Topic
Oblique shock
About: Oblique shock is a research topic. Over the lifetime, 6551 publications have been published within this topic receiving 119823 citations.
Papers published on a yearly basis
Papers
More filters
••
TL;DR: In this paper, two-dimensional hybrid simulations of curved collisionless supercritical shocks, retaining both quasi-perpendicular and quasi-parallel sections of the shock in order to study the character and origin of the foreshock ion population are presented.
Abstract: Results are presented from two-dimensional hybrid simulations of curved collisionless supercritical shocks, retaining both quasi-perpendicular and quasi-parallel sections of the shock in order to study the character and origin of the foreshock ion population. The simulations demonstrate that the foreshock ion population is dominated by ions impinging upon the quasi-parallel side of the shock, while nonlocal transport from the quasi-perpendicular side of the shock into the foreshock region is minimal. Further, it is shown that the ions gain energy by drifting significantly in the direction of the convection electric field through multiple shock encounters.
35 citations
••
01 Jan 1994TL;DR: In this article, the authors proposed to enhance the rate of mixing and combustion of hydrogen and air, and thereby reduce combustor length through the introduction of streamwise vorticity generated by the interaction of a weak oblique shock wave with the density gradient between air and a cylindrical jet of hydrogen.
Abstract: To promote efficient performance of very high speed air-breathing propulsion systems, the combustor Mach number must be of the order of six for a flight Mach number of 18. Because of this high gas speed through the combustor, mixing rates of hydrogen fuel with air must be very rapid in order to allow a combustor of reasonable length. It is proposed to enhance the rate of mixing and combustion of hydrogen and air, and thereby reduce combustor length, through the introduction of streamwise vorticity generated by the interaction of a weak oblique shock wave with the density gradient between air and a cylindrical jet of hydrogen.
Because of the high Mach number flow in the combustor, the oblique shock traverses the jet at a small angle with respect to the free stream direction, and the principle of slender body theory allows one conceptually to replace the three-dimensional steady flow with a two-dimensional unsteady flow. As a consequence, two-dimensional time-dependent computational studies and an extensive experimental shock tube investigation were employed to assess mixing rates for the steady flow in the combustor. The results indicated that under realistic conditions, adequate mixing could be accomplished within 1 ms, a rate that was technologically interesting.
Encouraged by these experiments, a “practical” injector, utilizing shock-enhanced mixing, was designed for a combustor having a free stream Mach number of 6.0. A detailed aerodynamic and mixing investigation was carried out in the Mach 6 High Reynolds Number Tunnel at the NASA-Langley Research Center. The results confirmed both the details and the overall effectiveness of the shock-enhanced mixing concept.
35 citations
••
TL;DR: In this article, the authors modeled the circumplanetary flow of Io's SO 2 atmosphere using the direct simulation Monte Carlo (DSMC) method and found that, except in the subsolar region, the flows are predominately rarefied.
35 citations
01 May 2010
TL;DR: In this paper, the application of vortex generators for flow control in an external compression axisymmetric, low-boom concept inlet was investigated using RANS simulations with three-dimensional (3-D), structured, chimera (overset) grids and the WIND-US code.
Abstract: The application of vortex generators for flow control in an external compression, axisymmetric, low-boom concept inlet was investigated using RANS simulations with three-dimensional (3-D), structured, chimera (overset) grids and the WIND-US code. The low-boom inlet design is based on previous scale model 1- by 1-ft wind tunnel tests and features a zero-angle cowl and relaxed isentropic compression centerbody spike, resulting in defocused oblique shocks and a weak terminating normal shock. Validation of the methodology was first performed for micro-ramps in supersonic flow on a flat plate with and without oblique shocks. For the inlet configuration, simulations with several types of vortex generators were conducted for positions both upstream and downstream of the terminating normal shock. The performance parameters included incompressible axisymmetric shape factor, separation area, inlet pressure recovery, and massflow ratio. The design of experiments (DOE) methodology was used to select device size and location, analyze the resulting data, and determine the optimal choice of device geometry. The optimum upstream configuration was found to substantially reduce the post-shock separation area but did not significantly impact recovery at the aerodynamic interface plane (AIP). Downstream device placement allowed for fuller boundary layer velocity profiles and reduced distortion. This resulted in an improved pressure recovery and massflow ratio at the AIP compared to the baseline solid-wall configuration.
35 citations
••
35 citations