Topic
Microalloyed steel
About: Microalloyed steel is a research topic. Over the lifetime, 2183 publications have been published within this topic receiving 33586 citations.
Papers published on a yearly basis
Papers
More filters
TL;DR: In this article, the precipitation in four different dual-phase steels microalloyed with titanium was studied using transmission electron microscopy and it was shown that TiC particles (approximately 10nm) were the most dominant factor in strengthening.
57 citations
TL;DR: In this paper, cuboidally shaped inclusions were found to be responsible for cleavage initiation in a low-carbon, microalloyed steel, and electron microdiffraction was used to identify these inclusions as the fcc phase (NaCl prototype) in the titanium-nitrogen system.
Abstract: In Part I of this study, cuboidally shaped inclusions were found to be responsible for cleavage initiation in a low-carbon, microalloyed steel. In Part II, electron microdiffraction was used to identify these inclusions as the fcc phase (NaCl prototype) in the titanium-nitrogen system. A model for cleavage as induced by these inclusions is proposed. A microcrack begins on one side of the TiN inclusion, propagates to the other side, and then transfers into the matrix. Initiation at a particular location in the particle is believed to be caused by dislocation pileup impingement and stress concentrations such as crystal defects and surface irregularities within the TiN. Dislocations in the TiN inclusions were imaged by transmission electron microscopy (TEM). After the TiN microcrack transfers into the matrix, propagation spreads radially. From the area of crack transfer, two simultaneous propagation paths reverse directions and rotate around the particle. The particle separates these cracks for a short distance, they travel on different cleavage planes, and upon rejoining, a ridge of torn matrix is created. The location of this ridge can be used to infer where cleavage began in the TiN and where the microcrack transferred into the matrix. Tessellated residual stresses arising from differential thermal contraction between the TiN and the matrix are suggested to increase the cleavage-initiating potency of TiN inclusions.
57 citations
TL;DR: In this article, the authors investigated variant selection during the α-γ-α phase transformation in recrystallized, low-carbon, microalloyed steel and found that preferred nucleation at a grain boundary near a triple junction requires an orientation relationship close to the Kurdjumov-Sachs correspondence to both adjacent α grains.
57 citations
15 Jul 2008-Materials Science and Engineering A-structural Materials Properties Microstructure and Processing
TL;DR: In this paper, the authors evaluated the variations in the as-cast mechanical properties of low-carbon steels with and without vanadium and niobium and showed that good combinations of strength and ductility can be achieved by microalloying additions.
Abstract: Tensile and room temperature Charpy V-notch impact tests along with microstructural studies were used to evaluate the variations in the as-cast mechanical properties of low-carbon steels with and without vanadium and niobium. Tensile test results indicate that good combinations of strength and ductility can be achieved by microalloying additions. While the yield strength and UTS increase up to respectively 370–380 and 540–580 MPa in the microalloyed heats, their total elongation range from 20 to 25%. TEM studies revealed that random and interphase fine-scale microalloy precipitates play a major role in the strengthening of the microalloyed heats. On the other hand, microalloying additions significantly decreased the impact energy and led to the dominance of cleavage facets on the fracture surfaces. It seems that heterogeneous nucleation of microalloy carbonitrides on dislocations along with coarse ferrite grains and pearlite colonies trigger the brittle fracture in the microalloyed heats.
56 citations
TL;DR: In this article, the kinetics of metadynamic recrystallization (MDRX) were studied in a Mo, a Nb, and a Ti microalloyed steel at temperatures ranging from 850 °C to 1000 °C and strain rates from 0.02 to 2 s1.
Abstract: By means of interrupted torsion tests, the kinetics of metadynamic recrystallization (MDRX) were studied in a Mo, a Nb, and a Ti microalloyed steel at temperatures ranging from 850 °C to 1000 °C and strain rates from 0.02 to 2 s1. Quenches were also performed after full MDRX. In contrast to the case of static recrystallization (SRX), the kinetics of MDRX are shown to be highly sensitive to a change of an order of magnitude in strain rate and are relatively insensitive to temperature changes within the range of values applicable to industrial hot-rolling practice. A similar algebraic dependence of the MDRX grain size on strain rate and temperature was found in the three steels. The kinetics of MDRX were slower in the Nb than in the Mo steel, and those of the Ti steel were slower than in the Nb and Mo steels. Above 900 °C and 950 °C, the retardation of MDRX in the Nb and Ti steels, respectively, is due to solute drag. Models predicting the start time for Nb and Ti carbonitride precipitation showed that MDRX is delayed below these temperatures by this mechanism. Comparison of the MDRX and precipitation start times in the Nb steel indicated that a temperature of “no-MDRX” could not be defined, in contrast to the well-definedT
nr (no recrystallization temperature) of SRX. By means of torsion simulations composed of multiple interruptions, it is shown that MDRX is retarded decreasingly as the accumulated strain is increased. This appears to be due to the promotion of precipitate coarsening by the continuing deformation.
56 citations