Overall pressure ratio

About: Overall pressure ratio is a research topic. Over the lifetime, 4479 publications have been published within this topic receiving 50180 citations.

Using Hydrogen as Gas Turbine Fuel

Abstract: This paper addresses the possibility to burn hydrogen in a large size, heavy-duty gas turbine designed to run on natural gas as a possible short-term measure to reduce greenhouse emissions of the power industry. The process used to produce hydrogen is not discussed here: we mainly focus on the behavior of the gas turbine by analyzing the main operational aspects related to switching from natural gas to hydrogen. We will consider the effects of variations of volume flow rate and of thermophysical properties on the matching between turbine and compressor and on the blade cooling of the hot rows of the gas turbine. In the analysis we will take into account that those effects are largely emphasized by the abundant dilution of the fuel by inert gases (steam or nitrogen), necessary to control the NO x emissions. Three strategies will be considered to adapt the original machine, designed to run on natural gas, to operate properly with diluted hydrogen: variable guide vane (VGV) operations, increased pressure ratio, re-engineered machine. The performance analysis, carried out by a calculation method including a detailed model of the cooled gas turbine expansion, shows that moderate efficiency decays can be predicted with elevated dilution rates (nitrogen is preferable to steam under this point of view). The combined cycle power output substantially increases if not controlled by VGV operations. It represents an opportunity if some moderate re-design is accepted (turbine blade height modifications or high-pressure compressor stages addition).

Numerical investigation of the physics of rotating-detonation-engines

Abstract: Rotating-detonation-engines (RDE’s) represent an alternative to the extensively studied pulse-detonation-engines (PDE’s) for obtaining propulsion from the high efficiency detonation cycle. Since it has received considerably less attention, the general flow-field and effect of parameters such as stagnation conditions and back pressure on performance are less well understood than for PDE’s. In this article we describe results from time-accurate calculations of RDE’s using algorithms that have successfully been used for PDE simulations previously. Results are obtained for stoichiometric hydrogen–air RDE’s operating at a range of stagnation pressures and back pressures. Conditions within the chamber are described as well as inlet and outlet conditions and integrated quantities such as total mass flow, force, and specific impulse. Further computations examine the role of inlet stagnation pressure and back pressure on detonation characteristics and engine performance. The pressure ratio is varied between 2.5 and 20 by varying both stagnation and back pressure to isolate controlling factors for the detonation and performance characteristics. It is found that the detonation wave height and mass flow rate are determined primarily by the stagnation pressure, whereas overall performance is closely tied to pressure ratio. Specific impulses are calculated for all cases and range from 2872 to 5511 s, and are lowest for pressure ratios below 4. The reason for performance loss is shown to be associated with the secondary shock wave structure that sets up in the expansion portion of the RDE, which strongly effects the flow at low pressure ratios. Expansion to supersonic flow behind the detonation front in RDE’s with higher pressure ratios isolate the detonation section of the RDE and thus limit the effect of back pressure on the detonation characteristics.

Turboelectric Distributed Propulsion Engine Cycle Analysis for Hybrid-Wing-Body Aircraft

Abstract: Meeting NASA's N+3 goals requires a fundamental shift in approach to aircraft and engine design. Material and design improvements allow higher pressure and higher temperature core engines which improve the thermal efficiency. Propulsive efficiency, the other half of the overall efficiency equation, however, is largely determined by the fan pressure ratio (FPR). Lower FPR increases propulsive efficiency, but also dramatically reduces fan shaft speed through the combination of larger diameter fans and reduced fan tip speed limits. The result is that below an FPR of 1.5 the maximum fan shaft speed makes direct drive turbines problematic. However, it is the low pressure ratio fans that allow the improvement in propulsive efficiency which, along with improvements in thermal efficiency in the core, contributes strongly to meeting the N+3 goals for fuel burn reduction. The lower fan exhaust velocities resulting from lower FPRs are also key to meeting the aircraft noise goals. Adding a gear box to the standard turbofan engine allows acceptable turbine speeds to be maintained. However, development of a 50,000+ hp gearbox required by fans in a large twin engine transport aircraft presents an extreme technical challenge, therefore another approach is needed. This paper presents a propulsion system which transmits power from the turbine to the fan electrically rather than mechanically. Recent and anticipated advances in high temperature superconducting generators, motors, and power lines offer the possibility that such devices can be used to transmit turbine power in aircraft without an excessive weight penalty. Moving to such a power transmission system does more than provide better matching between fan and turbine shaft speeds. The relative ease with which electrical power can be distributed throughout the aircraft opens up numerous other possibilities for new aircraft and propulsion configurations and modes of operation. This paper discusses a number of these new possibilities. The Boeing N2 hybrid-wing-body (HWB) is used as a baseline aircraft for this study. The two pylon mounted conventional turbofans are replaced by two wing-tip mounted turboshaft engines, each driving a superconducting generator. Both generators feed a common electrical bus which distributes power to an array of superconducting motor-driven fans in a continuous nacelle centered along the trailing edge of the upper surface of the wing-body. A key finding was that traditional inlet performance methodology has to be modified when most of the air entering the inlet is boundary layer air. A very thorough and detailed propulsion/airframe integration (PAI) analysis is required at the very beginning of the design process since embedded engine inlet performance must be based on conditions at the inlet lip rather than freestream conditions. Examination of a range of fan pressure ratios yielded a minimum Thrust-specific-fuel-consumption (TSFC) at the aerodynamic design point of the vehicle (31,000 ft /Mach 0.8) between 1.3 and 1.35 FPR. We deduced that this was due to the higher pressure losses prior to the fan inlet as well as higher losses in the 2-D inlets and nozzles. This FPR is likely to be higher than the FPR that yields a minimum TSFC in a pylon mounted engine. 1