Showing papers on "Modulation published in 2011"
TL;DR: Graphene-based optical modulation mechanism, with combined advantages of compact footprint, low operation voltage and ultrafast modulation speed across a broad range of wavelengths, can enable novel architectures for on-chip optical communications.
Abstract: Graphene, the single-atom-thick form of carbon, holds promise for many applications, notably in electronics where it can complement or be integrated with silicon-based devices. Intense efforts have been devoted to develop a key enabling device, a broadband, fast optical modulator with a small device footprint. Now Liu et al. demonstrate an exciting new possibility for graphene in the area of on-chip optical communication: a graphene-based optical modulator integrated with a silicon chip. This new device relies on the electrical tuning of the Fermi level of the graphene sheet, and achieves modulation of guided light at frequencies over 1 gigahertz, together with a broad operating spectrum. At just 25 square micrometres in area, it is one of the smallest of its type. Integrated optical modulators with high modulation speed, small footprint and large optical bandwidth are poised to be the enabling devices for on-chip optical interconnects1,2. Semiconductor modulators have therefore been heavily researched over the past few years. However, the device footprint of silicon-based modulators is of the order of millimetres, owing to its weak electro-optical properties3. Germanium and compound semiconductors, on the other hand, face the major challenge of integration with existing silicon electronics and photonics platforms4,5,6. Integrating silicon modulators with high-quality-factor optical resonators increases the modulation strength, but these devices suffer from intrinsic narrow bandwidth and require sophisticated optical design; they also have stringent fabrication requirements and limited temperature tolerances7. Finding a complementary metal-oxide-semiconductor (CMOS)-compatible material with adequate modulation speed and strength has therefore become a task of not only scientific interest, but also industrial importance. Here we experimentally demonstrate a broadband, high-speed, waveguide-integrated electroabsorption modulator based on monolayer graphene. By electrically tuning the Fermi level of the graphene sheet, we demonstrate modulation of the guided light at frequencies over 1 GHz, together with a broad operation spectrum that ranges from 1.35 to 1.6 µm under ambient conditions. The high modulation efficiency of graphene results in an active device area of merely 25 µm2, which is among the smallest to date. This graphene-based optical modulation mechanism, with combined advantages of compact footprint, low operation voltage and ultrafast modulation speed across a broad range of wavelengths, can enable novel architectures for on-chip optical communications.
3,105 citations
TL;DR: Spatial Modulation is a novel and recently proposed multiple-antenna transmission technique that can offer, with a very low system complexity, improved data rates compared to Single-Input- Single-Output (SISO) systems, and robust error performance even in correlated channel environments.
Abstract: Multiple-antenna techniques constitute a key technology for modern wireless communications, which trade-off superior error performance and higher data rates for increased system complexity and cost. Among the many transmission principles that exploit multiple-antenna at either the transmitter, the receiver, or both, Spatial Modulation (SM) is a novel and recently proposed multiple-antenna transmission technique that can offer, with a very low system complexity, improved data rates compared to Single-Input- Single-Output (SISO) systems, and robust error performance even in correlated channel environments. SM is an entirely new modulation concept that exploits the uniqueness and randomness properties of the wireless channel for communication. This is achieved by adopting a simple but effective coding mechanism that establishes a one-to-one mapping between blocks of information bits to be transmitted and the spatial positions of the transmit-antenna in the antenna-array. In this article, we summarize the latest research achievements and outline some relevant open research issues of this recently proposed transmission technique.
720 citations
05 Jun 2011
TL;DR: Novel modulation techniques are proposed for coding and decoding information of the so-called messenger molecule concentration waves in nanonetworks that achieve high channel capacity values and exhibits more robustness against noise and requires less power.
Abstract: Communication via diffusion of molecules is an effective method for transporting information in nanonetworks. In this paper, novel modulation techniques called Concentration Shift Keying (CSK) and Molecule Shift Keying (MSK) are proposed for coding and decoding information of the so-called messenger molecule concentration waves in nanonetworks. The first technique, CSK, modulates the information via the variation in the concentration of the messenger molecules whereas MSK utilizes different types of messenger molecules to represent the information. Using simulation, the performance of these modulation techniques is evaluated in terms of susceptibility to noise and transmission power requirements. The new techniques achieve high channel capacity values, in particular, the MSK technique exhibits more robustness against noise and requires less power.
399 citations
Patent•
09 Nov 2011TL;DR: In this paper, the first analog radio frequency signal including a signal of interest and an interference signal caused by a second analog signal transmitted in full duplex over a channel from which the first analogue transmission is received is provided.
Abstract: In one aspect there is provided a method. The method may include receiving a first analog radio frequency signal including a signal of interest and an interference signal caused by a second analog radio frequency signal transmitted in full duplex over a channel from which the first analog transmission is received; combining the first analog radio frequency signal and a portion of the second analog radio frequency signal to generate an output analog radio frequency signal characterized by at least a reduction or an elimination of the interference signal included in the output analog radio frequency signal; and providing the output analog radio frequency signal. Related apparatus, systems, methods, and articles are also described.
344 citations
TL;DR: In this paper, the authors studied coherent electronic transport in charge-density-tunable microdevices patterned from thin films of the topological insulator (TI) Bi${}_{2}$Se${}_3}$.
Abstract: We study coherent electronic transport in charge-density-tunable microdevices patterned from thin films of the topological insulator (TI) Bi${}_{2}$Se${}_{3}$. The devices exhibit pronounced electric field effect, including ambipolar modulation of the resistance with an on-and-off ratio of 500%. We show that the weak antilocalization correction to conductance is sensitive to the number of coherently coupled channels, which in a TI includes the top and bottom surfaces and the bulk carriers. These are separated into coherently independent channels by the application of gate voltage and at elevated temperatures. Our results are consistent with a model where channel separation is determined by a competition between the phase coherence time and the surface-to-bulk scattering time.
300 citations
01 Dec 2011
TL;DR: A modified technique is proposed which avoids bit error propagation whilst retaining the benefits of the concept and can lead to a decrease of the peak system power, which is highly beneficial in the context of optical wireless communication.
Abstract: A novel modulation technique coined SIM-OFDM was recently proposed. SIM-OFDM uses different frequency carrier states to convey information and leads to increased performance in comparison to conventional OFDM. Additionally, its innovative structure can lead to a decrease of the peak system power, which is highly beneficial in the context of optical wireless communication. One of the issues of the original SIM-OFDM scheme is a potential bit error propagation which could lead to significant burst errors. The current paper proposes a modified technique which avoids bit error propagation whilst retaining the benefits of the concept.
241 citations
TL;DR: In this article, the performance of DC-biased and asymmetrically clipped optical OFDM (ACO-OFDM) is analyzed in the presence of light emitting diode (LED) nonlinear distortions.
Abstract: This paper analyzes the performance of indoor orthogonal frequency division multiplexing (OFDM) optical wireless communication systems in the presence of light emitting diode (LED) nonlinear distortions. There are several forms of optical OFDM using intensity modulation [7th Int. Symp. on Communication Systems Networks and Digital Signal Processing (CSNDSP), 2010, pp. 566-570]. In this paper, DC-biased optical OFDM (DCO-OFDM) and asymmetrically clipped optical OFDM (ACO-OFDM) are considered. ACO-OFDM produces a half-wave symmetry time signal at the output of the OFDM modulator by special assignment of subcarriers, thus allowing signal clipping at the zero level and avoiding the need for DC bias at the expense of data rate reduction. DCO-OFDM assigns data to all possible subcarriers to increase the data rate. However, half-wave symmetry signals cannot be achieved and a high DC bias is needed to convert the bipolar signal to a unipolar signal before modulating the LED intensity. This paper considers a practical LED model and studies the performance of both systems in terms of average electrical OFDM signal power versus bit error ratio in the presence of an additive white Gaussian noise (AWGN) channel. In addition, DC power consumption and the transmitted optical power for the two systems are compared. The analytical results are validated through Monte Carlo simulations and the obtained results demonstrate close match. It is shown that LED clipping has significant impact on the performance of both systems and an optimum system design should take into account the OFDM signal power, DC-bias point, and LED dynamic range.
223 citations
TL;DR: The present state and trends in the development of key parts of controlled induction motor drive systems: converter topologies, modulation methods, as well as control and estimation techniques are reviewed.
Abstract: This article reviews the present state and trends in the development of key parts of controlled induction motor drive systems: converter topologies, modulation methods, as well as control and estimation techniques. Two- and multilevel voltage-source converters, current-source converters, and direct converters are described. The main part of all the produced electric energy is used to feed electric motors, and the conversion of electrical power into mechanical power involves motors ranges from less than 1 W up to several dozen megawatts.
212 citations
TL;DR: A highly conductive electron accumulation layer which is induced by an external DC "gate" voltage is introduced and demonstrated for the first time data encoding with an SOH electro-optic modulator.
Abstract: CMOS-compatible optical modulators are key components for future silicon-based photonic transceivers. However, achieving low modulation voltage and high speed operation still remains a challenge. As a possible solution, the silicon-organic hybrid (SOH) platform has been proposed. In the SOH approach the optical signal is guided by a silicon waveguide while the electro-optic effect is provided by an organic cladding with a high χ(2)-nonlinearity. In these modulators the optical nonlinear region needs to be connected to the modulating electrical source. This requires electrodes, which are both optically transparent and electrically highly conductive. To this end we introduce a highly conductive electron accumulation layer which is induced by an external DC “gate” voltage. As opposed to doping, the electron mobility is not impaired by impurity scattering. This way we demonstrate for the first time data encoding with an SOH electro-optic modulator. Using a first-generation device at a data-rate of 42.7 Gbit/s, widely open eye diagrams were recorded. The measured frequency response suggests that significantly larger data rates are feasible.
207 citations
01 Jun 2011
TL;DR: In this paper, the blue part of the optical spectrum was detected and a discrete multi-tone modulation was applied to achieve a data rate exceeding 100 Mbit/s. The data rate was achieved using a phosphorescent white-light LED in a lighting-like scenario.
Abstract: Wireless transmission exceeding 100 Mbit/s is demonstrated using a phosphorescent white-light LED in a lighting-like scenario. The data rate was achieved by detecting the blue part of the optical spectrum and applying discrete multi-tone modulation.
206 citations
TL;DR: The results demonstrate the viability of incorporating metamaterials into mature semiconductor technologies and establish a new path toward achieving electrically tunable terahertz devices.
Abstract: We present a computational and experimental study of a novel terahertz (THz) device resulting from hybridization of metamaterials with pseudomorphic high electron mobility transistors (HEMTs), fabricated in a commercial gallium arsenide (GaAs) process. Monolithic integration of transistors into each unit cell permits modulation at the metamaterial resonant frequency of 0.46 THz. Characterization is performed using a THz time-domain spectrometer (THz-TDS) and we demonstrate switching values over 30%, and THz modulation at frequencies up to 10 megahertz (MHz). Our results demonstrate the viability of incorporating metamaterials into mature semiconductor technologies and establish a new path toward achieving electrically tunable THz devices.
TL;DR: The proposed all-optical switching concept fulfills all criteria for a useful optical transistor in [Nat. Photon. 4, 3 (2010)], in particular, fan-out and cascadability, which have previously proven as the most difficult to meet.
Abstract: A novel concept for an all-optical transistor is proposed and verified numerically. This concept relies on cross-phase modulation between a signal and a control pulse. Other than previous approaches, the interaction length is extended by temporally locking control and the signal pulse in an optical event horizon, enabling continuous modification of the central wavelength, energy, and duration of a signal pulse by an up to sevenfold weaker control pulse. Moreover, if the signal pulse is a soliton it may maintain its solitonic properties during the switching process. The proposed all-optical switching concept fulfills all criteria for a useful optical transistor in [Nat. Photon. 4, 3 (2010)], in particular, fan-out and cascadability, which have previously proven as the most difficult to meet.
Patent•
14 Jan 2011TL;DR: In this article, a method for transmitting a signal via physical uplink control channel (PUCCH) in a wireless communication system and an apparatus for performing the method are provided.
Abstract: A method for transmitting a signal via physical uplink control channel (PUCCH) in a wireless communication system and an apparatus for performing the method are provided. Control information bits are modulated to generate N1 modulation symbols, wherein N1 is twice a number of subcarriers in one resource block (RB). The modulation symbols are spread by using various orthogonal codes to generate a plurality of sequences and the generated plurality of sequences are transmitted using different slots of a subframe through different antenna ports, each sequence of the plurality of sequences being mapped on a corresponding single carrier frequency division multiple access symbol in a corresponding slot.
15 May 2011
TL;DR: The studies show that, when appropriately designed, the pre-SSK and APM invoked can enhance each other, resulting in that the PSM is capable of attaining a better BER performance than the corresponding pure pre- SSK and pure APM.
Abstract: This paper proposes and studies a transmitter preprocessing aided spatial modulation (PSM) scheme, which conveys information jointly by a conventional amplitude-phase modulation (APM) and a preprocessing aided space shift keying (pre-SSK) modulation. In contrast to the existing SSK modulation, which carries information using the indexes of transmitter antennas and assumes channel state information at receiver (CSIR), the pre-SSK modulation extracts the transmitted information using the indexes of receive antennas and assumes channel state information at transmitter (CSIT). This paper addresses the issues of preprocessing optimization and detection of PSM signals. Furthermore, the bit-error-rate (BER) performance of the PSM is investigated, when assuming that the channel from any transmit antenna to any receive antenna experiences independent Rayleigh fading. Our studies show that, when appropriately designed, the pre-SSK and APM invoked can enhance each other, resulting in that the PSM is capable of attaining a better BER performance than the corresponding pure pre-SSK and pure APM.
TL;DR: Simulation results show that the proposed adaptive SM scheme provides considerable system performance improvement compared to original SM system.
Abstract: In this letter, an adaptive spatial modulation (ASM) transmission scheme is proposed to achieve better system performance under a fixed data rate. The proposed scheme is based on a developed modulation order selection criterion (MOSC), so as to minimize the conditioned pairwise error probability (PEP) for each channel realization. Furthermore, the special information-conveying mode of spatial modulation (SM) is utilized to reduce the complexity of the proposed algorithm. Simulation results show that the proposed adaptive SM scheme provides considerable system performance improvement compared to original SM system.
TL;DR: In this article, a new class of materials that are capable of color tunability over 300 nm with a 15 °C temperature change is introduced, which are assembled from thermoresponsive poly (N-isopropylacrylamide)-co-acrylic acid (pNIPAm-co-AAc) microgels.
Abstract: A new class of materials that are capable of color tunability over 300 nm with a 15 °C temperature change is introduced. The materials are assembled from thermoresponsive poly (N-isopropylacrylamide)-co-acrylic acid (pNIPAm-co-AAc) microgels, which are deposited on Au coated glass substrates. The films are also pH responsive; the temperature-induced color change was suppressed at high pH and is consistent with the behavior of a solution of suspended microgels. The mechanism proposed to account for the observed optical properties suggests that they result from the two Au layers being separated from each other by the “monolithic” microgel film, much like a Fabry-Perot etalon or interferometer. It is the modulation of the distance between these two layers, facilitated by the microgel collapse transition at high temperature, that allows the color to be tuned. The sensitivity of the system presented here will be used for future sensing and biosensing applications, as well as for light filtering applications.
Patent•
05 Jan 2011
TL;DR: In this article, a photo-sensitive detection region is proposed for converting an electromagnetic wave field into an electric signal of flowing charges, and a separated demodulation region with at least two output nodes (D10, D20) and means (IG10, DG10, IG20, DG20) for sampling the charge-current signal at at least 2 different time intervals within a modulation period.
Abstract: A new pixel in semiconductor technology comprises a photo-sensitive detection region (1) for converting an electromagnetic wave field into an electric signal of flowing charges, a separated demodulation region (2) with at least two output nodes (D10, D20) and means (IG10, DG10, IG20, DG20) for sampling the charge-current signal at at least two different time intervals within a modulation period. A contact node (K2) links the detection region (1) to the demodulation region (2). A drift field accomplishes the transfer of the electric signal of flowing charges from the detection region to the contact node. The electric signal of flowing charges is then transferred from the contact node (K2) during each of the two time intervals to the two output nodes allocated to the respective time interval. The separation of the demodulation and the detection regions provides a pixel capable of demodulating electromagnetic wave field at high speed and with high sensitivity.
Patent•
AT&T1
TL;DR: In this article, a method and system for providing broadband access to a data network via gas pipes is described, which utilizes Orthogonal Frequency-Division Multiplexing (OFDM) or Frequency Division Multiplex (FDM) as a modulation technique in order to protect against the effects of dispersion in the gas pipes.
Abstract: A method and system for providing broadband access to a data network via gas pipes is disclosed. Embodiments of the present invention utilize Orthogonal Frequency-Division Multiplexing (OFDM) or Frequency-Division Multiplexing (FDM) as a modulation technique in order to protect against the effects of dispersion in the gas pipes. An OFDM transceiver modulates a digital data stream into an OFDM signal, RF up-converts the OFDM signal, and transmits the RF up-converted OFDM modulated signal through a gas pipe.
TL;DR: In this article, a general algorithm is proposed and adapted for dealing with the control of the three-level NPC inverter and also the Z-source converter, and experimental results corroborate the proposed technique.
Abstract: This article reviews the nonsinusoidal CPWM and SVPWM techniques and deals with the three possibilities of calculation of pulsewidths after the addition of a zero-sequence signal. A general algorithm is proposed and adapted for dealing with the control of the three-level NPC inverter and also the Z-source converter. Experimental results corroborate the proposed technique.
TL;DR: In this paper, the authors report the successful transmission of 64 Tb/s capacity (640 ×107 Gb/S with 12.5 GHz channel spacing) over 320 km reach utilizing 8-THz of spectrum in the C+L -bands at a net spectral efficiency of 8 bit/s/Hz.
Abstract: We report the successful transmission of 64 Tb/s capacity (640 ×107 Gb/s with 12.5 GHz channel spacing) over 320 km reach utilizing 8-THz of spectrum in the C+L -bands at a net spectral efficiency of 8 bit/s/Hz. Such a result is accomplished by the use of raised-cosine pulse-shaped PDM-36QAM modulation, intradyne detection, both pre- and post-transmission digital equalization, and ultra-large-area fiber. We discuss in detail the digital modulation technology and signal processing algorithms used in the experiment, including a new two-stage, blind frequency-search-based frequency-offset estimation algorithm and a more computationally efficient carrier-phase recovery algorithm.
TL;DR: In this paper, the modulation formats for serial optical transmission of 100-Gbit/s and beyond are reviewed. And the main characteristics of modulation formats and application areas of transport technologies for future networks are discussed.
TL;DR: A paper on long-haul analog photonics is presented using theory and experimental results, including intensity modulation with direct detection, phase modulation with interferometric demodulation, and suppressed-carried techniques.
Abstract: A paper on long-haul analog photonics is presented using theory and experimental results. Various analog fiber-optic modulation formats are reviewed, including intensity modulation with direct detection, phase modulation with interferometric demodulation, and suppressed-carried techniques. Modulation linearization methods are reviewed. The limitations of and requirements for photodiode detectors are described.
07 Jul 2011
TL;DR: In this paper, a modulation method for the modular multilevel converter is proposed based on a fixed pulse pattern, where harmonic elimination methods can be applied to the pulse pattern without measuring the capacitor voltages or using any other form of feedback control.
Abstract: This paper presents a new modulation method for the modular multilevel converter. The proposed method is based on a fixed pulse pattern where harmonic elimination methods can be applied. Modulation methods with harmonic elimination based on calculated pulse patterns have been presented for other multilevel topologies. However, similar modulation schemes have not yet been presented for the modular multilevel topology. In the proposed modulation method, the pulse pattern is chosen in such a way that the stored energy in each submodule remains stable. It is shown that this can be done at the fundamental switching frequency without measuring the capacitor voltages or using any other form of feedback control. Such a modulation scheme has not been presented before. The theoretical results are verified by both simulations and experimental results. The simulation results show successful operation at the fundamental switching frequency with a larger number of submodules. When a smaller number of submodules are used, harmonic elimination methods may be applied. This is verified experimentally on a converter with eight submodules per phase leg. The experimental results verify that stable operation can be maintained at the fundamental switching frequency while successfully eliminating the fifth harmonic in the ac-side voltage.
TL;DR: In this paper, the authors discuss the positive indications of a possible dark matter signal in direct detection experiments in terms of a mechanism of interaction between the dark matter particle and the nuclei occurring via the exchange of a light mediator, resulting in a long-range interaction.
Abstract: We discuss the positive indications of a possible dark matter signal in direct detection experiments in terms of a mechanism of interaction between the dark matter particle and the nuclei occurring via the exchange of a light mediator, resulting in a long-range interaction. We analyze the annual modulation results observed by the DAMA and CoGeNT experiments and the observed excess of events of CRESST. In our analysis, we discuss the relevance of uncertainties related to the velocity distribution of galactic dark matter and to the channeling effect in NaI. We find that a long-range force is a viable mechanism, which can provide full agreement between the reconstructed dark matter properties from the various experimental data sets, especially for masses of the light mediator in the 10--30 MeV range and a light dark matter with a mass around 10 GeV. The relevant bounds on the light mediator mass and scattering cross section are then derived, should the annual modulation effects be due to this class of long-range forces.
TL;DR: In this paper, the authors proposed two improved natural balancing strategies for flying capacitor multicell inverters under the standard phase disposition (PD) scheme, which use the same (n - 1) carrier signals as used in the standard PD scheme.
Abstract: The flying capacitor multicell inverter (FCMI) possesses natural balancing property. With the phase-shifted carrier-based scheme, natural balancing can be achieved in a straightforward manner. However, to achieve natural balancing with the harmonically optimal phase-disposition (PD) carrier-based scheme, the conventional approaches require (n - 1) × (n - 1) trapezoidal carrier signals for an n-level inverter, which is ( n - 1) × (n - 2) times more than that in the standard PD scheme. This paper proposes two improved natural balancing strategies for FCMI under PD scheme, which use the same (n - 1) carrier signals as used in the standard PD scheme. In the first scheme, the on-line detections are performed of (i) the band in which the modulation signal is located, (ii) corresponding period number of the carrier, and (iii) rising or falling half cycle of the carrier waveform to generate the switching signals based on certain rules. In the second strategy, the output voltage level selection is first processed and the switching signals are then generated according to a rule based on preferential cell selection algorithm. These methods are easy to use and can be simply implemented as compared to the other available methods. Simulation and experimental results are presented for a five-level inverter to verify these proposed schemes.
TL;DR: In this paper, a radio-frequency and bit-rate scalable technique for multigigabit wireless signal generation based on all-optical orthogonal frequency-division multiplexing (OFDM) and photonic up-conversion is presented.
Abstract: We present a radio-frequency (RF) and bit-rate scalable technique for multigigabit wireless signal generation based on all-optical orthogonal frequency-division multiplexing (OFDM) and photonic up-conversion. Coherent detection supported by digital signal processing is used for signal demodulation and data recovery. In order to demonstrate the RF frequency scalability and bit-rate transparency, the system is tested at 60 GHz and in the 75- to 110-GHz band at the baud rates of 5 and 10 Gbaud. In terms of the bit rate, the proposed system is experimentally tested up to 40 Gb/s for wireless signal generation and demodulation. The wireless transmission is not considered in this letter. Additionally, a novel digital carrier phase/frequency recovery structure is employed to enable robust phase and frequency tracking between the beating lasers.
TL;DR: An all-fiber approach to generate triangular-shaped pulses based on frequency-to-time conversion is proposed and demonstrated and can be tuned by adjusting the modulation rate and the dispersion value, respectively.
Abstract: An all-fiber approach to generate triangular-shaped pulses based on frequency-to-time conversion is proposed and demonstrated. Two filter modules that have sinusoidal spectral responses are cascaded to create a triangular-shaped optical spectrum. Through the frequency-to-time conversion in a dispersive fiber, periodic triangular pulses with the same shape as the optical spectrum are obtained. The repetition rate and pulse width of the generated signals can be tuned by adjusting the modulation rate and the dispersion value, respectively.
TL;DR: This in-depth tutorial clarified myths and facts about non-bijective modulation, focusing on superposition modulation (SM).
Abstract: Traditionally, digital modulation schemes are bijective (i.e., the signal constellation points are disjunct), and the mapping is unique. Only recently it has been discovered that non-bijective modulation schemes may outperform bijective modulation schemes when employed in conjunction with suitable channel coding and iterative processing. In this in-depth tutorial, we clarify myths and facts about non-bijective modulation. Emphasis is on superposition modulation (SM). Without active signal shaping, SM outperforms bit-interleaved coded modulation with PSK or square QAM modulation at even lower receiver complexity.
TL;DR: In this article, four different sequential switching hybrid-modulation strategies were compared for cascaded multilevel inverters and the main characteristic of these modulations are the reduction of switching losses with good harmonic performance, balanced power loss dissipation among the devices with in a cell, and among the series-connected cells.
Abstract: This paper presents four different sequential switching hybrid-modulation strategies and compared for cascaded multilevel inverters. Hybrid-modulation strategies represent combinations of fundamental-frequency modulation and multilevel sinusoidal-modulation (MSPWM) strategies, and are designed for performance of the well-known alternative phase opposition disposition, phase-shifted carrier, carrier-based space-vector modulation, and single-carrier sinusoidal-modulations. The main characteristic of these modulations are the reduction of switching losses with good harmonic performance, balanced power loss dissipation among the devices with in a cell, and among the series-connected cells. MSPWM and its base modulator design are implemented on a TMS320F2407 digital signal processor (DSP). Complex programmable logic device realizes hybrid-modulation algorithm with base pulsewidth modulation (PWM) circulation, and is integrated with DSP for sequential switching hybrid PWM generation. The proposed modulations can be easily extended to three phase, and higher level inverters, operates with same physical structure of the power module. The feasibility of these hybrid modulations are verified through spectral analysis, power loss analysis, simulation, and experimental results.
TL;DR: In this paper, an optical modulator that consists of an integrated dual parallel Mach-Zehnder modulator (dMZM) can be used for obtaining not only optical single-side band modulation but also tunability of optical carrier to sideband ratio (OCSR) simultaneously.
Abstract: We show that an optical modulator that consists of an integrated dual parallel Mach-Zehnder modulator (dMZM) can be used for obtaining not only optical single-side band modulation but also tunability of optical carrier to sideband ratio (OCSR) simultaneously. Such a modulator will be vital for optimizing the performance of radio over fiber links by improving modulation efficiency and receiver sensitivity and by removing fiber chromatic dispersion induced RF power fading. It is shown that a wide range of OCSR tunability can be obtained by altering bias voltage of dMZM, and optimum OCSR, to maximize the output RF power, depends on RF modulation index and extinction ratio of the integrated dMZM. Good agreement between theory, simulation, and experiment is obtained. For typical extinction ratio and low modulation index, it is found that an OCSR of 0 dB is optimum to maximize RF carrier power. However, for multiband orthogonal frequency-division multiplexing (MB-OFDM) ultra-wideband (UWB) radio, the best error vector magnitude (EVM) of -21.8 dB is obtained experimentally at an OCSR of ~5.4 dB due to avoidance of clipping induced nonlinear distortion.