Showing papers on "Ultimate tensile strength published in 2011"

Stretching and Breaking of Ultrathin MoS2

Abstract: We report on measurements of the stiffness and breaking strength of monolayer MoS2, a new semiconducting analogue of graphene. Single and bilayer MoS2 is exfoliated from bulk and transferred to a substrate containing an array of microfabricated circular holes. The resulting suspended, free-standing membranes are deformed and eventually broken using an atomic force microscope. We find that the in-plane stiffness of monolayer MoS2 is 180 ± 60 Nm–1, corresponding to an effective Young’s modulus of 270 ± 100 GPa, which is comparable to that of steel. Breaking occurs at an effective strain between 6 and 11% with the average breaking strength of 15 ± 3 Nm–1 (23 GPa). The strength of strongest monolayer membranes is 11% of its Young’s modulus, corresponding to the upper theoretical limit which indicates that the material can be highly crystalline and almost defect-free. Our results show that monolayer MoS2 could be suitable for a variety of applications such as reinforcing elements in composites and for fabricat...

A review on the tensile properties of natural fiber reinforced polymer composites

Abstract: This paper is a review on the tensile properties of natural fiber reinforced polymer composites. Natural fibers have recently become attractive to researchers, engineers and scientists as an alternative reinforcement for fiber reinforced polymer (FRP) composites. Due to their low cost, fairly good mechanical properties, high specific strength, non-abrasive, eco-friendly and bio-degradability characteristics, they are exploited as a replacement for the conventional fiber, such as glass, aramid and carbon. The tensile properties of natural fiber reinforce polymers (both thermoplastics and thermosets) are mainly influenced by the interfacial adhesion between the matrix and the fibers. Several chemical modifications are employed to improve the interfacial matrix–fiber bonding resulting in the enhancement of tensile properties of the composites. In general, the tensile strengths of the natural fiber reinforced polymer composites increase with fiber content, up to a maximum or optimum value, the value will then drop. However, the Young’s modulus of the natural fiber reinforced polymer composites increase with increasing fiber loading. Khoathane et al. [1] found that the tensile strength and Young’s modulus of composites reinforced with bleached hemp fibers increased incredibly with increasing fiber loading. Mathematical modelling was also mentioned. It was discovered that the rule of mixture (ROM) predicted and experimental tensile strength of different natural fibers reinforced HDPE composites were very close to each other. Halpin–Tsai equation was found to be the most effective equation in predicting the Young’s modulus of composites containing different types of natural fibers.

Revealing Extraordinary Intrinsic Tensile Plasticity in Gradient Nano-Grained Copper

Abstract: Nano-grained (NG) metals are believed to be strong but intrinsically brittle: Free-standing NG metals usually exhibit a tensile uniform elongation of a few percent. When a NG copper film is confined by a coarse-grained (CG) copper substrate with a gradient grain-size transition, tensile plasticity can be achieved in the NG film where strain localization is suppressed. The gradient NG film exhibits a 10 times higher yield strength and a tensile plasticity comparable to that of the CG substrate and can sustain a tensile true strain exceeding 100% without cracking. A mechanically driven grain boundary migration process with a substantial concomitant grain growth dominates plastic deformation of the gradient NG structure. The extraordinary intrinsic plasticity of gradient NG structures offers their potential for use as advanced coatings of bulk materials.

As-Fabricated and Heat-Treated Microstructures of the Ti-6Al-4V Alloy Processed by Selective Laser Melting

Abstract: Selective laser melting (SLM) is a rapid manufacturing process that enables the buildup of very complex parts in short delays directly from powder beds. Due to the high laser beam energy during very short interaction times and the high solidification rates of the melting pool, the resulting microstructure is out-of-equilibrium and particularly textured. This type of as-fabricated microstructure may not satisfy the aeronautical criterion and requires post heat treatments. Optimized heat treatments are developed, in one side, to homogenize and form the stable phases α and β while preventing exaggerated grain growth. In the other side, heat treatment is investigated to relieve the thermal stresses appearing during cooling. This study is aimed at presenting the various types of microstructure of the Ti-6Al-4V alloy after postfabrication heat treatments below or above the β transus. Tensile tests are then carried out at room temperature in order to assess the effect of the microstructures on the mechanical properties. The fine as-fabricated microstructure presents high yield and ultimate strengths, whereas the ductility is well below the standard. A strong anisotropy of fracture between the two loading directions is noted, which is attributed to the manufacturing defects. Conventional and optimized heat treatments exhibit high yield and ultimate strengths while the ductility is significantly improved. This is due to a new optimization of the process parameters allowing drastic reduction of the number of defects. These two heat treatments enable now a choice of the morphology of the grains between columnar or equiaxial as a function of the type of loading.

Graphene–aluminum nanocomposites

Abstract: Composites of graphene platelets and powdered aluminum were made using ball milling, hot isostatic pressing and extrusion. The mechanical properties and microstructure were studied using hardness and tensile tests, as well as electron microscopy, X-ray diffraction and differential scanning calorimetry. Compared to the pure aluminum and multi-walled carbon nanotube composites, the graphene–aluminum composite showed decreased strength and hardness. This is explained in the context of enhanced aluminum carbide formation with the graphene filler.

Utilization of silica fume in concrete: Review of hardened properties

Abstract: Several types of industrial byproducts are generated. With increased environmental awareness and its potential hazardous effects, utilization of industrial byproducts has become an attractive alternative to disposal. One such by-product is silica fume (SF), which is a byproduct of the smelting process in the silicon and ferrosilicon industry. Silica fume is very effective in the design and development of high strength high performance concrete. This paper covers the physical, chemical properties of silica fume, and its reaction mechanism. It deals with the effect of silica fume on the workability, porosity, compressive strength, splitting tensile strength, flexural strength, creep and shrinkage of concrete.

Effect of alkali treatment on interfacial and mechanical properties of coir fiber reinforced poly(butylene succinate) biodegradable composites

Abstract: The poly(butylene succinate) (PBS) biodegradable composites reinforced with coir fibers were developed. The effect of alkali treatment on the surface morphology and mechanical properties of coir fibers, interfacial shear strength (IFSS) and mechanical properties of coir fiber/PBS composites was studied. The effect of fiber mass content varying from 10% to 30% on the mechanical properties of coir fiber/PBS composites was also investigated. The coir fibers which are soaked in 5% sodium hydroxide solution at room temperature (RT) for 72 h showed the highest IFSS with 55.6% higher than untreated coir fibers. The mechanical properties of alkali-treated coir fiber/PBS composites are significantly higher than those of untreated fibers. The best mechanical properties of alkali-treated coir fiber/PBS composite were achieved at fiber mass content of 25% in this study, which showed an increase of tensile strength by 54.5%, tensile modulus by 141.9%, flexural strength by 45.7% and flexural modulus by 97.4% compared to those of pure PBS resin. The fiber surface morphologies and fractured surface of the composites exhibited an improvement of interfacial fiber–matrix adhesion in the composites reinforced with alkali-treated coir fibers.

Strong Nanocomposite Reinforcement Effects in Polyurethane Elastomer with Low Volume Fraction of Cellulose Nanocrystals

Abstract: Polyurethane/cellulose nanocrystal nanocomposites with ultrahigh tensile strength and stain-to-failure with strongly improved modulus were prepared by adding cellulose nanocrystals (CNCs) during th ...

Strain-hardening UHP-FRC with low fiber contents

Abstract: This research work focuses on the optimization of strength and ductility of ultra high performance fiber reinforced concretes (UHP-FRC) under direct tensile loading. An ultra high performance concrete (UHPC) with a compressive strength of 200 MPa (29 ksi) providing high bond strength between fiber and matrix was developed. In addition to the high strength smooth steel fibers, currently used for typical UHP-FRC, high strength deformed steel fibers were used in this study to enhance the mechanical bond and ductility. The study first shows that, with appropriate high strength steel fibers, a fiber volume fraction of 1% is sufficient to trigger strain hardening behavior accompanied by multiple cracking, a characteristic essential to achieve high ductility. By improving both the matrix and fiber parameters, an UHP-FRC with only 1.5% deformed steel fibers by volume resulted in an average tensile strength of 13 MPa (1.9 ksi) and a maximum post-cracking strain of 0.6%.

Effect of various chemical treatments on the fibre structure and tensile properties of industrial hemp fibres

Abstract: Industrial hemp fibres were treated with sodium hydroxide, acetic anhydride, maleic anhydride and silane to investigate the influence of treatment on the fibre structure and tensile properties. It was observed that the average tensile strength of sodium hydroxide treated fibres slightly increased compared with that of untreated fibres, which was believed to be as a result of increased cellulose crystallinity. The average tensile strength of acetic anhydride, maleic anhydride, silane and combined sodium hydroxide and silane treated fibres slightly decreased compared with that of untreated fibres, which was believed to be as a result of decreased cellulose crystallinity. However, the average Young’s modulus of all treated fibres increased compared with untreated fibres. This was considered to be as a result of densification of fibre cell walls due to the removal of non-cellulosic components during treatment.