Triphenyl phosphate

Abstract: BackgroundOrganophosphate (OP) compounds, such as tris(1,3-dichloro-2-propyl) phosphate (TDCPP) and triphenyl phosphate (TPP), are commonly used as additive flame retardants and plasticizers in a w...

Abstract: Analytical methods were developed for a broad range of organophosphate flame retardants and plasticizers in indoor air. Screening was performed of various indoor environments at 12 locations in and around Zurich, Switzerland. Method recoveries ranged from 62% for triphenyl phosphate to 100% for tris(2-ethylhexyl) phosphate. Tris(2-chloro-isopropyl) phosphate was found in the highest concentration (260 ng/m(3)) mainly in cars and furniture stores. Tris(2-ethylhexyl) phosphate and triphenyl phosphate, both up to 3.4 ng/m(3), were also detected in quantifiable concentrations at several sites. Tris(1,3-dichloroisopropyl) phosphate, tricresyl phosphate and tri(2-butoxyethyl) phosphate were below the limit of quantification in all samples. The results of the risk assessment indicate that the observed concentrations are below the predicted threshold for human health effects.

Abstract: Levels of 12 organophosphate flame retardants (OPs) were measured in particle phase samples collected at five sites in the North American Great Lakes basin from March 2012 to December 2012 (inclusive). The target compounds were three chlorinated OPs [tris(2-chloroethyl) phosphate (TCEP), tris(1-chloro-2-propyl) phosphate (TCPP), and tris(1,3-dichloro-2-propyl) phosphate (TDCPP)], three alkyl phosphates [tri-n-butyl phosphate (TnBP), tris(butoxyethyl) phosphate (TBEP), and tris(2-ethylhexyl) phosphate (TEHP)], and six aryl phosphates [triphenyl phosphate (TPP), tri-o-tolyl phosphate (TOTP), tri-p-tolyl phosphate (TPTP), tris(3,5-dimethylphenyl) phosphate (TDMPP), tris(2-isopropylphenyl) phosphate (TIPPP), and tris(4-butylphenyl) phosphate (TBPP)]. Total OP (ΣOP) atmospheric concentrations ranged from 120 ± 18 to 2100 ± 400 pg/m3 at the five sites, with the higher ΣOP levels detected at Cleveland and Chicago. ΣOP concentrations at these urban sites were dominated by the chlorinated OPs (TCEP, TCPP, and TDCP...

Abstract: The flame retardancy mechanisms of three aryl phosphates, triphenyl phosphate (TPP), resorcinol bis(diphenyl phosphate) (RDP) and bisphenol A bis(diphenyl phosphate) (BDP), in a polycarbonate/acrylonitrile–butadiene–styrene (PC/ABS) blend are investigated and compared. Further, the influence of polytetrafluorethylene (PTFE) on viscosity and thermal decomposition is discussed in the systems PC/ABS and PC/ABS + BDP. Mechanisms are proposed based on the results of various methods. Thermogravimetric analysis, Fourier transform infrared spectroscopy and kinetics are used to study the pyrolysis. The fire behaviour is studied by means of cone calorimeter measurements at different heat fluxes and the flammability is specified by limiting oxygen index (LOI) and UL 94. Rheology measurements are used to illuminate the changed dripping behaviour due to PTFE. TPP shows only a gas phase action. RDP shows mainly a gas phase action and some condensed phase action. BDP shows a crucial condensed phase action in addition to a gas phase action. TPP and RDP are somewhat superior in terms of flammability (LOI), whereas BDP shows superior performance in forced flaming combustion (cone calorimeter). Synergistic effects between PTFE and BDP are found. Copyright © 2007 Society of Chemical Industry

Abstract: New proton-conducting polymer electrolytes based on new porous films of polybenzimidazole doped with phosphoric acid have been obtained. The porous polybenzimidazole films were prepared by leaching out a low-molecular-weight compound using a selective solvent of the porogen from polymer/porogen mixtures. This method allows control over the porosity level up to porosities of 75%. The pore size and morphology strongly depend on the porogen/PBI ratio as observed by SEM. The pore size varies from dimethyl phthalate>diphenyl phthalate>triphenyl phosphate. The acid uptake of the membranes, and therefore the ionic conductivity of the films, increases with the porosity. Ionic conductivity as high as 5 × 10-2 S/cm and mechanically stable membranes are easily obtained by soaking the highly porous films...