Polycarbonate

About: Polycarbonate is a research topic. Over the lifetime, 14032 publications have been published within this topic receiving 141740 citations. The topic is also known as: PC & Polycarbonate, PC.

Toughening of a highly cross‐linked epoxy resin by reactive blending with bisphenol A polycarbonate. I. FTIR spectroscopy

Abstract: A highly cross-linked thermosetting epoxy resin was modified by a reactive blending process carried out in the presence of bisphenol A polycarbonate (PC). Prior to the curing process the PC component was dissolved at high temperature in the uncured epoxy matrix. FTIR investigation of this reactive mixture demonstrated the occurrence of physical and chemical interactions among the blend components. Isothermal kinetic measurements performed by FTIR spectroscopy showed that the presence of PC does not affect the overall curing mechanism but decreases both the initial reaction rate and the final conversion of reactants. © 1994 John Wiley & Sons, Inc.

High-pressure sorption of carbon dioxide in solvent-cast poly(methyl methacrylate) and poly(ethyl methacrylate) films

Abstract: Carbon dioxide sorption isotherms in poly(methyl methacrylate) (PMMA) and poly(ethyl methacrylate) (PEMA) are reported for pressures up to 20 atm. Temperatures between 35 and 80°C were studied for PMMA and temperatures between 30 and 55°C were studied for PEMA. Typical dual mode sorption isotherms concave to the pressure axis were observed in all cases. The measured Langmuir sorption capacities of both polymers extrapolated to zero at the glass transition (Tg) consistent with the behavior of other glassy polymer/gas systems. Sorption enthalpies for CO2 in the Henry's law mode for PMMA and PEMA are in the same range (−2 to −4 kcal/mole) as has been reported for a variety of other glassy polymers such as poly(ethylene terephthalate), polycarbonate, and polyacrylonitrile. Some of the data suggest that postcasting treatment of the PEMA films left a small amount of residual solvent in the film. the presence of the trace residual solvent during quenching from the rubbery to the glassy state after annealing appears to cause a dilation of the Langmuir capacity and an alteration in the apparent Langmuir affinity constant of the PEMA film. These results suggest the possibility of tailoring physical properties of glassy polymers such as sorptivity, permeability, impact strength, and craze resistance by doping small amounts of selected residuals into polymers prior to quenching to the glassy state from the rubbery state.

Morphology-tensile behavior relationship in injection molded poly(ethylene terephthalate)/polyethylene and polycarbonate/polyethylene blends (I). Part I skin-core structure

Abstract: The skin-core structure of injection molded poly(ethylene terephthalate) (PET)/polyethylene (PE) and polycarbonate (PC)/PE blends was investigated. The results indicate that both shape and size of the PET and PC phases depended not only on the nature properties of PET/PE and PC/PE blends, but also on the injection molding parameters such as injection speed and the positions in the molded bars. The morphology in the section perpendicular to the melt flow direction included four layers, surface, sub-skin, intermediate layers as well as core zone. The surface layer was ignored in the present study. The sub-skin layer contained more or less fibrous structure and its thickness gradually decreased along the molded bar from the gate toward the non-gate end. At the same injection speed, the concentration of the injection-induced fibers in PC/PE blend was much higher than that in PET/PE blend. In the core region, the dispersed phase was mainly composed of spherical particles whose diameter increased along the melt flow pathway. Between these two layers, there was an intermediate layer where the dispersed particles mainly assumed the form of fibers, ellipsoids or spheres. Generally, no matter whether the dispersed particles were elongated or not during injection molding, the PET particles were larger than PC ones.