaic Sources Subject to Inhomogeneous Insolation

Abstract: Photovoltaic (PV) power system performance depends on local irradiance conditions. PV systems are sometimes subject to partial shading, which may produce a nonideal characteristic curve, presenting true and local power maxima in the P -I curve. Traditional maximum power point tracking (MPPT) algorithms can converge to local maximum, which is not the true MPP. In order to solve the problem, this paper investigates the effects of nonuniform solar irradiance distribution on a PV source. An MPPT algorithm that is able to optimize the source instantaneous operating power under nonuniform irradiance is proposed. The ability of the algorithm and its increased performance with respect to traditional algorithms are evaluated by means of experimental tests performed on a real PV power system.

A New Variable-Speed Wind Energy Conversion System Using Permanent-Magnet Synchronous Generator and $Z$ -Source Inverter

Abstract: With the growth of wind energy conversion systems (WECSs), various technologies are developed for them. Permanent-magnet synchronous generators (PMSGs) are used by these technologies due to special characteristics of PMSGs such as low weight and volume, high performance, and the elimination of the gearbox. In this paper, a new variable-speed WECS with a PMSG and Z-source inverter is proposed. Characteristics of Z-source inverter are used for maximum power tracking control and delivering power to the grid, simultaneously. Two control methods are proposed for delivering power to the grid: Capacitor voltage control and dc-link voltage control. Operation of system with these methods is compared from the viewpoint of power quality and total switching device power (TSDP). In addition, TSDP, current ripple of inductor, performance, and total harmonic distortion of grid current of proposed system is compared with traditional wind energy system with a boost converter.

Fundamental-Frequency-Modulated Six-Level Diode-Clamped Multilevel Inverter for Three-Phase Stand-Alone Photovoltaic System

Abstract: This paper presents a fundamental-frequency-modulated diode-clamped multilevel inverter (DCMLI) scheme for a three-phase stand-alone photovoltaic (PV) system. The system consists of five series-connected PV modules, a six-level DCMLI generating fundamental-modulation staircase three-phase output voltages, and a three-phase induction motor as the load. In order to validate the proposed concept, simulation studies and experimental measurements using a small-scale laboratory prototype are also presented. The results show the feasibility of the fundamental frequency switching application in three-phase stand-alone PV power systems.