Overpressure

About: Overpressure is a research topic. Over the lifetime, 3236 publications have been published within this topic receiving 34648 citations.

The role of the stress regime on microseismicity induced by overpressure and cooling in geologic carbon storage

Abstract: Fluid injection in deep geological formations usually induces microseismicity. In particular, industrial-scale injection of CO2 may induce a large number of microseismic events. Since CO2 is likely to reach the storage formation at a lower temperature than that corresponding to the geothermal gradient, both overpressure and cooling decrease the effective stresses and may induce microseismicity. Here, we investigate the effect of the stress regime on the effective stress evolution and fracture stability when injecting cold CO2 through a horizontal well in a deep saline formation. Simulation results show that when only overpressure occurs, the vertical total stress remains practically constant, but the horizontal total stresses increase proportionally to overpressure. These hydro-mechanical stress changes result in a slight improvement in fracture stability in normal faulting stress regimes because the decrease in deviatoric stress offsets the decrease in effective stresses produced by overpressure. However, fracture stability significantly decreases in reverse faulting stress regimes because the size of the Mohr circle increases in addition to being displaced towards failure conditions. Fracture stability also decreases in strike slip stress regimes because the Mohr circle maintains its size and is shifted towards the yield surface a magnitude equal to overpressure minus the increase in the horizontal total stresses. Additionally, cooling induces a thermal stress reduction in all directions, but larger in the out-of-plane direction. This stress anisotropy causes, apart from a displacement of the Mohr circle towards the yield surface, an increase in the size of the Mohr circle. These two effects decrease fracture stability, resulting in the strike slip being the least stable stress regime when cooling occurs, followed by the reverse faulting and the normal faulting stress regimes. Thus, characterizing the stress state is crucial to determine the maximum sustainable injection pressure and maximum temperature drop to safely inject CO2 .

Geological controls on overpressure in the Northern Carnarvon Basin

Abstract: A small, but significant fraction of wells drilled in the Northern Carnarvon Basin have encountered problems with overpressure: better pore pressure prediction would improve safety and economy for drilling operations. In the Northern Carnarvon Basin the occurrence of overpressure and likely mechanisms are under investigation as part of the Australian Petroleum Cooperative Research Centre (APCRC) Research Program on Pore Pressure Prediction. Previous workers have proposed a number of mechanisms as the main cause of overpressure including undercompaction, hydrocarbon generation, horizontal stress and clay reactions. A preliminary regional study was undertaken incorporating over 400 well completion reports which identified approximately 60 wells with mud weights greater than 1.25 S.G. A subset of these wells was investigated and more reliable but much scarcer pressure indicators such as kicks or direct pressure measurements were examined. Depth-pressure profiles of wells across the region are variable and commonly show pressure compartmentalisation. Using a range of indicators, it was observed that overpressured strata in the Barrow Subbasin: occur over a wide depth range (2,500 to 4,000+ mbsl); occur over a wide stratigraphic range (Late Triassic to Late Cretaceous); are not regionally limited by major structural boundaries; are associated with sequences dominated by finegrained sediments with variable clay mineralogy; and in depositionally, or structurally, isolated sandstones; and mainly to the west of the Barrow and Dampier Subbasins around the Alpha Arch and Rankin Trend, coinciding with thickest Tertiary deposition. Previous published work in the study area has tended to support hydrocarbon generation as the primary cause of overpressure, though more recent publications have emphasised compaction disequilibrium. The log response (DT, RHOB and NPHI) of overpressured clay-rich strata has been investigated to constrain the type of overpressure mechanism. A normal compaction trend has been derived for four stratigraphic groupings; Muderong Shale, Barrow Group, Jurassic and Triassic. All overpressure occurrences were accompanied by an increase in sonic transit time. Not all wells have suitable log data for evaluation, but all stratigraphic groups show some evidence of elevated porosity associated with overpressure consistent with disequillibrium compaction as a dominant mechanism. Overpressures in the Barrow Group in Minden-1 and the Jurassic section within Zeepaard–1 do not have accompanying porosity anomalies suggesting a different overpressure mechanism model is needed.

Overpressure valve for the content of a package

Abstract: An overpressure valve for a packaging container is disposed on the inside of the packaging material comprising the packaging container The overpressure valve comprises a base plate, a diaphragm, and a connecting element The overpressure valve is relatively simple in construction and can be produced economically