Showing papers on "Microstrip antenna published in 2008"

A Compact Ultrawideband Antenna With 3.4/5.5 GHz Dual Band-Notched Characteristics

Abstract: We propose a compact planar ultrawideband (UWB) antenna with 3.4/5.5 GHz dual band-notched characteristics. The antenna consists of a beveled rectangular metal patch and a 50 Omega coplanar waveguide (CPW) transmission line. By etching two nested C-shaped slots in the patch, band-rejected filtering properties in the WiMAX/WLAN bands are achieved. The proposed antenna is successfully simulated, designed, and measured showing broadband matched impedance, stable radiation patterns and constant gain. An equivalent circuit model of the proposed antenna is presented to discuss the mechanism of the dual band-notched UWB antenna. A UWB antenna and a single band-notched one are also provided for references.

Isolation Enhancement Between Two Closely Packed Antennas

Abstract: This paper introduces a coupling element to enhance the isolation between two closely packed antennas operating at the same frequency band. The proposed structure consists of two antenna elements and a coupling element which is located in between the two antenna elements. The idea is to use field cancellation to enhance isolation by putting a coupling element which artificially creates an additional coupling path between the antenna elements. To validate the idea, a design for a USB dongle MIMO antenna for the 2.4 GHz WLAN band is presented. In this design, the antenna elements are etched on a compact low-cost FR4 PCB board with dimensions of 20times40times1.6 mm3. According to our measurement results, we can achieve more than 30 dB isolation between the antenna elements even though the two parallel individual planar inverted F antenna (PIFA) in the design share a solid ground plane with inter-antenna spacing (Center to Center) of less than 0.095 lambdao or edge to edge separations of just 3.6 mm (0.0294 lambdao). Both simulation and measurement results are used to confirm the antenna isolation and performance. The method can also be applied to different types of antennas such as non-planar antennas. Parametric studies and current distribution for the design are also included to show how to tune the structure and control the isolation.

Planar Slot Antenna Backed by Substrate Integrated Waveguide Cavity

Abstract: A novel design method of low profile cavity backed planar slot antenna has been described in this paper. The whole antenna including backed cavity and feeding element is completely constructed at a single substrate by using substrate integrated waveguide technique and grounded coplanar waveguide. An example with 1.7% bandwidth has been presented, which has 5.4 dBi gain, 16.1 dB front-to-back ratio and -19 dB maximum cross polarized radiation level with its total thickness less than lambda0/50. The proposed antenna keeps good radiation performance of conventional cavity backed antenna and has advantages of conventional planar antenna including low profile, light weight, easy fabrication with low cost and convenient integration with planar circuit.

Planar Ultrawideband Antennas With Multiple Notched Bands Based on Etched Slots on the Patch and/or Split Ring Resonators on the Feed Line

Abstract: Three types of ultrawideband (UWB) antennas with triple notched bands are proposed and investigated for UWB communication applications. The proposed antennas consist of a planar circular patch monopole UWB antenna and multiple etched slots on the patch and/or split ring resonators (SRRs) coupled to the feed line. Good agreement is achieved between the simulated and measured results. These techniques are significant for designing UWB antennas with multiple narrow frequency notched bands or for designing multiband antennas.

Mutual Coupling Reduction in Patch Antenna Arrays by Using a Planar EBG Structure and a Multilayer Dielectric Substrate

Abstract: Periodic structures can help in the reduction of mutual coupling by using their capability of suppressing surface waves propagation in a given frequency range. The purpose of this work is to show the viability of using a planar electromagnetic band gap (EBG) structure based on a truncated frequency selective surface (FSS) grounded slab to this aim. The goal is to use it in patch antenna arrays, keeping both the element separation smaller than for grating lobes avoidance (assuming broadside case) and the patch antenna size large enough to have a good antenna directivity. To this aim, a multilayer dielectric substrate composed of high and low permittivity layers is convenient. This allows the use of a planar EBG structure made of small elements printed on the high permittivity material and, at the same time, the low permittivity layer helps the bandwidth and the directivity of the antenna to be increased. The EBG structure was designed under these premises and optimized for the particular application via an external optimization algorithm based on evolutionary computation: ant colony optimization (ACO). The mutual coupling reduction has been measured and it is larger than 10 dB with a completely planar structure.

Design and Evaluation of a Reconfigurable Antenna Array for MIMO Systems

Abstract: New reconfigurable antenna array is demonstrated for multiple input multiple output (MIMO) communication systems that improves link capacity in closely spaced antenna arrays. The antenna system consists of an array of two printed dipoles separated by a distance of a quarter wavelength. Each of the dipoles can be reconfigured in length using PIN diode switches. The switch configuration can be modified in a manner adaptive to changes in the environment. The configuration of switches effects the mutual coupling between the array elements, and subsequently, the radiation pattern of each antenna, leading to different degrees of pattern diversity which can be used to improve link capacity. The PIN diode-based reconfigurable antenna solution is first motivated through a capacity analysis of the antenna in a clustered MIMO channel model. A new definition of spatial correlation coefficient is introduced to include the effects of antenna mismatch and radiation efficiency when quantifying the benefit of pattern diversity. Next, the widespread applicability of the proposed technique is demonstrated, relative to conventional half wavelength printed dipoles, using computational electromagnetic simulation in an outdoor and indoor environment and field measurements in an indoor laboratory environment. It is shown for the 2 times 2 system considered in this paper, that an average improvement of 10% and 8% is achieved in link capacity for a signal to noise ratio (SNR) respectively of 10 dB and 20 dB in an indoor environment compared to a system employing non reconfigurable antenna arrays.

60-GHz Patch Antennas and Arrays on LTCC With Embedded-Cavity Substrates

Abstract: The design is presented of aperture-coupled microstrip line-fed patch antennas (ACMPAs) and 4times4 planar arrays on Ferro A6-S low-temperature cofired ceramic (LTCC) substrate operating in the 60-GHz frequency band. In addition to the traditional ACMPA design, air cavities processed inside the LTCC substrate are used to improve the bandwidth and gain of the antennas. The arrays are excited through the microstrip-line feed networks using quarter-wave matched T-junctions and using Wilkinson power dividers. The results show that ACMPAs and arrays can be fabricated with a standard LTCC process even for the millimeter-wave region. Good agreement is achieved between simulations and measurements. The measured S-parameters indicate impedance bandwidths of 9.5% and 5.8% for the array elements with and without an embedded cavity. The measured maximum gains for the 16-element patch arrays (with and without cavity) are 18.2 and 15.7 dBi, respectively.

High Frequency Properties of Electro-Textiles for Wearable Antenna Applications

Abstract: A systematic study of the high frequency electrical properties of electro-textiles is presented in this paper. First, conductive thread characterization is completed with a waveguide cavity method. The effect of conductive thread density and comparison of several different types of conductive threads are included. Second, comparisons of knitted patterns and weave patterns are made in terms of effective electrical conductivity through a microstrip resonator method. The effect of various weave patterns on conductive and dielectric loss is detailed. Finally, the relevance of the high frequency characterization of the electro-textile materials is shown through electro-textile patch antenna fabrication and measurements. The efficiency of the fully fabric patch antenna is as high as 78% due to the use of low loss electrotextiles characterized in this paper.

Design of Miniaturized Metamaterial Patch Antennas With $\mu$ -Negative Loading

Abstract: Recent theoretical studies have shown that circular patch antennas loaded by an inhomogeneous substrate partially filled with a mu-negative (MNG) metamaterial may in principle support a resonant radiating mode, even if the total size of the radiator is significantly smaller than the wavelength of operation. In those theoretical analyses, MNG metamaterials have been assumed as continuous, isotropic and readily available materials, characterized by a proper dispersion in frequency and by inherent ohmic losses. The fabrication of such compact antennas, however, would require the major effort of designing proper subwavelength inclusions that realize the MNG behavior of the substrate, and consequently a careful design of their geometry, location and orientation. The fabrication of a fully isotropic MNG sample to reside underneath the sub-wavelength patch, moreover, may be challenging with the current technological limitations. In this paper, we first show that the proposed sub-wavelength radiator may operate even when the fabricated MNG sample is not isotropic, due to the specific polarization of the magnetic field in the MNG region. Then, we propose a complete design of the magnetic inclusions, presenting full-wave numerical simulations of the structure, which effectively supports the expected resonant mode, despite the small size of the antenna. The comparisons among analytical results of the patch loaded by: (a) the ideal MNG sample applying a simple cavity model; (b) full-wave numerical simulations of the same antenna considering the presence of the feed; and (c) full-wave numerical simulations of the antenna loaded by the proposed magnetic inclusions, show how our design effectively simulate the presence of an MNG sample, allowing the realistic design of a sub-wavelength metamaterial patch antenna with satisfactory matching and radiating features. This may open up new venues in the realization of efficient metamaterial radiating components for practical purposes.

A Novel Single-Feed Circular Microstrip Antenna With Reconfigurable Polarization Capability

Abstract: A single-feed circular microstrip antenna with reconfigurable polarization capability is proposed. This antenna has a simple structure, which consists of a radiating circular patch, five switches (PIN diode), three matching stubs, and a 50 microstrip feed line. It can be switched between 4 different states: two states (low-frequency and high-frequency) for linear polarization (LP), one state for left hand circular polarization (LHCP) and one for right hand circular polarization (RHCP) by controlling the bias voltage of two PIN diodes. At the same time, three switchable matching stubs are used for matching every polarization state. Simulation results and experimental results show that the proposed antenna demonstrates a low cross polarization level, good impedance bandwidth, and a very good axial ratio in the circularly polarized states.

Frequency Reconfigurable U-Slot Microstrip Patch Antenna

Abstract: A frequency reconfigurable microstrip patch antenna is presented. It is found that the incorporation of a U-slot in the patch can provide a flat input resistance and a linear input reactance across a wider bandwidth than the conventional patch antenna. By placing a variable capacitor and an inductor at the antenna input, the impedance matching frequency of the antenna can be varied. The fabricated prototype antenna attains a tunable frequency range from 2.6 to 3.35 GHz. The proposed antenna is simple in structure, and the control circuitry is placed underneath the ground plane. It is suitable for use in reducing the crosstalk from adjacent channels in multichannel system.

Design and Study of Wideband Single Feed Circularly Polarized Microstrip Antennas

Abstract: The performance of single feed truncated corner circularly polarized microstrip antennas with different substrate thickness is studied by simulation and experiment. It is found that the axial ratio bandwidth could be enhanced considerably when a thicker substrate is used, provided that a U-slot and/or L-probe is used to effect impedance matching. One of the configurations attains an axial ratio bandwidth (< 3 dB) of about 14% within the impedance matching band when the substrate thickness is about 0.2λo.

A Low-Cost 60-GHz Switched-Beam Patch Antenna Array With Butler Matrix Network

Abstract: In this letter, a low-cost 60-GHz switched-beam patch antenna array with Butler matrix network is developed and experimentally demonstrated. In order to improve integration with the patch elements, a 4 times 4 planar Butler matrix is implemented in a low-dielectric substrate. The four rectangular patches fed by inset microstrip lines are connected to the outputs of the Butler matrix for the 60-GHz operation. Because of the fabrication tolerances, the operating frequency of the fabricated antenna shifts to 62 GHz. The radiation patterns measured at 62 GHz are in good agreement with the theoretical array factors. The antenna developed in this letter provides a cost-effective approach to implement an adaptive antenna for 60-GHz wireless communications.

Dual- and Multiband U-Slot Patch Antennas

Abstract: A wide band patch antenna fed by an L-probe can be designed for dual- and multi-band application by cutting U-slots on the patch. Simulation and measurement results are presented to illustrate this design.

Half-Mode Substrate Integrated Waveguide (HMSIW) Leaky-Wave Antenna for Millimeter-Wave Applications

Abstract: A novel leaky-wave antenna is demonstrated and developed at Ka-band in this work based on the newly proposed half-mode substrate integrated waveguide (HWSIW). This antenna is accurately simulated by using a full-wave electromagnetic simulator and then fabricated through a single-layer printed circuit board (PCB) process. Wide bandwidth and a quasi-omnidirectional radiation pattern are obtained. The proposed antenna is therefore a good candidate for millimeter-wave applications. Measured results are in good agreement with simulated results.

A Small Antipodal Vivaldi Antenna for Ultrawide-Band Applications

Abstract: A compact antipodal Vivaldi antenna for ultrawide-band (UWB) applications is proposed. The antenna operates across the entire UWB spectrum from 3.1 to 10.6 GHz, and also has low cross-polarization levels and reasonable gain values over the same frequency band. Two different substrates, Rogers RO3006 and FR4, are considered, and results regarding return loss, far field pattern, phase response, group delay, and gain are presented.

A 60-GHz Millimeter-Wave CPW-Fed Yagi Antenna Fabricated by Using 0.18- $\mu\hbox{m}$ CMOS Technology

Abstract: This letter presents a 60-GHz millimeter-wave on-chip Yagi antenna fabricated with a 0.18-mum CMOS process. A feeding network is designed in a coplanar waveguide (CPW) technology. The 0.18-mum six-metal-layer CMOS process allows the on-chip antenna to utilize a simple CPW-to-coplanar-stripline feed transition and the first metal layer to implement a reflector strip. The CMOS antenna chip size is 1.1 x 0.95 mm2 . A FEM-based 3D full-wave electromagnetic solver, the HFSS, is used for design simulation. The measured antenna input VSWR is less than two from 55 to 65 GHz. The front-to-back ratio of the Yagi antenna is about 9 dB. The measured maximum antenna power gain is about -10 dBi. The simulated antenna radiation efficiency is about 10%.

A novel uwb elliptical slot antenna with band-notched characteristics

Abstract: This paper presents a novel band-notched elliptical slot antenna for Ultra Wide-Band (UWB) communication, which is printed on a dielectric substrate of RT/duroid 6006 with relative permittivity (er) of 6.0, thickness of 1.27 mm, and fed by an elliptical open ended microstrip line connected to the 50 Ω main line. This antenna is designed to be used in frequency band of 3.1–10.6 GHz. Bandnotched characteristics of antenna to reject the frequency band of 5.15–5.825GHz, which is limited by IEEE 802.11a, is realized by parasitic inverted-U strip attached to the elliptical slot plane. Effects of varying the parameters of parasitic inverted-U strip on performance of proposed antenna have been investigated. The antenna with optimal parameters obtained from parametric study is fabricated and measured. It is observed that the simulation and experimental results have good agreements with each other. 128 Fallahi, Kalteh, and Golparvar Roozbahani

Full-Wave Modal Dispersion Analysis and Broadside Optimization for a Class of Microstrip CRLH Leaky-Wave Antennas

Abstract: In this paper, a planar microstrip composite right/left-handed leaky-wave antenna is analyzed and designed as an infinite 1-D periodic microstrip leaky-wave antenna. A parametric study, based on a full-wave numerical modal approach that analyzes a unit cell using a periodic layered-medium Green's function, is shown to be an efficient approach to accurately design the structure, completely eliminating open-stopband effects and achieving an almost constant radiation efficiency when the beam is scanned through broadside. Results obtained by the proposed approach are compared with those obtained by means of both an artificial transmission-line analysis and a Bloch-wave analysis, which use the full-wave simulation of a finite-length structure. The balanced condition is interpreted in terms of the behavior of the phase and attenuation constants relevant to the radiating harmonic. Furthermore, it is shown how radiation at broadside is guaranteed by the presence of two radiating elements (one series and one shunt) within the equivalent circuit of the unit cell. The effectiveness of the analysis is demonstrated through the design of a finite-length antenna excited by a source at one end.

A Widely Tunable Compact Patch Antenna

Abstract: In this letter, we propose a tunable patch antenna made of a slotted rectangular patch loaded by a number of posts close to the patch edge. The posts are short circuited to the ground plane via a set of PIN diode switches. Simulations and measurements verify the possibility of tuning the antenna in subbands from 620 to 1150 MHz. Good matching has been achieved over most of the bands. Other performed designs show that more than one octave can be achieved using the proposed structure.

Printed Omni-Directional UWB Monopole Antenna With Very Compact Size

Abstract: A compact rectangular monopole with an equal-width ground plane is presented This novel structural configuration could significantly improve its radiation performance and decrease its size The feeding structure composed of a trident-shaped strip and a tapered impedance transformer is presented and discussed Its impedance bandwidth, defined by measured VSWR less than 2, is from 275 to 162 GHz with a ratio of about 59:1 Both numerical and experimental results show that the proposed monopole antenna has stably omni-directional H-plane radiation patterns with low cross-polarization level within its impedance bandwidth This novel monopole antenna has ultrawide impedance bandwidth, very compact size (30 mm*8 mm), low fabrication lost, and omni-directional H-plane radiation patterns, which are suitable for various broadband applications

Phase reciprocity of spin-wave excitation by a microstrip antenna

Abstract: Using space-, time-, and phase-resolved Brillouin light-scattering spectroscopy we investigate the difference in phase of the two counterpropagating spin waves excited by the same microwave microstrip transducer. These studies are performed both for backward volume magnetostatic waves and magnetostatic surface waves in an in-plane magnetized yttrium iron garnet film. The experiments show that for the backward volume magnetostatic spin waves which are reciprocal and excited symmetrically in amplitude there is a phase difference of associated with the excitation process and thus the phase symmetry is distorted. On the contrary, for the magnetostatic surface spin waves which are nonreciprocal and unsymmetrical in amplitude the phase symmetry is preserved there is no phase difference between the two waves associated with the excitation. Theoretical analysis confirms this effect.

Antenna for a level meter employing the radar principle

Abstract: In an antenna for a level meter employing the radar principle, a fastening device is provided for detachably mounting a dielectric insert in the antenna. The fastening device may be a continuous clamping collar that clamps the dielectric insert in place in the antenna. This offers a simple, universally employable possibility for fastening a dielectric insert in the antenna.

A High-Isolation, Wideband and Dual-Linear Polarization Patch Antenna

Abstract: The design of a dual-polarization stacked patch antenna to be used in GSM-UMTS base station arrays is presented. The patch shows a high matching level in a broadband and isolation between elements that make it a suitable radiating element for base station arrays. Moreover, the most relevant achievement of this element is the isolation between the two polarization ports of the same element in the antenna operating bandwidth. A prototype has been manufactured and measured. The measurements, that match the design objectives, are also presented.

A Single Layer Wideband U-Slot Microstrip Patch Antenna Array

Abstract: The design and measured results of a 2 times 2 microstrip line fed U-slot rectangular antenna array are presented. The U-slot patches and the feeding network are placed on the same layer, resulting in a very simple structure. The advantage of the microstrip line fed U-slot patch is that it is easy to form the array. An impedance bandwidth (VSWR < 2) of 18% ranging from 5.65 GHz to 6.78 GHz is achieved. The radiation performance including radiation pattern, cross polarization, and gain is also satisfactory within this bandwidth. The measured peak gain of the array is 11.5 dBi. The agreement between simulated results and the measurement ones is good. The 2 times 2 array may be used as a module to form larger array.

Single-Fed Microstrip Patch Antenna With Switchable Polarization

Abstract: A single-fed reconfigurable microstrip antenna that can provide various polarization diversities is presented in this paper. The antenna is excited by a microstrip feed line through aperture coupling. When two PIN diodes are used to respectively reconfigure the coupling slot and the open stub of the feed line, the polarization of the microstrip antenna can be switched between vertical and horizontal polarizations. For the reconfigurable antenna with the linear polarization diversity, it can be converted to a circularly-polarized antenna with switchable polarization sense by introducing a perturbation segment. Moreover, an antenna with the quadri-polarization diversity, including dual orthogonal linear polarizations and two circular polarizations, is also developed from the structure of the switchable circular polarization microstrip antenna, and only three diodes are required. Details of the antenna design are shown, and the measured results for the constructed prototype are also exhibited and discussed.

Compact Circularly Polarized Rectenna With Unbalanced Circular Slots

Abstract: A novel rectifying antenna (rectenna) using a compact circularly polarized (CP) patch antenna with RF-to-DC power conversion part at 2.45 GHz is introduced, in which the unbalanced slots structure is adopted for size reduction and 2nd harmonic rejection. To contribute a rectenna for RF power conversion, the back side of the CP antenna is the doubler rectifier circuit with 3rd order harmonic rejection radial stub for efficiency optimization and harmonic power re-radiation elimination. The adopted CP antenna built on low cost FR-4 substrate has measured bandwidth of 137 MHz (10 dB return loss) as well as 30 MHz CP bandwidth (3 dB axial ratio). By up to 3rd order harmonic rejection, the RF-to-DC conversion efficiency would reach 53% and 75% with 1 K Omega resistor load under ANSI/IEEE uncontrolled and controlled RF human exposure limit respectively.

CPW-Fed Multi-Band Omni-Directional Planar Microstrip Antenna Using Composite Metamaterial Resonators for Wireless Communications

Abstract: A novel approach for the design of a compact multiband planar microstrip antenna is presented. This type of antenna is composed of composite metamaterial resonators (including conditional microstrip resonators and metamaterial resonators), and fed by signal feed. A sample antenna with composite closed-ring resonator and split-ring resonator (SRR) fed by 50 Ω coplanar waveguide (CPW) developed on FR4 epoxy substrate for multi-band wireless communication applications is presented. Appropriate design of the composite structure resulted in three discontinuous resonant bands. The fundamental magnetic resonant and electric resonant frequency of SRR and the first electric resonant frequency of the closed-ring resonator were combined to form low, middle, and high resonant band. The properties of this antenna are investigated by theoretical analysis and finite element method (FEM) simulations. The numerical results show that the proposed antenna has good impedance bandwidth and radiation characteristics in the three operating bands which cover the required band widths of the 2.4/5.2/5.8GHz wireless local-area networks (WLAN) and 3.5/5.5 GHz worldwide interoperability for microwave access (WiMax) with return loss of better than 10 dB. The antenna also has stably omni-directional H-plane radiation patterns within the three operating bands.

A Folded-Monopole Model for Electrically Small NRI-TL Metamaterial Antennas

Abstract: An improved model for analyzing electrically small NRI-TL antennas is proposed, that highlights the methods that enable these antennas to offer a good impedance match and a high radiation efficiency compared to previously reported designs. An even-odd mode analysis reveals that the antenna supports a predominately even-mode current on the vertical vias, allowing the antenna to be modeled using a multiple folded monopole topology, which provides a substantial increase in the radiation resistance of the antenna. This, together with the top-loading effect of the microstrip line on the vias, enables the antenna to be matched to 50 Omega without the use of an external matching network, while maintaining a high radiation efficiency. The validity of the proposed model is confirmed with a fabricated prototype, that consists of four microstrip zero-degree NRI-TL unit cells with dimensions of lambda0/10 times lambda0/10 times lambda/20 over a 0.45lambda0 times 0.45lambda0 ground plane. The antenna's performance is verified by full-wave simulations and experimental data obtained at 3.1 GHz, which yield a vertical linear electric field polarization, a measured -10dB return-loss bandwidth of 53 MHz and a measured efficiency of 70%.

Novel Modified UWB Planar Monopole Antenna With Variable Frequency Band-Notch Function

Abstract: A novel modified microstrip-fed ultrawideband (UWB) planar monopole antenna with variable frequency band-notch characteristic is presented. By inserting two slots in the both sides of microstrip feedline on the ground plane, much wider impedance bandwidth can be produced. A modified H-shaped conductor-backed plane with variable dimensions is used in order to generate the frequency band-stop performance and control its characteristics such as band-notch frequency and its bandwidth. The designed antenna has a small size of 22 x 22 mm2 and operates over the frequency band between 3.1 and 14 GHz for VSWR < 2 while showing the band rejection performance in the frequency band of 5.1 to 5.9 GHz.