Stand-alone power system

About: Stand-alone power system is a research topic. Over the lifetime, 8650 publications have been published within this topic receiving 192397 citations. The topic is also known as: Stand-alone photovoltaic power system.

Enhancement of the REMix energy system model : global renewable energy potentials, optimized power plant siting and scenario validation

Abstract: As electricity generation based on volatile renewable resources is subject to fluctuations, data with high temporal and spatial resolution on their availability is indispensable for integrating large shares of renewable capacities into energy infrastructures. The scope of the present doctoral thesis is to enhance the existing energy modelling environment REMix in terms of (i.) extending the geographic coverage of the potential assessment tool REMix-EnDaT from a European to a global scale, (ii.) adding a new plant siting optimization module REMix-PlaSMo, capable of assessing siting effects of renewable power plants on the portfolio output and (iii.) adding a new alternating current power transmission model between 30 European countries and CSP electricity imports from power plants located in North Africa and the Middle East via high voltage direct current links into the module REMix-OptiMo. With respect to the global potential assessment tool, a thorough investigation is carried out creating an hourly global inventory of the theoretical potentials of the major renewable resources solar irradiance, wind speed and river discharge at a spatial resolution of 0.45°x0.45°. A detailed global land use analysis determines eligible sites for the installation of renewable power plants. Detailed power plant models for PV, CSP, wind and hydro power allow for the assessment of power output, cost per kWh and respective full load hours taking into account the theoretical potentials, technological as well as economic data. The so-obtined tool REMix-EnDaT can be used as follows: First, as an assessment tool for arbitrary geographic locations, countries or world regions, deriving either site-specific or aggregated installable capacities, cost as well as full load hour potentials. Second, as a tool providing input data such as installable capacities and hourly renewable electricity generation for further assessments using the modules REMix-PlasMo and OptiMo. The plant siting tool REMix-PlaSMo yields results as to where the volatile power technologies photovoltaics and wind are to be located within a country in order to gain distinct effects on their aggregated power output. Three different modes are implemented: (a.) Optimized plant siting in order to obtain the cheapest generation cost, (b.) a minimization of the photovoltaic and wind portfolio output variance and (c.) a minimization of the residual load variance. The third fundamental addition to the REMix model is the amendment of the module REMix-OptiMo with a new power transmission model based on the DC load flow approximation. Moreover, electricity imports originating from concentrating solar power plants located in North Africa and the Middle East are now feasible. All of the new capabilities and extensions of REMix are employed in three case studies: In case study 1, using the module REMix-EnDaT, a global potential assessment is carried out for 10 OECD world regions, deriving installable capacities, cost and full load hours for PV, CSP, wind and hydro power. According to the latter, photovoltaics will represent the cheapest technology in 2050, an average of 1634 full load hours could lead to an electricity generation potential of some 5500 PWh. Although CSP also taps solar irradiance, restrictions in terms of suitable sites for erecting power plants are more severe. For that reason, the maximum potential amounts to some 1500 PWh. However, thermal energy storage can be used, which, according to this assessment, could lead to 5400 hours of full load operation. Onshore wind power could tap a potential of 717 PWh by 2050 with an average of 2200 full load hours while offshore, wind power plants could achieve a total power generation of 224 PWh with an average of 3000 full load hours. The electricity generation potential of hydro power exceeds 3 PWh, 4600 full load hours of operation are reached on average. In case study 2, using the module REMix-PlaSMo, an assessment for Morocco is carried out as to determine limits of volatile power generation in portfolios approaching full supply based on renewable power. The volatile generation technologies are strategically sited at specific locations to take advantage of available resources conditions. It could be shown that the cost optimal share of volatile power generation without considering storage or transmission grid extensions is one third. Moreover, the average power generation cost using a portfolio consisting of PV, CSP, wind and hydro power can be stabilized at about 10 €ct/kWh by the year 2050. In case study 3, using the module REMix-OptiMo, a validation of a TRANS-CSP scenario based upon high shares of renewable power generation is carried out. The optimization is conducted on an hourly basis using a least cost approach, thereby investigating if and how demand is met during each hour of the investigated year. It could be shown, that the assumed load can safely be met in all countries for each hour using the scenario's power plant portfolio. Furthermore, it was proven that dispatchable renewable power generation, in particular CSP imports to Europe, have a system stabilizing effect. Using the suggested concept, the utilization of the transfer capacities between countries would decrease until 2050.

Quantifying the value of CCS for the future electricity system

Abstract: Many studies have quantified the cost of Carbon Capture and Storage (CCS) power plants, but relatively few discuss or appreciate the unique value this technology provides to the electricity system. CCS is routinely identified as a key factor in least-cost transitions to a low-carbon electricity system in 2050, one with significant value by providing dispatchable and low-carbon electricity. This paper investigates production, demand and stability characteristics of the current and future electricity system. We analyse the Carbon Intensity (CI) of electricity systems composed of unabated thermal (coal and gas), abated (CCS), and wind power plants for different levels of wind availability with a view to quantifying the value to the system of different generation mixes. As a thought experiment we consider the supply side of a UK-sized electricity system and compare the effect of combining wind and CCS capacity with unabated thermal power plants. The resulting capacity mix, system cost and CI are used to highlight the importance of differentiating between intermittent and firm low-carbon power generators. We observe that, in the absence of energy storage or demand side management, the deployment of intermittent renewable capacity cannot significantly displace unabated thermal power, and consequently can achieve only moderate reductions in overall CI. A system deploying sufficient wind capacity to meet peak demand can reduce CI from 0.78 tCO2/MWh, a level according to unabated fossil power generation, to 0.38 tCO2/MWh. The deployment of CCS power plants displaces unabated thermal plants, and whilst it is more costly than unabated thermal plus wind, this system can achieve an overall CI of 0.1 tCO2/MWh. The need to evaluate CCS using a systemic perspective in order to appreciate its unique value is a core conclusion of this study.

Assessment viability for hybrid energy system (PV/wind/diesel) with storage in the northernmost city in Africa, Bizerte, Tunisia

Abstract: The absence of clean electricity in Tunisia means a large number of people who are deprived of much needed socioeconomic development. However, wind and solar radiation are two renewable energy resources that are abundantly available in Tunisia. Although, it is not feasible for these two resources separately to meet high electricity demands, hybrid applications can be the best way to get over this weakness. This paper investigated the potential operation of Hybrid Energy System (photovoltaic (PV)/wind turbine/diesel system with batteries storage in the northernmost city in Africa, city of Bizerte in Tunisia. The Hybrid Optimization Model for Electric Renewable simulation software was used to simulate and optimize the technical-economic feasibility of the system. There were several system configurations with and without battery storage elements which will be studied and analyzed. The simulations will be focused on the net present costs, levelized cost of energy, produced excess electricity and the reduction of CO2 emission for the given hybrid configurations. Moreover, the comparison between the economic viability of the stand-alone and the grid-connected HES will be discussed.