Power density

About: Power density is a research topic. Over the lifetime, 9534 publications have been published within this topic receiving 197264 citations. The topic is also known as: volumic power & volume power density.

High power electrochemical capacitors based on carbon nanotube electrodes

Abstract: Carbon nanotube sheet electrodes have been prepared from catalytically grown carbon nanotubes of high purity and narrow diameter distribution, centered around 80 A. Our study shows that the electrodes are free-standing mats of entangled nanotubes with an open porous structure almost impossible to obtain with activated carbon or carbon fiber. These properties are highly desirable for high power and long cycle life electrochemical capacitors. Specific capacitances of 102 and 49 F/g were measured at 1 and 100 Hz, respectively, on a single cell device with 38 wt % H2SO4 as the electrolyte. The same cell had a power density of >8000 W/kg.

A micro electromagnetic generator for vibration energy harvesting

Abstract: Vibration energy harvesting is receiving a considerable amount of interest as a means for powering wireless sensor nodes This paper presents a small (component volume 01 cm3, practical volume 015 cm3) electromagnetic generator utilizing discrete components and optimized for a low ambient vibration level based upon real application data The generator uses four magnets arranged on an etched cantilever with a wound coil located within the moving magnetic field Magnet size and coil properties were optimized, with the final device producing 46 µW in a resistive load of 4 k? from just 059 m s-2 acceleration levels at its resonant frequency of 52 Hz A voltage of 428 mVrms was obtained from the generator with a 2300 turn coil which has proved sufficient for subsequent rectification and voltage step-up circuitry The generator delivers 30% of the power supplied from the environment to useful electrical power in the load This generator compares very favourably with other demonstrated examples in the literature, both in terms of normalized power density and efficiency

Status of silicon carbide (SiC) as a wide-bandgap semiconductor for high-temperature applications: A review

Abstract: Silicon carbide (SiC), a material long known with potential for high-temperature, high-power, high-frequency, and radiation hardened applications, has emerged as the most mature of the wide-bandgap (2.0 eV ≲ Eg ≲ 7.0 eV) semiconductors since the release of commercial 6HSiC bulk substrates in 1991 and 4HSiC substrates in 1994. Following a brief introduction to SiC material properties, the status of SiC in terms of bulk crystal growth, unit device fabrication processes, device performance, circuits and sensors is discussed. Emphasis is placed upon demonstrated high-temperature applications, such as power transistors and rectifiers, turbine engine combustion monitoring, temperature sensors, analog and digital circuitry, flame detectors, and accelerometers. While individual device performances have been impressive (e.g. 4HSiC MESFETs with fmax of 42 GHz and over 2.8 W mm−1 power density; 4HSiC static induction transistors with 225 W power output at 600 MHz, 47% power added efficiency (PAE), and 200 V forward blocking voltage), material defects in SiC, in particular micropipe defects, remain the primary impediment to wide-spread application in commercial markets. Micropipe defect densities have been reduced from near the 1000 cm−2 order of magnitude in 1992 to 3.5 cm−2 at the research level in 1995.

Iron-based cathode catalyst with enhanced power density in polymer electrolyte membrane fuel cells

Abstract: H(2)-air polymer-electrolyte-membrane fuel cells are electrochemical power generators with potential vehicle propulsion applications. To help reduce their cost and encourage widespread use, research has focused on replacing the expensive Pt-based electrocatalysts in polymer-electrolyte-membrane fuel cells with a lower-cost alternative. Fe-based cathode catalysts are promising contenders, but their power density has been low compared with Pt-based cathodes, largely due to poor mass-transport properties. Here we report an iron-acetate/phenanthroline/zeolitic-imidazolate-framework-derived electrocatalyst with increased volumetric activity and enhanced mass-transport properties. The zeolitic-imidazolate-framework serves as a microporous host for phenanthroline and ferrous acetate to form a catalyst precursor that is subsequently heat treated. A cathode made with the best electrocatalyst from this work, tested in H(2)-O(2,) has a power density of 0.75 W cm(-2) at 0.6 V, a meaningful voltage for polymer-electrolyte-membrane fuel cells operation, comparable with that of a commercial Pt-based cathode tested under identical conditions.

Graphite Fiber Brush Anodes for Increased Power Production in Air-Cathode Microbial Fuel Cells

Abstract: To efficiently generate electricity using bacteria in microbial fuel cells (MFCs), highly conductive noncorrosive materials are needed that have a high specific surface area (surface area per volume) and an open structure to avoid biofouling. Graphite brush anodes, consisting of graphite fibers wound around a conductive, but noncorrosive metal core, were examined for power production in cube (C-MFC) and bottle (B-MFC) air-cathode MFCs. Power production in C-MFCs containing brush electrodes at 9600 m2/m3 reactor volume reached a maximum power density of 2400 mW/m2 (normalized to the cathode projected surface area), or 73 W/m3 based on liquid volume, with a maximum Coulombic efficiency (CE) of 60%. This power density, normalized by cathode projected area, is the highest value yet achieved by an air-cathode system. The increased power resulted from a reduction in internal resistance from 31 to 8 Ω. Brush electrodes (4200 m2/m3) were also tested in B-MFCs, consisting of a laboratory media bottle modified to h...