Topic
Perovskite solar cell
About: Perovskite solar cell is a research topic. Over the lifetime, 4701 publications have been published within this topic receiving 216807 citations. The topic is also known as: PSC.
Papers
More filters
TL;DR: In this article, a 1 cm2 near-infrared transparent perovskite solar cell with 14.5% steady-state efficiency was presented, as compared to 16.4% on 0.25 cm2.
Abstract: Combining market-proven silicon solar cell technology with an efficient wide band gap top cell into a tandem device is an attractive approach to reduce the cost of photovoltaic systems. For this, perovskite solar cells are promising high-efficiency top cell candidates, but their typical device size (<0.2 cm2), is still far from standard industrial sizes. We present a 1 cm2 near-infrared transparent perovskite solar cell with 14.5% steady-state efficiency, as compared to 16.4% on 0.25 cm2. By mechanically stacking these cells with silicon heterojunction cells, we experimentally demonstrate a 4-terminal tandem measurement with a steady-state efficiency of 25.2%, with a 0.25 cm2 top cell. The developed top cell processing methods enable the fabrication of a 20.5% efficient and 1.43 cm2 large monolithic perovskite/silicon heterojunction tandem solar cell, featuring a rear-side textured bottom cell to increase its near-infrared spectral response. Finally, we compare both tandem configurations to identify effic...
329 citations
TL;DR: In this article, a nanoporous Mo-doped BiVO4 (Mo:BiVO4) was used for photoelectrochemical (PEC) water splitting, which achieved a high water-splitting photocurrent of 5.82 ± 0.36 mA cm−2 at 1.23 V versus the reversible hydrogen electrode under 1-sun illumination.
Abstract: Bismuth vanadate (BiVO4) has been widely regarded as a promising photoanode material for photoelectrochemical (PEC) water splitting because of its low cost, its high stability against photocorrosion, and its relatively narrow band gap of 2.4 eV. However, the achieved performance of the BiVO4 photoanode remains unsatisfactory to date because its short carrier diffusion length restricts the total thickness of the BiVO4 film required for sufficient light absorption. We addressed the issue by deposition of nanoporous Mo-doped BiVO4 (Mo:BiVO4) on an engineered cone-shaped nanostructure, in which the Mo:BiVO4 layer with a larger effective thickness maintains highly efficient charge separation and high light absorption capability, which can be further enhanced by multiple light scattering in the nanocone structure. As a result, the nanocone/Mo:BiVO4/Fe(Ni)OOH photoanode exhibits a high water-splitting photocurrent of 5.82 ± 0.36 mA cm−2 at 1.23 V versus the reversible hydrogen electrode under 1-sun illumination. We also demonstrate that the PEC cell in tandem with a single perovskite solar cell exhibits unassisted water splitting with a solar-to-hydrogen conversion efficiency of up to 6.2%.
328 citations
TL;DR: In this paper, it was shown that the presence of unreacted PbI2 results in an intrinsic instability of the perovskite film under illumination, leading to the film degradation under inert atmosphere and faster degradation upon exposure to illumination and humidity.
Abstract: Unreacted lead iodide is commonly believed to be beneficial to the efficiency of methylammonium lead iodide perovskite based solar cells, since it has been proposed to passivate the defects in perovskite grain boundaries. However, it is shown here that the presence of unreacted PbI2 results in an intrinsic instability of the film under illumination, leading to the film degradation under inert atmosphere and faster degradation upon exposure to illumination and humidity. The perovskite films without lead iodide have improved stability, but lower efficiency due to inferior film morphology (smaller grain size, the presence of pinholes). Optimization of the deposition process resulted in PbI2-free perovskite films giving comparable efficiency to those with excess PbI2 (14.2 ± 1.3% compared to 15.1 ± 0.9%) Thus, optimization of the deposition process for PbI2-free films leads to dense, pinhole-free, large grain size perovskite films which result in cells with high efficiency without detrimental effects on the film photostability caused by excess PbI2. However, it should be noted that for encapsulated devices illuminated through the substrate (fluorine-doped tin oxide glass, TiO2 film), film photostability is not a key factor in the device degradation.
323 citations
TL;DR: In this article, the impact of Cs dopant on the optoelectronic properties of NiOx and the photovoltaic performance has been investigated in inverted planar perovskite solar cells.
Abstract: Organic–inorganic hybrid perovskite solar cells have resulted in tremendous interest in developing next generation photovoltaics due to high record efficiency exceeding 22%. For inverted structure perovskite solar cells, the hole extraction layers play a significant role in achieving efficient and stable perovskite solar cell by modifying charge extraction, interfacial recombination losses, and band alignment. Here, cesium doped NiOx is selected as a hole extraction layer to study the impact of Cs dopant on the optoelectronic properties of NiOx and the photovoltaic performance. Cs doped NiOx films are prepared by a simple solution-based method. Both doped and undoped NiOx films are smooth and highly transparent, while the Cs doped NiOx exhibits better electron conductivity and higher work function. Therefore, Cs doping results in a significant improvement in the performance of NiOx-based inverted planar perovskite solar cells. The best efficiency of Cs doped NiOx devices is 19.35%, and those devices show high stability as well. The improved efficiency in devices with Cs:NiOx is attributed to a significant improvement in the hole extraction and better band alignment compared to undoped NiOx. This work reveals that Cs doped NiOx is very promising hole extraction material for high and stable inverted perovskite solar cells.
318 citations
TL;DR: Graphdiyne (GD), a novel two dimension carbon material, is doped into PCBM layer of perovskite solar cell with an inverted structure to improve the electron transport and bring the high PCE of the devices and the data repeatability.
Abstract: Organic–inorganic perovskite solar cells have recently emerged at the forefront of photovoltaics research. Here, for the first time, graphdiyne (GD), a novel two dimension carbon material, is doped into PCBM layer of perovskite solar cell with an inverted structure (ITO/PEDOT:PSS/CH3NH3PbI3–xClx/PCBM:GD/C60/Al) to improve the electron transport. The optimized PCE of 14.8% was achieved. Also, an average power conversion efficiency (PCE) of PCBM:GD-based devices was observed with 28.7% enhancement (13.9% vs 10.8%) compared to that of pure PCBM-based ones. According to scanning electron microscopy, conductive atomic force microscopy, space charge limited current, and photoluminescence quenching measurements, the enhanced current density and fill factor of PCBM:GD-based devices were ascribed to the better coverage on the perovskite layer, improved electrical conductivity, strong electron mobility, and efficient charge extraction. Small hysteresis and stable power output under working condition (14.4%) have al...
318 citations